• Proceedings of the KSME Conference
• /
• 2004.04a
• /
• pp.1120-1125
• /
• 2004

Welding characteristics of STS304 stainless steel and Inconel 600 using a continuous wave Nd:YAG laser are experimentally investigated. Alloy 600 being used in steam generator tubing of pressurized water reactor(PWR) exposed to some corrosion environment, stress corrosion cracking can occur on this material. Presented here are the results from a series of experiments in which dissimilar metal welds were made using the gas tungsten arc welding process with pure argon shielding gas. But It is well known that solidification cracking susceptibility of austenitic alloys depends on the solidification temperature range and amount/distribution of solute rich liquid that exists at the terminal stages of solidification. An experimental study was conducted to determine effects of welding parameters and to optimize those parameters that have the most influence on eliminating or reducing the extent welding zone formation at dissimilar metal welds.

• Journal of the Korea Institute of Military Science and Technology
• /
• v.10 no.3
• /
• pp.109-113
• /
• 2007

Laser welding process for wing of a guided weapon is studied. Nd;YAG pulse laser beam is used to weld the skin(STS304, thickness: 1mm) to frame(AMS 5398) of wing. Optimal laser welding condition is obtained from the mechanical testing and observation of the welded joint.

• Journal of the Korean Society for Precision Engineering
• /
• v.30 no.1
• /
• pp.67-76
• /
• 2013

We present an innovative real-time laser welding monitoring technique employing the correlation analysis of the plasma plume optical emission generated during the process. The plasma optical radiation emitted during Nd:YAG laser welding of S45C steel samples has detected with a Photodiode and analyzed under different process conditions. The discrete DC voltage difference, filter methods and wavelet transform has been used to decompose the optical signal into various discrete series of sequences over different frequency bands. Considering that wavelet analysis can decompose the optical signals, extract the characteristic information of the signals and define the defects location accurately, it can be used to implement process-control of laser welding.

• Transactions of Materials Processing
• /
• v.7 no.6
• /
• pp.519-529
• /
• 1998

In automotive industries the stamping of laser-welded blank gives many merits which bring about dimensional accuracy, strong body assembly and high productivity. However the welding of blanks with different thickness or/and different strength materials introduces many challenging formability problems for process development and tool design. in this paper the deformation characteristics for deep drawing process of laser-welded blank with different thickness sheets are investigated by experiment as well as by FEM simulation. The blank holding force ratio to avoid the movement of weld line was suggested and compared with the experimental result for cylindrical and rectangular cup drawing process. The optimal location of weld line in laser-welded blank with different thickness sheets is calculated to compensate for the movement of weld line on deep drawing process. In addition the effect of location of weld line on formability is clarified using FEM simulation.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2021.11a
• /
• pp.4-5
• /
• 2021

In irregular curtain walls, the nominal stress required for each member varies greatly depending on the shape, so it is inefficient to design members based on the maximum required stress. Then, built-up members are absolutely necessary, but built-up members manufactured by Manpower-welding cannot be constructed in an irregular curtain wall building because it' not precise. In order to address the problems, this paper presents why Robotic-laser-welding should be used in irregular curtain walls using Gwanggyo Galleria Department Store involving 3D printing as an example. Results verify the performance of Robot-Laser-Welding as an efficient solution for precise steel curtain wall members.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.19 no.6
• /
• pp.96-101
• /
• 2020

In this paper, we present the results of our research to perform 3D laser scanning functions by adding a focusing lens to a conventional 2D laser scanner. For the optical design, the ray-tracing technique was used along with a total of four lenses as the variable incident focusing lens, the collimating lens, and the F-Theta lens. As design variables, the curvature of the incident focusing lens (Lens #1) was assumed to be us, l mm and sumed mm, and the incident angles were set at 0cidenus, l. In addition, the distance between the focusing lens and the collimating lens was set to vary from 5 mm to 15 mm. When the incident focal length was varied from 5 mm to 15 mm, the exit focal length was calculated to vary from 67.5 mm to 56.8 mm for the lens with R = 100 mm and from 108.5 mm to 99.0 mm for the lens with R = 150 mm. When the incident angle was 0°, the focal aberration was only slightly observable at 10㎛ in both the x- and y-direction. At 7.5° was the focal aberration of approximately 20~50㎛ was measured at 20㎛. To investigate the chromatic aberration of the designed optical device, the distortion of the focus was observed when the 550 nm beam was simulated on lens designed for a 980 nm wavelength.

• Laser Solutions
• /
• v.8 no.3
• /
• pp.11-19
• /
• 2005

In automotive industry, light weight vehicle is one of issues because of the air pollution and the protection of environment. Therefore, automotive manufacturers have tried to adopt light materials such as aluminum alloy to production line. Aluminum welding using laser has some advantages high energy density and high productivity. It is very important to understand weld characteristic according to welding condition in order to determine the possibility of application to car body. In this study, Nd:YAG laser welding of 5182 aluminum alloy with filler wire AA5356 was carried out through experimental design according to wire feed rate, laser power and welding speed. Weld bead shape in terms of cross section photo, bead with, height of reinforcement and penetration depth and mechanical property in terms of tensile strength and formability was investigated. Analysis of variation (ANOVA) was performed to know the effect of weld parameter for weldability, laser power was statistically most significance factor of three variables.

• Proceedings of the Korea Committee for Ocean Resources and Engineering Conference
• /
• 2001.10a
• /
• pp.292-300
• /
• 2001

The paper describes spectroscopic characteristics of plasma induces in the pulsed YAG laser welding of alloys containing a large amount of volatile elements. The authors have conducted the spectroscopic analyses of laser induced Al-Mg alloys plasma in the air and argon atmosphere. In the air environment, the identified spectra were atomic lines of Al, Mg, Cr, Mn, Cu, Fe and Zn, and singly ionized Mg lines, as well as the intense molecular spectra of A10 and Mg0 formed by chemical reactions of evaporated Al and Mg atoms from the pool surface with oxygen in the air. In argon atmosphere, Mg0 and AI0 spectra vanished, but AIH spectrum was detected. The hydrogen source was presumably hydrogen dissolved in the base metals, water absorbed on the surface oxide layer, or $H_2$ and $H_2O$ in the shielding gas. The resonant 1ines of Al and Mg were strongly self-absorbed, in particular, self-absorption of the Mg 1ine was predominant. These results show that the laser induced plasma was made of metal1ic vapor with relatively low temperature and high density.

• Laser Solutions
• /
• v.13 no.3
• /
• pp.1-6
• /
• 2010

The in-process monitoring of $CO_2$ welding of Zn-coated steel plates has been studied and compared with that of conventional thin plates. Relationships between weld defects and plasma emission signals were evaluated in laser lap joint of thick Zn-coated steel. According to the study, weld defects were found to increase with Zn content. As a result, measured plasma emission signals also decreased. In case of plate with $15{\mu}m$-thick Zn-coated layer, defects caused by evaporation of Zn could, therfore, controled by gap of 0.1mm, resulting in a stable emission signals. However, the amplitude of signals fluctuated very widely. Variation of amplitude sould be limited in 3-8V by FFT smoothing.

• Journal of the Korean Society for Precision Engineering
• /
• v.20 no.7
• /
• pp.44-55
• /
• 2003

The Nd:YAG laser process is known to have high speed and deep penetration capability to become one of the most advanced welding technologies. This paper describes the machining characteristics of SM45C carbon steel welding by use of an Nd:YAG laser. In spite of its good mechanical characteristics, SM45C carbon steel has a high carbon contents and suffers a limitation in the industrial application due to the poor welding properties. The major process parameters studied in the present laser welding experiment were position of focus, travel speed and laser power. Optical microscope and SEM were used to investigate the microstructures of the welded zone. The experimental results showed that penetration depth of the welding process increases with laser power. Both the microstructural investigation and the theoretical calculations indicated that materials undergoes a very high heating and cooling cycle during welding process. It was also found that the austenite nucleation takes place at the initial stage and the completion temperature of austenite transformation is much higher than in the case of the arc welding.