• Applied Chemistry for Engineering
• /
• v.9 no.5
• /
• pp.786-790
• /
• 1998

K-GIC of the new carbon electrode to improve performance of carbon negative electrode in lithium ion secondary battery was prepated and its electrical characteristics were studied. Form this study, intercalated K quantity was increased in order of $2>3>1mole/{\ell}$ of KCl solution. And, for KCl solution of 1mole, the mole ratio of carbon and potassium was 156~388 carbon/potassium. The proper condition of K-GIC preparation was KCl solution of $1mole/{\ell}$, reaction temperature of $700^{\circ}C$, reaction time of 1 hour. From this condition, the intercalation and deintercalation behavior of lithium was very excellent. Also the reversibility was excellent.

• Polymer(Korea)
• /
• v.34 no.5
• /
• pp.430-433
• /
• 2010

The gasket materials of for the lithium ion battery requires chemical resistance to electrolyte, electrical insulating, compression set, anti-contamination and low temperature property. To check the special characteristics of fillers which are applied to rubber for gasket, compound of EPDM, NBR and FKM (fluoro elastomer) were made by adjusting weights of carbon black and silica additive. Using these compounds, we had done tests of long-term stability against electrolyte, compression set and low-temperature property with considering operating condition of the lithium ion battery. From this test, we investigated the physical and chemical characteristics of rubber with using of carbon black and silica additive in each.

• Resources Recycling
• /
• v.10 no.6
• /
• pp.9-14
• /
• 2001

A sulfuric acid leaching of $LiCoO_2$as cathodic active materials of lithium ion secondary batteries was investigated in terms of reaction variables. In the absence of a reducing agent, the extraction of cobalt was less than 40% in 2 M sulfuric acid at $75^{\circ}C$ instead of that of lithium could be almost 100% in the same conditions. To improve the Co extraction, hydrogen peroxide was used as a reducing agent in the range 2~20 vol%. When over 10vo1% hydrogen peroxide was added, the extractions of both metals were improved to about 95%. It seems to be due to the reduction of Co(III) to Co(II) that can be readily dissolved. The extractions of Co and Li were increased with increasing $H_2$$SO_4$concentration and temperature, and amount of hydrogen peroxide and with decreasing of pulp density. The optimum leaching conditions were determined at $2 M H_2$$SO_4$concentration, $75^{\circ}C$ operating temperature, 100 g/L. initial pulp density, 20 vol% $H_2$$O_2$addition and 30 min.

• Polymer(Korea)
• /
• v.26 no.1
• /
• pp.45-52
• /
• 2002

The separator made from the blends of high density polyethylene (HDPE) and ultrahigh molecular weight polyethylene (UHMWPE) was prepared by wet processing to use as Li-ion secondary battery. We investigated effects of the blending of the polymers and the film extension on the mechanical properties of the separator. The mechanical strength of separator increased with increasing molecular weights and contents of UHMWPE, for instance about $1000 kg/\textrm{cm}^2$ with the five times extended film of 6 wt% UHMWPE. The pores of the separator were very uniform with the size of 0.1~$0.12\mu\textrm{m}$. The shut-down characteristic quickly increased at around $130^{\circ}C$ and the fusion temperature was $160^{\circ}C$, so it could be applied to the lithium ion secondary battery.

• Elastomers and Composites
• /
• v.45 no.3
• /
• pp.212-216
• /
• 2010

The materials of the lithium ion battery gasket require chemical resistance to the electrolyte, electrical insulating, compression set, anti-contamination and heat resistance. To estimate suitability for rubber which has better performance to compression set than PFA, each compound were made with various rubbers, such as EPDM, NBR, FKM, FVMQ, VMQ and we checked the characteristics of each compound. Samples from each compound was deposited in Propylene Carbonate and tested for changing of Hardness and Volume during 1,000 hr with $80^{\circ}C$. EPDM and VMQ showed good performance to chemical resistance to the electrolyte, and also we could get the values over $10^{10}{\Omega}cm$ on volume resistance basis in electrical insulating. EPDM and VMQ were judged as the most suitable material.

• Korean Chemical Engineering Research
• /
• v.56 no.1
• /
• pp.42-48
• /
• 2018

Silicon has attracted extensive attention due to its high theoretical capacity, low discharge potential and non-toxicity as anode material for lithium ion batteries. In this study, Si-CNT-C composites were fabricated for use as a high-efficiency anode material in a lithium ion battery. Aerosol self-assembly and post-heat treatment processes were employed to fabricate the composites. The morphology of the Si-CNT-C composites was spherical and an average particle size was $2.72{\mu}m$. The size of the composite increased as concentration of Si and CNT increased in the precursor solution. In the Si-CNT-C composites, CNT and C carbonized from glucose were attached to the surface of Si particles. Electrochemical measurement showed that the cycle performance of Si-CNT-C composites was better than that of silicon particles.

• Applied Chemistry for Engineering
• /
• v.33 no.4
• /
• pp.343-351
• /
• 2022

Lithium-ion batteries (LIBs) are considered promising energy storage devices with good performance such as high energy density, slow self-discharge rate, high rate charge capacity, and long battery life. However, the application of these LIBs in the high-energy density electric vehicle and large device industries poses a major safety problem. In order to solve this problem, developing a material having high thermal stability and intrinsic safety is the ultimate solution for improving the stability and electrochemical performance of LIBs. This review introduced a surface modification technology of a separator to overcome the stability problem of a commercial separator, and summarized and summarized the research trends using the modified separator for a lithium-ion battery. Based on this, the future prospects for the separator development by surface modification were discussed.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.39 no.6
• /
• pp.639-644
• /
• 2015

A cylindrical secondary Li-ion cell is a device in which stored chemical energy is converted to electrical energy via an electrochemical reaction. These cells are widely used for applications that require high capacity and rate power, such as notebooks, power tools, and electric vehicles. The role of a center pin is to retain the channel for gas release, preventing blockage of the hollow of the jelly roll during a charge-discharge cycle, and to prevent an internal short circuit for tearing of separator under mechanical free fall. In this paper, two experiments are conducted with and without the center pin to experimentally verify the importance of the role of the center pin. The first experiment is a 50-cycle charge-discharge cycle test, and the second is a free fall test conducted according to the Underwriters Laboratories (UL) standards. Based on these experiments, we demonstrate that the center pin in a cylindrical cell is a very important component in terms of safety.

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2018.06a
• /
• pp.138-138
• /
• 2018

선박을 통한 해상수송은 세계 무역의 80% 이상을 차지하고 있으며, 대부분의 선박은 저질중유의 연소로부터 추진력을 발생시키는 디젤 엔진을 원동력으로 사용하고 있다. 이러한 디젤 엔진은 연소의 부산물로 매년 백만 톤 이상의 오염물질을 방출하는데, 그 주성분은 탄소로 이루어져 있고 고온 열분해 또는 압축 점화 엔진의 작동 부산물들이 소량 포함되어 있다. 이에 본 연구에서는 선박으로부터 배출된 폐 수트를 리튬이온전지용 도전재로 활용하기 위한 독특한 방법이 제안되었다. 실험에 사용된 폐 수트는 운항중인 컨테이너선으로부터 수집되었으며, 수집된 폐 수트는 탄소 성분 이외의 불순물을 제거하고 흑연화 정도를 개선시키기 위해 $2,000^{\circ}C$로 열처리되었다. 열처리된 폐 수트의 모폴로지를 확인하기 위해 투과전자현미경을 이용하여 그 형상을 관찰하였으며, 이를 통해 폐 수트의 일차 입자는 지름이 약 70-100 nm 정도인 양파껍질 모양의 탄소(carbon nano-onion)로 형성된다는 것이 확인되었다. 또한, XRD, RAMAN 분광법 및 BET 분석 결과를 통해, 열처리된 폐 수트가 결정성이 있는 흑연으로 재형성되었으며 비표면적은 일반적으로 사용되는 활물질에 비해 약간 더 높다는 것을 확인할 수 있었다. 한편, 이러한 특성은 리튬이온전지용 도전재로 활용될 수 있는 가능성을 보여주었고, 이는 전기화학적 정전류 충전 및 방전 테스트를 통해 그 성능이 확인되었다. 일반적으로 사용되는 도전재의 테스트 결과와 폐 수트를 도전재로 사용한 테스트 결과를 Fig. 1에 나타내었다. 이상의 실험 결과들을 미루어 볼 때, 선박으로부터 배출된 폐 수트가 리튬전지용 음극 활물질 및 도전재로 재활용될 수 있을 것으로 사료된다.

• Proceedings of the KIPE Conference
• /
• 2016.07a
• /
• pp.411-412
• /
• 2016

최근 퍼스널 모빌리티에 대한 관심과 수요가 증대됨에 따라 전기에너지를 구동원으로 하는 소형 이동형 제품을 생활속에서 쉽게 접할 수 있게 되었다. 이러한 퍼스널 모빌리티 제품은 자이로센서 기술이 접복된 바퀴가 하나인 외발 전동휠과 세그웨이류의 제품, 전동퀵보드, 전동스쿠터 등 다양한 제품이 출시되고 있다. 또한 이들 제품의 구동전원은 대부분 리튬이차전지가 사용되고 있다. 본 논문에서는 충전과 방전을 반복하는 다셀이 직렬로 구성된 리튬 이차전지 배터리팩에서 발생되는 셀간 편차와 이로 인해 배터리팩의 전체적인 효율성이 저하되는 것을 방지하는 셀 밸런싱에 관한 기술로 과거 완속형의 표준충전에 적합한 1단 밸런싱의 문제점을 보완하기 위해 표준충전과 급속충전을 임의로 선택하여 사용하는 경우에도 정상적인 셀 밸런싱 수행은 물론 빠른 셀 밸런싱을 수행하기 위한 기법에 대해 살펴보았다.