• The Journal of the Korea institute of electronic communication sciences
• /
• v.6 no.6
• /
• pp.865-871
• /
• 2011

DC-DC converter commonly used in photovoltaic systems or fuel cell systems is a boost converter. Among several types of boost converter, the interleaved boost converter with small input and output current ripples is widely used in recent years. Because of small input and output current ripples, the circuit can reduce the size of the input and output capacitors. Thus, instead of conventional electrolytic capacitor, the film capacitor with high reliability can be used and this is the life and reliability of the entire system can be improved. In this paper, the input/output current ripple formulas of the multi-stage interleaved boost converter are derived, and the characteristics in accordance with duty are found out. In order to verify the above mentioned contents, the derived results will make a comparison with the calculated values by using PSIM tool.

• The Journal of the Korea institute of electronic communication sciences
• /
• v.7 no.6
• /
• pp.1429-1435
• /
• 2012

DC-DC converter commonly used in photovoltaic systems, fuel cell systems and electric vehicles is a boost converter. The interleaved boost converter, connected in parallel by several boost converters and operated by the phase difference to reduce the input and output current ripple, has been widely used in recent years. Because of small input and output current ripples, the circuit can reduce the size of the input and output capacitors. Thus, instead of conventional electrolytic capacitor, the film capacitor with high reliability can be used and this is the life and reliability of the entire system can be improved. In this paper, the output current ripple formulas of the multi-stage interleaved boost converter are derived, and the characteristics in accordance with duty are found out. In order to verify the abovementioned contents, the derived results will make a comparison with the calculated values by using PSIM tool.

• Proceedings of the KIPE Conference
• /
• 2020.08a
• /
• pp.441-442
• /
• 2020

본 논문에서는 2상 하이브리드 스테핑 모터의 디텐트 토크 보상 기법을 제안하였다. 2상 하이브리드 스테핑 모터의 회전자 좌표계 d,q축 전압 방정식 및 토크 식으로부터 지령 토크 발생을 위해 필요한 d,q축 전류를 지령으로 사용하며, 디텐트 토크로 인해 발생하는 속도 리플을 제거하기 위해 리플 크기를 추출하여 전류지령에 보상하였다. Matlab/Simulink를 이용한 2상 하이브리드 스테핑 모터 구동 시뮬레이션을 통해 제안된 기법의 유효성을 확인하였다.

• Proceedings of the KIPE Conference
• /
• 2013.11a
• /
• pp.44-45
• /
• 2013

본 논문은 3상 PMSM 동작 중 한 개의 상이 고장이 났을 경우, 2상을 통하여 고장허용 동작을 하는데 있어서 발생하는 토크 리플 저감 방법에 대하여 연구를 하였다. 기존의 방법들이 기본파 주파수로 회전하는 동기좌표계상에서 전향 보상 방식으로 교류 성분의 전류를 제어함으로써 토크 리플을 보상하는 데에 반해 제안한 방법은 기본파 주파수의 2배수로 회전하는 동기좌표계상에서 직류 성분의 전류로 토크 리플을 보상하기 때문에, 저속 운전뿐만 아니라 고속 운전시에도 그 보상 특성이 매우 우수하다. 제안한 방법은 자동차용 전동식 조향 시스템에 적용하여 그 유효성을 실험적으로 검증하였다.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.15 no.3
• /
• pp.235-243
• /
• 2010

This paper describes a design method of LCL filter for grid-connected three-phase PWM inverter. First, by analyzing the ripple component of phase voltages and currents according to the PWM pattern of grid-connected three-phase inverter, the RMS value of the current ripple can be calculated. Then based on the analysis, the current THD in the inverter-side can be defined. After that by analyzing the dependency between the current THD of the system and the current ripple attenuation, the parameter of LCL filter can be designed. Finally, the described LCL filter design method is verified by showing a good agreement between the target current $THD_g$ and the actual one through the simulation and experiment.

• Journal of the Institute of Electronics Engineers of Korea TE
• /
• v.42 no.2
• /
• pp.7-14
• /
• 2005

This paper presents a method to reduce torque ripple of brushless DC motor by compensating phase delay due to winding inductance. For considering torque ripple comes from the phase winding inductance, torque equation of one phase is derived as Fourier series that is function of the delay. From the equation, also the resultant equation that the current delay is compensated is derived. It is validated that the compensated torque has a form of Fourier series for rectangular wave that is ideal torque, and torque ripple is reduced, consequently. Experimental method for the compensation is realized by replacing switching pattern of inverter by pattern of compensated rotor position. The effectiveness of the proposed method to reduce torque ripple has been demonstrated by the simulation and experimental results using 3 phase 4 pole brushless DC moor.

• 한국신재생에너지학회:학술대회논문집
• /
• 2010.11a
• /
• pp.73.2-73.2
• /
• 2010

휴대용 전자기기들의 소비전력 증가에 따라 2차전지에 비해 에너지 밀도가 높은 연료전지를 이용한 충전기의 필요성이 부각되고 있다. 대다수의 충전기는 On-Grid 방식으로 벅타입 컨버터를 이용한 감압 방식이었으나, 연료전지를 이용할 경우 승압식 컨버터를 통한 배터리의 충전이 요구된다. 또한 배터리는 일반 저항부하와 달리 큰 커패시턴스 성분을 가지고 있기 때문에 컨버터의 출력단에 인덕터가 없는 경우 큰 출력 리플전류를 유도하게 되어 시스템의 효율과 배터리의 수명에 좋지 않은 영향을 끼치게 된다. 또한 이를 해결하기 위해 절연형 감압 컨버터를 사용하는 경우 변압기 사용에 의한 부피 증가와 부가 소자의 사용에 따른 가격 상승을 피하기 어렵다. Cuk 컨버터는 주스위치의 ON/OFF 동작에 관계없이 출력으로 에너지가 항상 전달되며, 이상적으로 리플이 거의 존재하지 않아 충전용으로 적합하다. 또한, 승압 및 감압이 자유롭기 때문에 배터리의 정격전압에 상관없는 범용 충전기의 설계도 가능하다. 따라서 본 논문에서는 Cuk 컨버터를 이용하여 배터리 충전기를 설계하고, 그의 상태공간 모델링, 주파수 특성 해석 및 제어기 설계에 대해 기술한다. 제안된 제어 방식은 소형 연료전지 스택을 이용하여 실제 배터리를 대상으로 한 정전류 및 정전압 제어를 실행하여 그 성능 및 안정성을 검증한다.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.11 no.4
• /
• pp.328-339
• /
• 2006

In this paper the characteristic analysis of a single-phase switched reluctance motor (SRM) drive system with power factor correction (PFC) circuit is presented. The SRM is a low cost, simple and has a good high speed performance. The SRM drive with diode rectifier and filter capacitor has a low power factor because of short switch on time of capacitor. A novel switching topologic is presented to improve power factor and reduce torque ripple based on analysis of PFC circuit. Accordingly the SRM drive system with PFC circuit is also presented. Through the numerical analysis of the system, the toque ripple, power factor and efficiency with the change of rotary speed, load torque and capacity of the capacitor are achieved and compared with actual measured value.

• Journal of the Korean Society of Marine Environment & Safety
• /
• v.25 no.6
• /
• pp.802-808
• /
• 2019

DC motors are used extensively on shipboard, including as the ship's winch operating motor, owing to their simple speed control and excellent output torque characteristics. Moreover, they were used as propulsion motors in the early days of electric propulsion ships. However, mechanical rectifiers, such as brushes, used in DC motors have certain disadvantages. Hence, brushless DC (BLDC) motors are increasingly being used instead. While the electrical characteristics of both types of motors are similar, BLDC motors employ electronic rectifying devices, which use semiconductor elements, instead of mechanical rectifying devices. The inverter system for driving conventional BLDC motors uses a two-phase excitation method so that the waveform of the back electromotive force becomes trapezoidal. This causes harmonics and torque ripple in the phase current switching period in which the winding wire through which the current flows is changed. Researchers have studied and presented various methods to reduce the harmonics and torque ripple. This study applies a cascaded H-bridge multilevel inverter, which implements a proportional-integral speed current controller algorithm in the driving circuit of the BLDC motor for electric propulsion ships using a power analysis program. The simulation results of the modeled BLDC motor show that the driving method of the proposed BLDC motor improves the voltage waveform of the input side of the motor and remarkably reduces the harmonics and torque ripple compared with the conventional driving method.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.9 no.5
• /
• pp.457-466
• /
• 2004

In this paper, a modified converter is presented and analyzed to use as a photovoltaic converter. And also a new parallel driving scheme is proposed to increase output power and to reduce the output voltage ripple. The ratio of the output to the input voltage of the modified converter is equal to that of the boost converter. The difference between both converters is the composition of output terminal. Owing to the discrepancy, a working voltage of the output capacitor of the modified converter becomes lower, thus the capacitance value of the capacitor can be smaller than that of the boost converter. The proposed parallel driving is based on the modified converter and a current-mode-control method. It gives a good solution for alleviating the current sharing unbalance problem of conventional parallel operations. It reduces the output voltage ripple by means of increasing the equivalent switching frequency without additional switching losses. The validity of the proposed parallel driving strategy is verified through computer-aided simulations and experimental results.