• Restorative Dentistry and Endodontics
• /
• v.33 no.6
• /
• pp.553-559
• /
• 2008

The purpose of this research was to compare the microtensile bond strength of resin coated surface and resin inlay according temporary filling materials prior to applying self-adhesive resin cement. Caviton(GC, Japan), Provifil(Promedica, Neumunster, Germany), Provifil(Promedica, Neumunster, Germany) & petrolatum, and Eugenol-based cement, Tembond(Kerr, Orange CA, USA) were used as temporary filling materials. After fabrication of Tescera(Bisco, Schamburg IL, USA), it was bonded with a self-adhesive resin cement, Rely X unicem(3M, St. Paul. Minn, USA). After this procedure, the microtensile bond strength was measured and it was analyzed through one-way ANOVA and Duncan test(p<0.05). Caviton(GC, Tokyo, Japan) showed statistical difference except for the control(group I) and the saliva(group II)(p<0.05). Provifil(group IV), Provifil & petroneum(group V), Tembond(group VI) had lower microtensile bond strength.

• Journal of Dental Rehabilitation and Applied Science
• /
• v.18 no.3
• /
• pp.157-170
• /
• 2002

The purpose of this study is to analyze the shear bond strength according to kinds of surface treatment agents and resin cements after acid etching of IPS Empress 2. For this purpose, test groups were classified into silane-treated bonding groups, silica-coated group and Targis link applied group. Then, nine bonding groups in total, each three groups per kind, were prepared by using three kinds of resin cements-Panavia F, Variolink II and Rely-X ARC, and thirty test specimens per group were prepared. To examine any changes in the oral environment, the shear bond strength of each test specimen was measured after dipping test for 24 hours and for five weeks, respectively, in distilled water at $37^{\circ}C$ and performing heat cycle 10,000 times in total, each 2,000 times per week, during a five weeks of dipping, under the condition similar to the oral environment. The bond failure modes were also observed by means of a scanning electron microscope. The results are summarized as follows 1. Statically significant differences between the surface conditioning materials were observed. The shear strength of the silane treatment was the highest of all three types of surface treatments(p<0.001). 2. Shear strengths varied significantly for different types of resin luting agents. But bond strength of Targis link surface treatments were not significantly different(p<0.05). 3. No significant difference of bonding strengths was found between storage time conditions(24 hours and 5 weeks). Only group II, IV, VII, IX were significantly different(p<0.05). 4. After thermocycling, the shear bond strengths of all groups were significantly decreased (p<0.05). Group III, V, VI were no significantly different. 5. On the SEM observation of fractured surfaces, all groups were shown complex failure.

• Polymer(Korea)
• /
• v.31 no.6
• /
• pp.526-531
• /
• 2007

This paper reports the first results of a series of planarization film study for the stainless steel (SS) substrates for flexible displays. Diglycidyl ether of bisphenol A (DGEBA) and octa(dimethylsiloxypropylglycidylether) silsesquioxane (OG) were chosen for the organic and the hybrid epoxies respectively and diaminodiphenylmethane (DDM) was used as a curing agent at 1:2 stoichiometric ratio. These materials were spin-coated on SS substrates and thermal-cured. TGA study indicated that both the pristine and the cured OG were more thermally stable than DGEBA. AFM study showed that the smooth surfaces of $1{\sim}2\;nm$ roughness can be prepared for both DGEBA and OG when the films were thick ($>\;1\;{\mu}$). The electrical properties such as dielectric constant, capacitance and the leakage current with respect to the applied voltage were all stable even after the stress of $100\;V/100^{\circ}C$ was applied for $0{\sim}10000$ seconds indicating that the insulating properties of DGEBA and OG films were very reliable.