• Transactions of the Korean Society of Automotive Engineers
• /
• v.23 no.6
• /
• pp.601-607
• /
• 2015

The friction material for automobile is manufactured by mixing several composites to stop the running vehicles. Friction characteristics are changed significantly according to the relative amount of the base materials. However, difference of friction coefficient is sometimes measured at the test for the same friction material. Nevertheless, the study for solving these problems is insufficient. In this paper, the friction tests were carried out by changing the external environment and processing condition when the main ingredients are fixed and also evaluated how the friction coefficient changes. The variables are cooling air speed, humidity (Relative humidity and Absolute humidity), scorching time, soaking time and pad area. And it is analytically considered which environmental factor mainly affects the characteristic of friction coefficient variation by experiment. It is expected that the results from this study can be very useful as a database for development of the friction material.

• Journal of the Korean Geotechnical Society
• /
• v.28 no.6
• /
• pp.19-29
• /
• 2012

Pack micropiles were recently developed to improve pile capacity of general micropiles. Pack micropiles were made by warping thread bar or steel pipe of general micropile by geotexlile pack and grouting inside the pack with pressure. According to the pressure, the boring hole could be enlarged. A series of pile uplift tests were performed on three micropiles. Two out of the three piles were the pack micropiles and the other was the general micropile, in which a thread bar was used in the boring hole. According to the pressure applied to the pack micropiles, the diameter of boring hole was enlarged from 152 mm to 220 mm. Unit skin friction mobilized on side surfaces of micropiles increased with displacement of pile head and reached on a constant value, which represents that the relative displacement between piles (or thread bar) and soils was reached on critical state. And the uplift resistance of pack micropile was higher than that of general micropile. Two reasons can be considered: One is that the frictional surface increases due to enlarging diameter of boring holes and the other is that the unit skin friction could increase due to compressing effect of surrounding soils by soil displacement as much as the enlarging volume of boring hole. The compression effect appeared at deeper layer rather than surface layer. The unit skin friction mobilized on micropiles with small diameter was higher than the ones on large bored piles.

• Journal of the Korean Geosynthetics Society
• /
• v.11 no.2
• /
• pp.39-47
• /
• 2012

This paper describes large-scale pullout test results of geosynthetic strip, which can be applied in reinforced earth wall with block-type wall facing. The pullout tests are conducted to evaluate the strain distribution, the induced pullout force and the pullout strength. The maximum pullout force is appeared regardless of reinforcement width and normal stress when end displacement is less than 15 mm. The pullout behavior based on horizontal spacing of reinforcement was similar in relationship between pullout force and end displacement. The strain distribution and pullout force distribution of the geosynthetic strip are concentrated in the front part of reinforcement, and it appeared clearly in higher normal stress condition This means that the pullout behavior of geosynthetic strip is affected by the bond between soil and friction resistance reinforcement according normal stress. Therefore, the pullout resistance design is reasonable when pullout behavior of geosynthetic strip should be evaluated by effective length considering tensile characteristic.

• Korean Journal of Materials Research
• /
• v.5 no.8
• /
• pp.953-959
• /
• 1995

It was investigated that reinforced species, billet condition and extrusion variation in Al 6061 composite material effected on extrusion process of particulate reinforced composite material. The strength of composite material with reinforcement species revealed SiC$\sub$w/> A1$_2$O$\sub$3f/ > A1$_2$O$\sub$3f/ > A1$_2$O$\sub$3f/ orderly. K$\sub$w/ increased as volute fraction increased in all composite material. The composite materials reinforced by A1$_2$ $O_3$required the larger pressure in hot extrusion process than those by SiC$\sub$p/ at all condition. Extrusion process tended to decrease as the semi-angle of extrusion dies increased because larger contact area caused larger shear friction. Extrusion temperature went up about 50$^{\circ}C$ in low elevated deformation temperature. In extrusion temperature above 500$^{\circ}C$, severe tearing occurred on extrusion surface. More reinforcement in volume fraction, more hot tearing.

• Journal of the Korean GEO-environmental Society
• /
• v.17 no.10
• /
• pp.55-62
• /
• 2016

The frequency slope over a year due to climate collapse is connected with huge casualties and property damage, but the situation rarely reduce the damage that gradually increases in size. In order to suppress this, engineers are improved better reinforcement and continued efforts to improve the shear force or withdrawal force. In this study, the GangWhaGu attached to the nail tip that improves the soil nail pullout resistance, and a method to increase the nail integral GangWhaGu maximize the contact area soil - by increasing the friction of the grout seems to increase the effect of slope stability. In order to validate the experiment to determine the effect of reinforcing the soil nail pullout tests of indoor and Behavior GangWhaGu nail and through field tests were conducted and applicability. Experimental results, the case of a pull-out test compared to the GangWhaGu nail through the tensile force of the nail were to increase by approximately 20%.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.13 no.12
• /
• pp.5676-5683
• /
• 2012

In this study, numerical analysis was performed on three shapes of heat transfer plates (chevron, wave and dimple type), which are currently used as fillers of cooling towers. Results show that heat transfer rates per consumed power were larger for enhanced plates as compared with that of plain plate. Highest heat transfer coefficient was obtained for wave shape followed by chevron and dimple shape. For wave shape, cross corrugations induced significant mixing of fluids, which enhanced the heat transfer. Friction factor yielded a similar trend with the heat transfer coefficient. However, heat transfer rate and pressure drop per sheet was the largest for chevron shape, due to the largest heat transfer area per sheet.

• Tribology and Lubricants
• /
• v.30 no.6
• /
• pp.337-342
• /
• 2014

The reduction of drag torque is an important research issue in terms of improving transmission efficiency. Drag torque in a wet clutch occurs because of the viscous drag generated by the transmission fluid in a narrow gap (clearance) between the friction plate and a separate plate. The objective of this paper is to observe the effects of the friction plate area and the clearance on the drag torque using finite element simulation. The two-phase flow of air and oil fluid is considered and modeled for the simulation. The simulation analysis reveals that as the rotational speed increases, the drag torque generally increases to a critical point and then decreases sharply at a high speed regime. The clearance between the two plates plays an important role in controlling drag torque peak. An increase in the clearance causes a decrease in shear stress; thus, the drag torque also decreases according to Newton's law of viscosity. An observation of the effect of the area of contact between transmission fluid and friction plate shows that the drag torque increases with the contact area. The flow vectors inside the flow channel present clear evidence that the velocity of the fluid flows is faster with a larger friction plate, that is, in the case of a larger contact area. Therefore, the optimum size of the friction plate should be determined carefully, considering both the clutch performance and drag reduction. It is expected that the results from this study can be very useful as a database for clutch design and to predict the drag torque for the initial design with respect to various clutch parameters.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.18 no.1
• /
• pp.302-309
• /
• 2017

The influence of the pile diameter, center to center pile spacing, internal friction angle of embankment soil, and height of embankment on the arching efficacy of the embankment pile was investigated. The arching efficacy, which was derived by the arch model developed in the embankment soil was calculated using two methods, one that considers crown failure of the arch and the other that considers load on the pile cap and critical relative spacing ratio for which the arching efficacy calculated by the two methods are the same. According to the computed results in this study, the arching efficacy calculated from a consideration of the load on pile cap governs when the relative spacing ratio becomes smaller and that calculated from the theory of crown failure governs when the relative spacing ratio becomes larger. The critical relative spacing ratio below which the arching efficacy calculated from a consideration of the load on pile cap governs the design decreases with increasing value, which is defined by the ratio of the pile diameter to the pile center to center spacing. Critical relative spacing ratios, which correspond to the values of 0.5 and 0.2 were 0.35 and 0.85, respectively. Considering the computed results, the critical relative spacing ratio decreases with increasing Rankine passive earth pressure coefficient and critical relative spacing ratios, which correspond to values of 5 and 2, were 0.23 and 0.85, respectively. The arching efficacy, which corresponds to the area ratio of 9%, was 54% and the one that corresponds to the value of 3 was 61%; the critical relative spacing ratios, which correspond to those arching efficacies, were greater than 0.5.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.27 no.6
• /
• pp.79-85
• /
• 2023

Skid resistance pavement is an accessory to the road and is a facility for the safe driving of cars by increasing the skid resistance of road pavement. In particular, in bad weather conditions such as snow, rain, and black ice, the skid resistance performance of skid resistance pavement greatly affects the safety of road traffic and drivers. However, BPT(British Pendulum Tester) has a test area of only 0.009 m², making it difficult to represent the overall packaging surface. A reliable method of evaluating slip resistance performance is needed for maintaining non-slip packaging. In this study, the conventional BPT test and the skid resistance performance evaluation method of the PFT(Pavement Friction Tester) and µGT(Micro Grip Tester) tests were compared through guidelines and standard investigations and applied to the field skid resistance performance evaluation. In addition, skid resistance pavement with different skid resistance performance was installed at the test-bed and actual road demonstration sites to compare BPN(British Pendulum Number), SN(Skid Number), GN(Grip Number), and to derive correlations for each performance evaluation method. As a result of the experiment, SN and GN showed similar skid resistance performance, and the GN value was derived similar to BPN × 0.01.

• Proceedings of the Korea Technical Association of the Pulp and Paper Industry Conference
• /
• 2000.04a
• /
• pp.148-149
• /
• 2000

황금배는 1967년에 신고에 이십세기를 교배하여 1977년 1차선발과 1982년 2차선발을 거 쳐 1984년 최종선발, 명명한 품종으로, 당도가 높고 육질이 부드러워서 최근 몇년 사이에 캐 나다, 미국, 호주, 그리고 유럽 지역에서의 수요가 급증하고 있는 수출전망이 매우 밝은 품 종 중의 하나이다(92년 재배면적 lOha 수출량 5. 8M/T, 95년 재배면적 150ha 수출량 2 200.6M/T), 황금배는 비교적 대과이고 과형은 원형에 가까운 편원형으로서 사과 골든처럼 과피가 황금색이고 과육은 연황백색으로 투명하며 보기에 극히 미려한 특징이 있다. 아울러 육질이 유연치밀하고 과즙이 극히 많으며 당도가 높아 13$^{\circ}$ Bx이상, 15도 Bx까지 측정되는 둥 감산이 적화되어 맛이 극히 우수하다. 그러나 이러한 황금배는 동녹, 흑반병 등 병충해로 인한 상품가치의 하락으로 현재 수요를 충족시키지 못하고 있는 실정이다. 1 16세기부터 씌워진 과실봉지는 초기 병해충을 방지할 목적만으로 사용되어 왔지만, 현 재는 방균과 방충의 효과와 함께 자연현상의 최적화를 위한 차광성, 발수성, 투기성을 조절 하며 과실의 외관까지 영향을 미치는 바, 과실봉지의 기능성 부여를 위해서는 고도의 기술 력이 요구되고 있다 하겠다. 상기한 배에 방균방충처리된 과설봉지를 씌워서 재배하면 농 약 살포횟수를 줄이고 배에 농약이 직접 묻지 않아 배의 농약오염을 예방할 수 있으며, 봉 지 안으로의 해충이나 균의 침투를 원천적으로 봉쇄할 수 있다. 그러나 기존의 황금배용 봉 지는 비록 기타 병충해 피해를 방지하는 효과는 있었으나, 동녹을 억제하는 효력이 다소 미 흡하였다. 과피의 비정상적인 코르크화로 인해 발생하는 동녹은 과피의 물리적 할렬과 생리적 장 해에 의해 발생하는 것으로 알려져 있다(永澤 1940). 과실이 비대해짐에 따라 과피의 기공 (과점)이 할렬하면서 코르크화가 진행되는데 그 발생정도나 시기는 배의 품종에 따라 다르 나 일반적으로 코르크화는 기상조건, 특히 습도와 밀접한 관련이 있다고 알려져 있다 황금 배의 재배에 봉지를 적용하면 일반적으로 과피의 코르크화가 억제되는데 그러한 이유는 다 음과 같이 설명할 수 있다. 과실은 하루를 주기로 하여 수축과 팽창을 반복하면서 비대화하 는데 이러한 현상은 과실 내의 수분 조건에 따르는 것으로, 봉지재배의 경우 무대재배보다 단기간에 변화되는 습도의 범위가 좁아 급변을 방지하기에 과점의 할렬이 완화될 수 있다. 즉, 봉지를 씌웅으로서 봉지 내의 대기 환경이 외기보다 안정적으로 유지되고 직사광선이나 농약 및 마찰로부터 과실을 보호해 주기에 동녹이 어느 정도 방지될 수 있는 것이다. 그러나 기존의 황금배봉지는 동녹의 정도를 완화시킬 뿐 완전히 방지할 수 없었으며, 봉지를 적 용한 재배조건에서의 동녹발생 기구를 정확히 이해하지 못했었기에 효과적으로 봉지의 기능 을 개선하는 것이 불가능하였다. 과설의 미려도는 과실의 맛과 함께 그 가치를 결정짓는 중요한 물성으로서 우리나라 황 금배 재배환경과 특성에 알맞은 배봉지의 제작이 선결될 때, 배 품질의 향상, 안정된 공급이 가능하게 될 것이며 아울러 농가의 수업증대와 수출 경쟁력 강화가 이루어질 수 있을 것으로 판단된다. 이러한 측면에서 황금배 재배농가가 당면한 동녹발생의 문제점을 신속한 해결 을 위한 새로운 기능성 국산 황금배 봉지의 개발이 절실히 요구되고 있다. 위와 같은 문제를 해결하기 위하여 본 연구에서는 과실봉지의 종류간에 동녹발생 정도 가 상이한 점에 예의 주시하여 다양한 봉지의 적용실험을 통해 다음과 같은 결과를 얻었다. 황금배의 동녹 발생 정도는 배봉지의 발수성과 투기 및 투습도에 의해 크게 영향받는다. 상기한 바와 같이 과점의 코르크화로 인해 동녹이 발생된다고 할 때, 봉지 내의 습기 및 웅결수의 양은 황금배의 동녹에 중대한 영향을 미친다. 태양광이 내려찍는 낮 시간동안 황 금배는 증산작용을 하며 습기를 배출하는데 봉지 내의 온도가 높은 낮 시간 동안 수분이 습기로 존재하지만 기온이 급격히 떨어지는 일몰 이후에는 상대습도가 높아짐에 따라 결로 현상으로 인해 응결수가 된다. 이때 응결수와 접촉한 과피는 건조한 상태보다 세균의 침입 이 용이할 뿐만 아니라 기공(과점)의 호홉에 지장이 초래됨에 따라 과점의 할렬이 더욱 조 장되어 코르크화를 유발하고 결과적으로 동녹이 발생한다고 판단된다. 따라서 만일에 봉지 의 투기, 투습도가 양호하여 봉지 내의 과다한 수분이 충분히 배출될 수 있었다면, 수분의 응결을 피하고 동녹을 완화시킬 수 있을 것이라 판단되었다.