• The Journal of the Korea institute of electronic communication sciences
• /
• v.19 no.1
• /
• pp.85-92
• /
• 2024

In this paper, we developed an intuitive teaching and control system that directly teaches a task by holding the tip of a robotic arm and moving it to a desired position. The developed system consists of a 6-axis force sensor that measures position and attitude forces at the tip of the robot arm, an algorithm for generating robot arm joint speed control commands based on the measured forces at the tip, and a self-made 6-axis robot arm and control system. The six-dimensional force/torque of the position posture of the robot arm operator steering the handler is detected by the force sensor attached to the handler at the leading edge and converted into velocity commands at the leading edge to control the 7-axis robot arm. The verification of the research method was carried out with a self-made 7-axis robot, and it was confirmed that the proposed force sensor-based robot end-of-arm control method operates successfully through experiments by teaching the operator to adjust the handler.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.14 no.5
• /
• pp.1112-1118
• /
• 1990

The end tip position control of a flexible robot arm has been presented by utilizing the feedback signal from the rate-gyro mounted at the end tip. Kalmann filter and the state feedback gains were determined by optimal sense based upon the parameter from the geometrical and electrical data of the flexible arm system. The simulation and experiment were performed and it has been proved that implementation of the rate-gyro drastically improves the performance.

• The Journal of the Korea institute of electronic communication sciences
• /
• v.17 no.5
• /
• pp.933-940
• /
• 2022

In this paper, the algorithm was developed to recognize hand 3D position through 2D image sensor and implemented a system to remotely control the 6 d.o.f. robot arm by using it. The system consists of a camera that acquires hand position in 2D, a computer that controls robot arm that performs movement by hand position recognition. The image sensor recognizes the specific color of the glove putting on operator's hand and outputs the recognized range and position by including the color area of the glove as a shape of rectangle. We recognize the velocity vector of end effector and control the robot arm by the output data of the position and size of the detected rectangle. Through the several experiments using developed 6 axis robot, it was confirmed that the 6 d.o.f. robot arm remote control was successfully performed.

• Journal of the Institute of Convergence Signal Processing
• /
• v.3 no.2
• /
• pp.76-82
• /
• 2002

The objective of this paper is to design a robust controller for a flexible robot arm manipulator using LMI(Linear Matrix Inequality) theory, and confirm its effectiveness through experimentation. We first describe a modeling Process of the flexible arm in order to get a mathematical model, and then discuss how to approximately obtain the uncertainty of the model for robust control. As to the control system design, we adopt the LMI-based H$_{\infty}$ synthesis algorithm which has the merits of eliminating the regularity restrictions attached to the Riccati-based methods. As a result of this, we can cope with the parameter variation (that is, modeling uncertainty) due to the tip-load variation. Finally we confirm the effectiveness of the controller through experiment and simulation.

• Journal of the Korean Society for Precision Engineering
• /
• v.15 no.1
• /
• pp.26-34
• /
• 1998

In this paper, a force control algorithm for edge following task is suggested. Through the contact state modeling between rigid part and end-effector of robot, contact force and contact angle that are essencial parameters to build the control strategies for following movement of end-effector are derived. From these two parameters, we discriminate the every contact state into 8 cases and calculate the new moving position and direction simply. For the experiment. RX90 robot from Staubli with robot language V$^{+}$ is applied and F/T sensor is attached to the wrist of robot with RCC. Finally, 3 edge following experiments including the following of corner point are executed with successful results.s.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.33 no.2
• /
• pp.631-642
• /
• 2013

The standard CPT(Cone Penetration Test), which can be easily performed to investigate in-situ soil engineering properties, has been widely used. CPT are also widely being utilized in centrifuge model tests. In this study, a miniature cone with 10mm diameter was developed and its applicability in the centrifuge was evaluated. The developed miniature cone was equipped with a four degree-of-freedom in-flight robot. A series of cone penetration tests was performed under four centrifuge acceleration levels. As results, the cone resistances measured at the same confining stress within shallow penetration depth were affected by the centrifugal accelerations. The critical depth was proportional to the cone diameter and relative density. Cone resistances results below the critical depth and soil parameters obtained from the laboratory tests were compared with those by previously proposed empirical relations.

• 제어로봇시스템학회:학술대회논문집
• /
• 1997.10a
• /
• pp.1493-1495
• /
• 1997

Cropping of head and tail ends of rod in wire Rolling Process is required to aviod roll damage, and prevent cobbles. In order to reduce the crop loss, the new crop control system for rotary shear of Wire rolling Process has been developed. Performance shows the developed system cut precisely within setting length. As a result, it is expected to increase the yield ratio of products about 0.2 percent and stabilize the operantional condition.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2022.10a
• /
• pp.566-569
• /
• 2022

In this paper, the algorithm was developed to recognize hand golve gesture and implemented a system to remotely control the robot. The system consists of a camera and a controller that controls robot motion by hand position gesture. The camera recognizes the specific color of the glove and outputs the recognized range and position by including the color area of the glove. We recognize the velocity vector of robot motion and control the robot by the output data of the position and the detected rectangle. Through the several experiments, it was confirmed that the robot motion control was successfully performed.

• 제어로봇시스템학회:학술대회논문집
• /
• 1993.10a
• /
• pp.1036-1041
• /
• 1993

The tip of the flexible robot arm has to be controlled by the active control reducing vibration because it has residual vibration after getting to desired position. This paper presents an end-point position control of a 1-link flexible robot arm having tip mass by the PID control algorithm. The system is composed of a flexible arm with tip mass, dc servomotor and ballscrew mechanism under translational motion. The feedback signal composed of the tip displacement measured by laser sensor, estimated velocity and acceleration is used to control the base motion. Theoretical results are obtained by applying the Laplace transform and the numerical inversion method to the governing equations. After the flexible robot arm reaches to. the desired position, the residual vibration is controlled by the PID algorithm. This paper gives the simulation and experimental results of end-point responses according to changing tip-mass and arm length. And this algorithm shows good effects of reducing the residual vibration. Approximately, theoretical response is in good agreement with experimental one.

• Journal of Institute of Control, Robotics and Systems
• /
• v.4 no.6
• /
• pp.738-746
• /
• 1998

This paper presents a neural network-based adaptive controller for a single flexible-link. The control for feedback-error loaming of neural network is designed by using the re-definition approach. The neural network controllers are implemented on an single flexible-link experimental test-bed. The tip response is significantly improved and the vibrations of the flexible modes are damped very fast. Experimental and simulation results are presented of the proposed tip position tracking controllers over the conventional PD-type, passive controllers.