• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.49 no.4
• /
• pp.47-52
• /
• 2012

We have designed the waveguide to microstrip transition using a probe structure for the center frequency of 200 GHz transceiver. The waveguide to microstrip transition is composed of probe, taper and microstrip transmission line. For design of the transition, we simulated the lengths and width of the probe and the taper to optimize the center frequency and the bandwidth using HFSS simulation tool from Ansoft. The transition is designed back-to-back structure. From the simulation results, the transition exhibits that insertion loss is below - 0.81 dB and the return loss less than -10 dB in range of 186 ~ 210 GHz.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.15 no.9
• /
• pp.722-728
• /
• 1990

A comppact waveguide to microstrip transition to be used for measurements of the performances of the U-band MMIC power amplifier is designed and fabricated. A Tchebyscheff ${\lambda}$/4 impedence transformer is adopted as an impedence converter of the transition. The designed transition is optimized to get Su less then -28dB over the 40-to-48GHZ band using Supper Compact program. The measured results shows that insertion loss and return loss are typically 0.3 and 25dB respectively over 40-to-47GHz.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.19 no.12
• /
• pp.1435-1444
• /
• 2008

In this paper, we designed a reduced height waveguide(WG) to microstrip mode converter with a short transition length. The mode converter is composed of a mode converter using E-plane probe and a modified impedance transformer. The mode converter was designed using a probe shorted to top of a 50 ohm ridge WG. The modified impedance transformer was designed to connect the mode converter to the reduced height WG. For wide bandwidth operation, the coupling of the two parts was tuned. The structure of the mode converter was optimized for low loss and wide bandwidth, and the optimized mode converter was fabricated. The performance of the mode converter was extracted using the thru and line S-parameters for back-to-back connections, and the connector loss was calibrated. The mode converter has a right angle structure and short transition length, 7.2 mm. The mode converter shows excellent performances; the insertion loss of 0.12 dB at 15 GHz, and the return loss above 10 dB for the full Ku-band.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.9 no.4
• /
• pp.473-482
• /
• 1998

In this paper, characteristics of the wide band microstrip antennas with parasistic element are analyzed by the Finite Difference Time Domain(FDTD) method, and antenna parameters are optimized to get maximum bandwidth, retern loss, input impedance, and radiation pattern are calculated by Founier transforming the time domain results. The characteristics of the antenna are varied and the bandwidth of the antenna is broaded as a length and a width of the driven element, a gap of the driven element and the parasitic element, a width and a length of parasitic element. So the different patchs are resonating at different frequencies and this multipule resonance increase the bandwidth. The Results of the calculation and measurement, the size of the antenna with parasitic element is about a twice larger than a microstrip antenna, but bandwidth is four times better than a microstrip antenna. And these results were in relatively good accordance with the measured values.

• Journal of Advanced Marine Engineering and Technology
• /
• v.36 no.1
• /
• pp.149-156
• /
• 2012

In this study, we propose a novel transmission line employing inverted PACD (Periodically Arrayed Capacitive Devices) for application to a development of miniaturized passive components on MMIC. The novel microstrip line employing Inverted PACD structure showed a loss much lower than conventional microstrip line. Using the inverted PACD structure, we fabricated a miniaturized impedance transformer on MMIC. the size of the impedance transformer was 0.012 $mm^2$, which is only 1.7% of conventional one. The impedance transformer showed good RF performances in a frequency range of 2.25~6.5 GHz.

• Proceedings of the KAIS Fall Conference
• /
• 2006.05a
• /
• pp.381-383
• /
• 2006

본 논문에서는 5.8Ghz ISM대역 평행 결합선로 대역통과 여파기를 설계 제작하였다. 긴본적인 설계는 저역통과 여파기에서 대역통과 여파기로 변환한 후, 직 병렬 공진기를 이용한 설계와 J-인버터를 이용해 평행 결합선로 대역통과 여파기를 구현하였다. 2개의 공진 주파수를 실제로 구현하기 어렵기 때문에 하나의 공진기만을 사용하기 위해 인버터를 사용하였다. 또한 실제적인 마이크로스트립 라인의 layout크기를 결정하기 위해 우수 기수 모드 임피던스를 해석하고 근사식을 통해 스트립라인의 치수를 결정하였다. 이런 과정을 토대로 5.8GHz ISM밴드용 평행 결합선로 대역통과 여파기를 설계, 제작하였다.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.28 no.4
• /
• pp.286-297
• /
• 2017

This paper is a study of 6~18 GHz wideband high power amplifier which is composed of 10 single amplifier and coaxial type spatial power combiner. The property of this spatial power combiner is on a similar principle to antipodal antenna radiation mechanism. Therefore, the key structure of proposed spatial power combiner is the antipodal finline PCB board and the finline curve shape is numerically synthesized by using Klopfensein's optimum impedance taper. The measured CW output power of spatial combined high power amplifier is nearly 50 W. In conclusion we prove the good combining performance between the spatial power combiner and 10 single amplifier over 6~18 GHz frequency ranges. Also, we developed the key component PA and MFC MMIC which controls the phase and gain of the each amplifier, The main characteristic of MFC MMIC is to maximize combining efficiency of power amplifier.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.41 no.12
• /
• pp.93-102
• /
• 2004

This paper presents a general theory for the analysis of an aperture-coupled cavity-fed microstrip patch antenna to develop a simple but accurate equivalent circuit model. The developed equivalent circuit consists of ideal transformers, admittance elements, and transmission lines. These circuit element values are computed by applying the complex power concept, the Fourier transform and series representation, and the spectral-domain immittance approach. The input impedance of the antenna is calculated and compared with the published data. Good agreements validate the simplicity and accuracy of the developed equivalent circuit model.

• Journal of the Korean Institute of Telematics and Electronics
• /
• v.18 no.6
• /
• pp.23-29
• /
• 1981

By using a slot-line in combination with microstrip lines, a coplanar wide-band balun is designed and fabricated. The slot-line of balun junction is compensated to be operated in C-band(4~8GHz), and therefore the results are agreement with theoritical prediction. Experimental data are given for a 3-section Chebyshev transformer-matched balun with a balanced-to-unbalanced line impedance ratio of 2 : 1. A bandwidth from 3.5GHz to 7.0GHz is obtained with V.S.W.R. of below 1.2 : 1. Maximum insertion loss is measured as 0.9dB, and the phase difference varies linearlly within 180$^{\circ}$$\pm$5$^{\circ}$.

• Journal of Advanced Navigation Technology
• /
• v.15 no.4
• /
• pp.578-584
• /
• 2011

This paper presents the design and measured performances of an unequal dual-band power divider using lumped elements. After the divider is designed using the conventional single band Wilkinson topology with lumped elements, we obtained the dual band characteristics with filter conversion method. This design method has the features of compact size and easy fabrication, because the high impedance transmission line realizes the lumped elements of equivalent circuit. As an example, an 2:1 divider has been designed and measured at 880 MHz and 1650 MHz in order to show the validity of the proposed unequal divider. The measured performances of the unequal power divider agree with the simulation results.