Laser-induced incandescence (LII) 측정법은 조사된 레이저에 의하여 입자가 가열됨에 따라서, 그 온도에 상응하는 흑체복사의 시간적 감소추이가 입자의 크기에 따라서 달리 나타나는 것을 이용하여 입자의 크기를 측정하는 방법이다. LII 감쇄법은 레이저에 의하여 가열된 입자의 에너지 균형 상관식에서 입자의 크기가 클수록 신호의 감쇄속도가 느리고, LII 신호의 감쇄비가 실험적으로 입자의 크기에 비례한다는 사실을 이용하여 연소진단에 응용되어 왔다. (중략)
잔류응력은 공학적 구조물에 결함을 야기하는 유해한 응력이므로 산업현장에서는 이를 측정하기 위한 많은 관심을 가지고 있다. 현재 잔류응력 측정은 일반적인 방법을 사용하고 있지만 이러한 방법들은 어느정도 문제점을 내포하고 있다. 그러므로 레이저 스페클 간섭법에 유한요소법과 점 가열법을 혼합하여 산업 현장에 유해한 잔류응력을 측정할 수 있는 새로운 기법을 개발하였다. 이 기법에서 사용된 레이저 스페클 간섭계는 측정 시편의 응력이 풀릴 때의 면내 변형을 측정하기 위해서 사용되어 졌으며, 유한요소법은 응력 풀림을 위한 가열부의 온도와 그 밖의 변수들을 결정하기 위해서 사용되어 졌다. 잔류응력은 측정하고자 하는 부위의 가열 냉각에 의한 변형률에 의해 결정되어지며, 이에 대한 간단한 모델링을 제시하였다. 또한 본 실험은 변형의 3차원 정량화를 수행하기 위해서 레이저 스페클 간섭계의 전자 광학적 기법 중의 하나인 위상이동법을 이용하여 수행되어졌다.
Laser induced incandescence, LII, recently developed technique for measuring soot concentration in flames, can overcome most of limitations of conventional laser extinction measurement. In this study, experiments were performed to investigate the effect of laser intensity, detection wavelength, and also laser beam quality on both LII signal at a particular position and peak-to-centerline LII signal ratio. The results of LII signal with increasing laser intensity shows its near-independence of laser intensity once threshold level of laser intensity has been reached. However, this near-independence depends on laser beam quality and the incident optical setup. The peak-to-centerline LII signal ratio slowly but continuously increases with laser power. This fact is due to the dependence of LII signal on particle mean diameter. LII signal is attenuated during it passes through the flame containing soot particles. The attenuation rate is inversely proportional to detection wavelength. In this study, LII signal at 680 nm band is 10% greater than the signal at 400 nm band.
광자기 메모리용 재료인 비정질 TbFe 박막을 대상으로 열자기 기록시 박막에 분포하는 온도와 이때 만들어지는 bit의 크기간에 상호관련성을 조사하였다. 레이저 조사에 의해 가열된 박막의 온도분포는 유한요소법을 이용한 열전달 해석에 의해 계산하였다. 레이저 가열종료 직전 박막 면에 분포하는 온도 contour로 부터 bit 크기를 예측하였다. 여기서 bit 크기는 온도 상승에 따라 보자력이 약화되어 외부자계와 박막반자장의 합력이 역자구를 만들어 준다고 가정하여 이 경계가 되는 온도(Tcrit)로 이루어지는 등온선의 크기로부터 정하였다. 열자기 기록 실험으로부터 기록 bit의 크기(Dmeas.)을 측정하여 레이저조사조건별로 예측한 bit크기(Dpred.)와 비교하였다. 특히, 레이저 pulse시간 변화에 따른 여러온도의 등온선 contour 직경변화를 조사하여 실측한 bit크기와 비교 검토함으로써 bit형성에 미치는 온도분포의 영향을 조사하였다. 이 결과 레이저 pulse시간이 길어지거나 레이저 power가 상대적으로 작을때 실측한 bit크기가 예측된 bit크기보다 커지는 것으로 나타났으며 이는 Tcrit 온도구배가 완만해질수록 bit경계가 되는 온도가 낮아지는 것으로 해석된다.
An experimental study on LII signal images from soot particles in a flame has been carried out in order to investigate the effect of the incident laser characteristics. By changing the wavelength of the incident laser beam, the LII signal was saturated at smaller laser power with 532 nm than 1,064 nm. This implies that the larger absorption coefficient of soot particles at 532 nm would influence the LII signal characteristic. Using the deconvolution technique, the projected LII line images were coverted to reconstruct the local LII signals inside the beam. The results show that the LII images at ICCD camera result from the integration of LII signal across the laser beam.
Residual stress is one of the causes which make defects in engineering components and materials. Many methods have been developing to measure the residual stress. Though these methods provide the information of the residual stress, they also have disadvantage like a little damage, time consumption, etc. In this paper, we devised a new experimental technique to measure residual stress in materials with a combination of laser speckle pattern interferometry and spot heating. The speckle pattern interferometer measures in-plane deformation during the heat provides for much localized stress relief. 3-D shape is used for determining heat temperature and other parameters. The residual stresses are determined by the amount of strain that is measured subsequent to the heat and cool-down of the region being interrogated. A simple model is presented to provide a description of the method. In this paper, we could experimentally confirm that residual stress can be measured by using laser interferometry and spot heating method.
CIGS박막을 동시 증발법(co-evaporation)으로 몰리브덴이 증착된 소다라임 유리 위에 성장시켰다. CdS 박막은 화학적 용액 성장법 (chemical bath deposition: CBD)을 이용하여 약 60 nm를 증착하였다. 열처리는 가열판 (hot-plate)을 사용하여 공기중에서 하였다. 열처리 온도는 0~350$^{\circ}C$까지 변화하였으며, 열처리 시간은 각각 5분이었다. 시료의 표면 및 계면의 변화를 SEM측정을 통하여 관측하였다. CdS/CIGS 박막의 열처리 온도 변화에 따른 photoluminescence 특성을 조사하였다. 여기 레이저는 488 nm ($Ar^+$ laser)와 632.8 nm (He-Ne laser)를 사용하여 결함의 근원을 조사하였다. 온도 의존성 실험을 통하여 CIGS 박막의 띠 간격 에너지를 확인할 수 있었으며, 결함 준위의 활성화 에너지 및 특성을 알 수 있었다. $Ar^+$ laser에서만 관측되는 신호의 근원은 CdS에 기인한 것이었다.
To quantify the LII signals from soot particle of flames in diesel engine cylinder, a new method has been proposed for correcting LII signal attenuated by soot particles between the measuring point and the detector. It has been verified by an experiment on a laminar jet ethylene-air diffusion flame. Being proportional to the attenuation, the ratio of LII signal at two different detection wavelengths can be used to correct the measured LIIsignal and obtain the unattenuated LII signal, from which the soot volume fraction in the flame can be estimated. Both the 1064-nm and frequency-doubled 532-nm beams from the Nd : YAG laser are used. Single-shot, one-dimensional(1-D) line images are recorded on the intensified CCD camera, with the rectangular-profile laser beam using 1-mm-diameter pinhole. Two broadband optical interference filters having the center wavelengths of 647 nm and 400 nm respectively and a bandwidth of 10 nm are used. This two-wavelength correction has been applied to the ethylene-air coannular laminar diffusion flame, previously studied on soot formation by the laser extinction method in this laboratory. The results by the LII measurement technique and the conventional laser extinction method at the height of 40 nm above the jet exit agreed well with each other except around outside of the peaks of soot concentration, where the soot concentration was relatively high and resulting attenuation of the LII signal was large. The radial profile shape of soot concentration was not changed a lot, but the absolute value of the soot volume fraction around outside edge changed from 4ppm to 6.5 ppm at r=2.8mm after correction. This means that the attenuation of LII signal was approximately 40% at this point, which is higher than the average attenuation rate of this flame, 10~15%.
When thermal diffusivity is measured by laser flash method, the thermal diffusivity call be calculated front the assumption of the uniformly heated whole surface of the specimen. It has been known that the approximate 5% error is made by the non-uniform energy distribution on the specimen surface of laser pulse heat source. In this study, to obtain the highly-uniformed laser beam, which has both the low non-uniform heating error from non-uniform laser beam and the energy loss, research was carried out on no transmitting loss by optical fiber and high repetitions. In addition, heating error and thermal diffusivity were measured as the measuring positions were varied and compared with the results using the uniform and the non-uniform laser beams. In addition, dole to using the uniformalized laser beam, the whole surface of the specimen was heated uniformly and as a result, it was the thought that this was very effective to reduce the variations of the errors of the thermal diffusivity as the measuring positions were varied. It can be obtained that when the thermal diffusivity of POCO-AXM-5Q1 of SRM in NBS was measured with both the uniform and the non-uniform laser beams, the dispersion error of the former was from 2 to 2.5%, which was more improved than that of the latter.
현재까지 알려진 마이크로 레이저 호스트용 물질 중에서 가장 우수한 물리적 특성을 갖고 잇는 LaSc3(BO3)4를 융액 인상법 조건하에서 단결정으로 육성시킬 수 있는 최적 성장조건을 규명하고자 하였다. 우선 LaSc3(B(3)4의 융융특성을 규명하기 위해 DTA에 의해 La(BO3)-Sc(BO3)계의 상평형도를 작성한 결과, 이 2성분계에서 LaSc3(BO3)4는 유일한 중간상(Intermediate phase)이었으며, 용융 전에 1495 ±2℃에서 Sc(BO3)와 융액으로 분리되는 비조화 분해반응(peritectic reaction)을 나타내었다 : LaSc3(BO3)4=Sc(BO3)+melt 히타 및 도가니의 상호관계와 단열 혹은 보온상태를 적절히 조절함으로써, 성장로의 열구조를 단결정 성장에 적합하게 하기 위해 열전대를 애프터히타 최상부로부터 융체 내부까지 상승 또는 하강시키면서 4개의 열 구조에 대해 온도분포와 온도구배를 측정 및 산출하였으며, 장단점을 비교하여 최적 성장조건을 확립하였다. LaSc3(BO3)4는 부조화 용융특성이 있으므로 화학양론적 조성에 La(BO3)를 다소 추가하여 특성 성분의 융액을 만들고, 인상속도를 0.7mm/hr이하, 회전속도는 7-10rpm의 환원조건 하에서 단결정을 성장시킬 수 있었다. 또한 결정성장때, Ir 및 백금 도가니를 사용할 수 있으나, 도가니의 수명은 가열/용융/냉각 주기가 최대 8-10회이다. 실험 결과 배플판 직경 등의 애프터 히타의 구조를 변화시킴으로써, 도가니 상부의 온도를 50-100℃ 증가시키는 것이 가능하였으며, 수직 및 수평적 온도구배는 배플판의 직경에 정비례하여 증감하였고, 특히 수평적 온도구배는 열구조에 의한 의존성이 크다는 것이 확인되었다.
본 웹사이트에 게시된 이메일 주소가 전자우편 수집 프로그램이나
그 밖의 기술적 장치를 이용하여 무단으로 수집되는 것을 거부하며,
이를 위반시 정보통신망법에 의해 형사 처벌됨을 유념하시기 바랍니다.
[게시일 2004년 10월 1일]
이용약관
제 1 장 총칙
제 1 조 (목적)
이 이용약관은 KoreaScience 홈페이지(이하 “당 사이트”)에서 제공하는 인터넷 서비스(이하 '서비스')의 가입조건 및 이용에 관한 제반 사항과 기타 필요한 사항을 구체적으로 규정함을 목적으로 합니다.
제 2 조 (용어의 정의)
① "이용자"라 함은 당 사이트에 접속하여 이 약관에 따라 당 사이트가 제공하는 서비스를 받는 회원 및 비회원을
말합니다.
② "회원"이라 함은 서비스를 이용하기 위하여 당 사이트에 개인정보를 제공하여 아이디(ID)와 비밀번호를 부여
받은 자를 말합니다.
③ "회원 아이디(ID)"라 함은 회원의 식별 및 서비스 이용을 위하여 자신이 선정한 문자 및 숫자의 조합을
말합니다.
④ "비밀번호(패스워드)"라 함은 회원이 자신의 비밀보호를 위하여 선정한 문자 및 숫자의 조합을 말합니다.
제 3 조 (이용약관의 효력 및 변경)
① 이 약관은 당 사이트에 게시하거나 기타의 방법으로 회원에게 공지함으로써 효력이 발생합니다.
② 당 사이트는 이 약관을 개정할 경우에 적용일자 및 개정사유를 명시하여 현행 약관과 함께 당 사이트의
초기화면에 그 적용일자 7일 이전부터 적용일자 전일까지 공지합니다. 다만, 회원에게 불리하게 약관내용을
변경하는 경우에는 최소한 30일 이상의 사전 유예기간을 두고 공지합니다. 이 경우 당 사이트는 개정 전
내용과 개정 후 내용을 명확하게 비교하여 이용자가 알기 쉽도록 표시합니다.
제 4 조(약관 외 준칙)
① 이 약관은 당 사이트가 제공하는 서비스에 관한 이용안내와 함께 적용됩니다.
② 이 약관에 명시되지 아니한 사항은 관계법령의 규정이 적용됩니다.
제 2 장 이용계약의 체결
제 5 조 (이용계약의 성립 등)
① 이용계약은 이용고객이 당 사이트가 정한 약관에 「동의합니다」를 선택하고, 당 사이트가 정한
온라인신청양식을 작성하여 서비스 이용을 신청한 후, 당 사이트가 이를 승낙함으로써 성립합니다.
② 제1항의 승낙은 당 사이트가 제공하는 과학기술정보검색, 맞춤정보, 서지정보 등 다른 서비스의 이용승낙을
포함합니다.
제 6 조 (회원가입)
서비스를 이용하고자 하는 고객은 당 사이트에서 정한 회원가입양식에 개인정보를 기재하여 가입을 하여야 합니다.
제 7 조 (개인정보의 보호 및 사용)
당 사이트는 관계법령이 정하는 바에 따라 회원 등록정보를 포함한 회원의 개인정보를 보호하기 위해 노력합니다. 회원 개인정보의 보호 및 사용에 대해서는 관련법령 및 당 사이트의 개인정보 보호정책이 적용됩니다.
제 8 조 (이용 신청의 승낙과 제한)
① 당 사이트는 제6조의 규정에 의한 이용신청고객에 대하여 서비스 이용을 승낙합니다.
② 당 사이트는 아래사항에 해당하는 경우에 대해서 승낙하지 아니 합니다.
- 이용계약 신청서의 내용을 허위로 기재한 경우
- 기타 규정한 제반사항을 위반하며 신청하는 경우
제 9 조 (회원 ID 부여 및 변경 등)
① 당 사이트는 이용고객에 대하여 약관에 정하는 바에 따라 자신이 선정한 회원 ID를 부여합니다.
② 회원 ID는 원칙적으로 변경이 불가하며 부득이한 사유로 인하여 변경 하고자 하는 경우에는 해당 ID를
해지하고 재가입해야 합니다.
③ 기타 회원 개인정보 관리 및 변경 등에 관한 사항은 서비스별 안내에 정하는 바에 의합니다.
제 3 장 계약 당사자의 의무
제 10 조 (KISTI의 의무)
① 당 사이트는 이용고객이 희망한 서비스 제공 개시일에 특별한 사정이 없는 한 서비스를 이용할 수 있도록
하여야 합니다.
② 당 사이트는 개인정보 보호를 위해 보안시스템을 구축하며 개인정보 보호정책을 공시하고 준수합니다.
③ 당 사이트는 회원으로부터 제기되는 의견이나 불만이 정당하다고 객관적으로 인정될 경우에는 적절한 절차를
거쳐 즉시 처리하여야 합니다. 다만, 즉시 처리가 곤란한 경우는 회원에게 그 사유와 처리일정을 통보하여야
합니다.
제 11 조 (회원의 의무)
① 이용자는 회원가입 신청 또는 회원정보 변경 시 실명으로 모든 사항을 사실에 근거하여 작성하여야 하며,
허위 또는 타인의 정보를 등록할 경우 일체의 권리를 주장할 수 없습니다.
② 당 사이트가 관계법령 및 개인정보 보호정책에 의거하여 그 책임을 지는 경우를 제외하고 회원에게 부여된
ID의 비밀번호 관리소홀, 부정사용에 의하여 발생하는 모든 결과에 대한 책임은 회원에게 있습니다.
③ 회원은 당 사이트 및 제 3자의 지적 재산권을 침해해서는 안 됩니다.
제 4 장 서비스의 이용
제 12 조 (서비스 이용 시간)
① 서비스 이용은 당 사이트의 업무상 또는 기술상 특별한 지장이 없는 한 연중무휴, 1일 24시간 운영을
원칙으로 합니다. 단, 당 사이트는 시스템 정기점검, 증설 및 교체를 위해 당 사이트가 정한 날이나 시간에
서비스를 일시 중단할 수 있으며, 예정되어 있는 작업으로 인한 서비스 일시중단은 당 사이트 홈페이지를
통해 사전에 공지합니다.
② 당 사이트는 서비스를 특정범위로 분할하여 각 범위별로 이용가능시간을 별도로 지정할 수 있습니다. 다만
이 경우 그 내용을 공지합니다.
제 13 조 (홈페이지 저작권)
① NDSL에서 제공하는 모든 저작물의 저작권은 원저작자에게 있으며, KISTI는 복제/배포/전송권을 확보하고
있습니다.
② NDSL에서 제공하는 콘텐츠를 상업적 및 기타 영리목적으로 복제/배포/전송할 경우 사전에 KISTI의 허락을
받아야 합니다.
③ NDSL에서 제공하는 콘텐츠를 보도, 비평, 교육, 연구 등을 위하여 정당한 범위 안에서 공정한 관행에
합치되게 인용할 수 있습니다.
④ NDSL에서 제공하는 콘텐츠를 무단 복제, 전송, 배포 기타 저작권법에 위반되는 방법으로 이용할 경우
저작권법 제136조에 따라 5년 이하의 징역 또는 5천만 원 이하의 벌금에 처해질 수 있습니다.
제 14 조 (유료서비스)
① 당 사이트 및 협력기관이 정한 유료서비스(원문복사 등)는 별도로 정해진 바에 따르며, 변경사항은 시행 전에
당 사이트 홈페이지를 통하여 회원에게 공지합니다.
② 유료서비스를 이용하려는 회원은 정해진 요금체계에 따라 요금을 납부해야 합니다.
제 5 장 계약 해지 및 이용 제한
제 15 조 (계약 해지)
회원이 이용계약을 해지하고자 하는 때에는 [가입해지] 메뉴를 이용해 직접 해지해야 합니다.
제 16 조 (서비스 이용제한)
① 당 사이트는 회원이 서비스 이용내용에 있어서 본 약관 제 11조 내용을 위반하거나, 다음 각 호에 해당하는
경우 서비스 이용을 제한할 수 있습니다.
- 2년 이상 서비스를 이용한 적이 없는 경우
- 기타 정상적인 서비스 운영에 방해가 될 경우
② 상기 이용제한 규정에 따라 서비스를 이용하는 회원에게 서비스 이용에 대하여 별도 공지 없이 서비스 이용의
일시정지, 이용계약 해지 할 수 있습니다.
제 17 조 (전자우편주소 수집 금지)
회원은 전자우편주소 추출기 등을 이용하여 전자우편주소를 수집 또는 제3자에게 제공할 수 없습니다.
제 6 장 손해배상 및 기타사항
제 18 조 (손해배상)
당 사이트는 무료로 제공되는 서비스와 관련하여 회원에게 어떠한 손해가 발생하더라도 당 사이트가 고의 또는 과실로 인한 손해발생을 제외하고는 이에 대하여 책임을 부담하지 아니합니다.
제 19 조 (관할 법원)
서비스 이용으로 발생한 분쟁에 대해 소송이 제기되는 경우 민사 소송법상의 관할 법원에 제기합니다.
[부 칙]
1. (시행일) 이 약관은 2016년 9월 5일부터 적용되며, 종전 약관은 본 약관으로 대체되며, 개정된 약관의 적용일 이전 가입자도 개정된 약관의 적용을 받습니다.