• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.37 no.12
• /
• pp.1159-1165
• /
• 2013

Powder blasting, which is an efficient micromachining method for glass, silicon, and ceramics, has a critical disadvantage in that the surface finish is poor owing to the brittle fracture of materials. Low-pressure waterjet machining can be applied to smoothen the rough surface inside the blasted structure. In this study, the surface roughness and sectional dimension of micro-channels are observed during the repetitive application of a waterjet to blasted micro-channels. The asperities and subsurface cracks created by blasting are removed by waterjet machining. Along with the surface roughness, it is found that the sectional dimension increases and the edges of the finished micro-channel become slightly round. Finally, a microfluidic chip is machined by the blasting-waterjet process and a transparent microfluidic channel is obtained efficiently.

• Journal of Advanced Navigation Technology
• /
• v.4 no.1
• /
• pp.23-35
• /
• 2000

In this paper, the design for a PCS base station antenna which is using broadband method by a stacked structure has been studied. The sensitive parameters, such as the parasitic elements, the height of air layer between the upper and lower patch, and the variation of feed point, of the microstrip antenna that has stacked structure in a characteristics variation situation are classified and the characteristics has been investigated through the simulations. A designed antenna has following characters. Impedance bandwidth is Z57.5MHz(VSWR${\leq}$2), horizontal beamwidth is $64.1^{\circ}$, and gain is 14.7dBi. Therefore, it is confirmed the characteristics is good. In this paper, through the designing of a stacked microstrip antenna, we has investigated the availability for Korea PCS base station antenna.

• Journal of the Korean Vacuum Society
• /
• v.20 no.4
• /
• pp.294-299
• /
• 2011

In this study, single-walled carbon nanotubes (SWCNTs) were synthesized on a Fe/$Al_2O_3$/Si layer by thermal chemical vapor deposition. Metallic SWCNTs were selectively removed by microwave irradiation. Electrical and structural characterizations of the SWCNTs clearly revealed that the metallic SWCNTs were almost removed by microwave irradiation for 120 sec. The remained semiconducting SWCNTs with a high crystalline structure were obtained over 95%. This method would provide useful information for applications to SWCNTs-based field effect transistors and multifaceted nanoelectronics.

• The Journal of The Korea Institute of Intelligent Transport Systems
• /
• v.17 no.5
• /
• pp.128-134
• /
• 2018

In this paper, two ports feeding a microstrip patch antenna using a quadrature hybrid circuit was proposed to enhance the bandwidth for the global positioning system(GPS). The square patch was designed, and the probe feeding was applied. The quadrature hybrid chip circuit for two-port feeding was designed, and output ports that have a 90-degree phase difference feed to the patch antenna. The designed patch and quadrature hybrid circuit were implemented on an FR4 board, and were combined. The measurement of the bandwidth within a voltage standing wave ratio(VSWR) of 2:1 and axial ratio(AR) in 3dB were wide band as 29% BW (1,230~1,700 MHz) and 15.87% BW (1,400~1,650 MHz), respectively. Antenna gain were measured 2.75dBi at the center frequency.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.34 no.7
• /
• pp.671-677
• /
• 2010

In the present study, we designed a microfluidic platform for generating monodisperse droplets with diameters ranging from hundreds of nanometers to several micrometers. To generate fine droplets, T-junction and flow-focusing geometry are integrated into the microfluidic channel. Relatively large aqueous droplets are generated at the upstream T-junction and transported to the flow-focusing geometry, where each droplet is broken into smaller droplets of the desired size by the action of pressure and viscous stress. In this configuration, the flow rate of the inner fluid can be made very low, and the ratio of the inner- and outer-fluid flow rates in the flow-focusing region can be made very high. It has been shown that the present microfluidic device can generate droplets with diameters of approximately $1\;{\mu}m$ (standard deviation: <3%).

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.38 no.5
• /
• pp.567-573
• /
• 2014

Since the development of microelectromechanical systems (MEMS) technology for the medical field, various micro-fluid transfer systems have been studied. This paper proposes a micro-piezoelectric pump that imitates a stomach's peristalsis by using two separate piezoelectric elements, in contrast to existing micro-pumps. This piezoelectric pump is operated by using the valve-less traveling wave of peristalsis movement. If the piezoelectric plates at the two separated plates are actuated at the input voltage, a traveling wave occurs between the two plates. Then, the fluid migrates by the pressure difference generated by the traveling wave. Finite element analysis was performed to understand the mechanics of the combined system with piezoelectric elements, elastic structures, and fluids. The effects of design variables such as the chamber height and number of ceramics on the flow rate of the fluid were examined.

• Korean Journal of Food Science and Technology
• /
• v.20 no.3
• /
• pp.326-330
• /
• 1988

For the automation of Koji incubation process, microcomputer based Koji incubation system was built and applied to acquisition of the process variables, and to control of the Koji incubation process. The incubation variables included the relative humidity and Koji weight. And data measured were sent to the microcomputer by the interface device built with MC 6821 PIA. Incubation environment conditions -temperature and humidity- were controlled by the actuation of heater and mist sprayer with on/off signal generated by ASIC program. Aspergillus oryzae as a starter of the Koji and steamed barley as media were used and Koji was successfully manufactured both at $25^{\circ}C,\;70%$ RH and at $27^{\circ}C,\;80%$ RH. During the Koji preperation, the temperature was linearly increased and substrate was consumed stepwise showing 3 steps in the weight loss curve.

• Journal of the Korean Institute of Telematics and Electronics D
• /
• v.36D no.8
• /
• pp.54-61
• /
• 1999

This paper proposes a new optic link structure applicable to broad-band wireless access microcellularsystem servicing in the millimeter wave frequency band. The proposed structure utilizes photonic mixing by exploiting the nonlinear property of EOMs, which leads to the frequency up-conversion at the CS and thus, electrical mixing at a BS is not required. Moreover, via transmitting an additional optical millimeter wave carrier into the Bs, the dispenses with an active optic source, which miniaturizes the BS. We analyze CNR, IM3/C in the downlink and SFDR in the uplink. Through simulation using the typical parameter values we also show the feasibility of the proposed system based on the requirements in the current microcellular system.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.11 no.1
• /
• pp.26-36
• /
• 2000

A circularly polarized $12\times12$ array with application in the satellite communications is designed at 10 GHz. The radiator is an aperture-coupled ring patch, which is suitable of large arrays. The element spacing of the array is chosen to be $0.7\lambda_0$to maintain the main beam in the broadside direction. The array is a sequential array constructed on a series-parallel feed network to obtain high gain and low axial ratio. Measurement results for the array, acquired by experiments in the compact range of POSTECH, showed a directivity of 27.88 dB, a high gain of 25.55 dB, an efficiency of 60%, an axial ratio of 1.74 dB, and a side-lobe level of -13 dB. The bandwidth of the array was 43% when the VSWR was 2, and the bandwidth of the axial ratio was 16%.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.41 no.8
• /
• pp.37-44
• /
• 2004

This paper describes a new GaAs-based surface-micromachined microstrip line supported by dielectric post and air-gapped signal line with ground metal. This new type of dielectric-supported air-gapped microstripline(DAML) structure is developed using surface micromachining techniques to provide easy means of airbridge connection between the signal lines and to archive low losses at millimeter-wave frequency band with wide impedance range. Each DAMLs with the length of 5 mm are fabricated and the measured characteristics are compared with those of the conventional microstrip transmission line. These transmission lines are composed of 10 ${\mu}{\textrm}{m}$ height of signal line, post size of 10 ${\mu}{\textrm}{m}$ ${\times}$ 10 ${\mu}{\textrm}{m}$ and post height of 9 ${\mu}{\textrm}{m}$. By elevating the signal lines from the substrate using the micromachining technology, the substrate dielectric loss can be reduced Compared with of the conventional microstrip transmission line showing 7.5 dB/cm loss at 50 GHz, the loss can be reduced to 1.1 dB/cm loss at 50 GHz.