• International Journal of Highway Engineering
• /
• v.12 no.4
• /
• pp.53-60
• /
• 2010

Geogrid-reinforced asphalt pavement is a pavement type applicable to overlay for repair in addition to new construction. The geosynthetic materials are placed between the asphalt layers to stop or delay propagation of the cracking existing at lower layers and to reduce the rutting. In this study, the cracking, rutting, IRI, and deflection were investigated to compare the performance between geogrid-reinforced asphalt pavement and ordinary or polymer modified asphalt pavement. Based on field conditions, the 11 sections were classified into 3 groups; sections proper to compare, sections with restrictions to compare, sections with difficulties in comparing, and the data was statistically analyzed. Larger resistance to rutting and increased IRI were measured at the geogrid-reinforced asphalt pavement sections comparing to the ordinary or polymer modified asphalt pavement sections. However, the deflections of the pavements were similar and the resistance to the cracking could not be compared because of short pavement lives.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.29 no.5D
• /
• pp.619-625
• /
• 2009

Test constructions were performed at 3 sites to investigate ways for maximizing performance of geogrid-reinforced asphalt pavements known to reduce reflection cracking and rutting. Problems during construction operation which can affect bonding shear strength of the geogrid-reinforced asphalt pavements were defined and the construction conditions were intentionally made during the test constructions. Both immediately and 1year after the test constructions, cores were obtained from positions with good and bad construction conditions and then bonding shear strength tests were performed to be compared each other. Rules to be kept at construction sites were suggested to improve performance of the geogrid-reinforced asphalt pavements.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.26 no.5D
• /
• pp.783-796
• /
• 2006

Rut-resistance pavement is adopted to prevent pavement from plastic deformation since 1998. The objective of this paper is to investigate performance and economic efficiency between rut-resistance pavement and conventional hot-mix asphalt(HMA) on national highway. The pavement deterioration models incorporated in HDM-4 have been calibrated and adapted to local road conditions based on observed pavement rut-depth data. Based on calibration result of HDM-4, the economic evaluation including road agency cost and user cost is performed for 34 road pavement sections. Furthermore, we presented optimal timing for maintenance and performance levels subject to different budget. We found that rut-resistance pavement is performing better than conventional hot-mix asphalt in most road sections. Furthermore, we confirmed that the application of HDM-4 is useful for pavement project planning and evaluation. More investigation is needed to enlarge the scope of the pavement data and to explore more deeply socio-environmental cost and delay cost.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.14 no.12
• /
• pp.6534-6541
• /
• 2013

The aim of this study was to develop a fiber-reinforced asphalt mixture that was designed to do the following: 1) address fatigue cracks, which is a major source of damage; and 2) increase the rutting resistance. This study reports the effects of the aggregate mixture design that incorporates a dumbbell-shaped fiber. An experiment was carried out to measure the unit weights and unit weight ratios between the mixture that was compacted and the one that was not. A method to substitute a specific aggregate mixture with the dumbbell-shaped fiber was confirmed using the volume concept according to the Bailey method. The results showed that the weight of the PCS aggregate mixture that need to be replaced was 11.88g when a 0.3% reinforcing fiber was added to the 1950g mixture.

• International Journal of Highway Engineering
• /
• v.4 no.1 s.11
• /
• pp.123-134
• /
• 2002

Special pavement test sections were selected to develop a distress prediction model on asphalt pavement of National Highway. Experimental design was conducted for the selection of LTPP sections on in-service pavement(new and overlaid pavement) using several variables affecting pavement performance. Preliminary sections that satisfied the design template were chosen from the national highway database, and final selection was fixed through field inspection. The number of monitoring section is 95 including 47 overlaid pavement. A pavement distress data such as crack and rutting were collected for two years. An interim pavement performance analysis was peformed to show feasibility of performance monitoring program. Data related pavement such as traffic, weather, material characteristic and crack etc. should be collected for next project years and distress prediction model will be developed through the statistical analysis.

• International Journal of Highway Engineering
• /
• v.8 no.3 s.29
• /
• pp.163-172
• /
• 2006

This study evaluated the laboratory properties of asphalt binder and mixture modified with SPC(Sulfur Polymer Cement), which consists of sulfur as a main ingredient that is an industrial by-product made from refining process of crude oil and carbon-black as an additive. Four levels of SPC modifier ratios(0, 10, 30, 50%) were evaluated in the laboratory. Superpave(Superior Performing Asphalt Pavements) system was used to determine the PG(Performance Grade) and evaluate the property of SPC modified binder at the different temperatures. IDT(Indirect Tensile Test) was performed to evaluate the resistance of fatigue and low-temperature cracking at $10^{\circ}C\;and\;-10^{\circ}C$. Wheel-tracking test was also performed to evaluate the rutting-resistance of SPC modified asphalt mixtures. Test results showed that the more SPC modifier ratios, the better rutting-resistance and the more potential of low-temperature cracking resistance. However, SPC modifier did not show the effect on the fatigue cracking resistance.

• International Journal of Highway Engineering
• /
• v.6 no.1 s.19
• /
• pp.25-36
• /
• 2004

The total length of paved roads in Korea is 67,265 Km, and among these roads, about 40% of the national highways and 98% of local roads are paved with asphalt concrete. The major distress to asphalt pavement is rutting and fatigue crack. The permanent deformation including rutting accounts for about 75% of this distress. UTW(Ultra-Thin Whitetopping), which is known for its high-quality performance in asphalt pavement with rutting and cracking, seems to reduce maintenance costs significantly if it is used as the maintenance/repair method for domestic asphalt pavement. In the research, static load test was conducted to establish a behavior of Whitetopping under traffic and environmental condition. It showed that the effect of the thickness of the concrete layer and the temperature change was significant. In addition, the tensile strain as the wheel load position was close to interior and edge of concrete slab were increased up to 75% of maximum tensile strain. It showed that joint spacing must be considered in UTW design procedure.

• International Journal of Highway Engineering
• /
• v.12 no.2
• /
• pp.81-90
• /
• 2010

This paper describes the results of laboratory and field performance tests on the polymer modified asphalt binder and mixtures developed in this study for porous asphalt pavements. Various physical and mechanical laboratory tests including DSR and BBR tests are performed for two types of modified binders, and one type of binder is selected based on the binder testing results. Mix designs are conducted for the selected asphalt binder and a Japanese modified binder, respectively. Various performance tests including fatigue tests, wheel tracking tests, and moisture susceptibility tests are conducted for the domestic and Japanese porous asphalt mixtures. Test results indicate that the overall performance characteristics of the domestic mixture are similar to or better than those of the Japanese mixture. Based on the laboratory testing results, the domestic porous mixture is applied to a field test section. Periodic field investigations are conducted to evaluate the changes in noise level and air voids with time. The road noise analysis shows that the noise levels of the porous pavement keep increasing and, after two years, are similar to those of SMA pavements.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.26 no.1D
• /
• pp.73-79
• /
• 2006

A major purpose of this study is to develop high modulus asphalt mixtures for perpetual asphalt pavements which can save maintenance cost by increasing the design and performance periods of the pavements. Various physical and mechanical laboratory tests are performed for the high modulus asphalt binder developed in this study. The test results show that the properties of the high modulus binder are similar to those of the French high modulus binders. In addition to the binder tests, various performance tests are conducted for the high modulus and conventional mixtures. The dynamic modulus test results indicate that the dynamic modulus values of the high modulus mixtures are higher than those of the conventional mixtures by 10~15% at $5^{\circ}C$, 20~25% at $15^{\circ}C$ and 100% at $30^{\circ}C$. It is observed from the performance tests that the high modulus mixtures yield better fatigue, rutting and moisture damage performance than the conventional mixtures.

• International Journal of Highway Engineering
• /
• v.12 no.2
• /
• pp.17-23
• /
• 2010

Since the relatively stiff binder shows a higher tensile strength as well as higher rutting resistance, it is believed that the binder stiffness is an important factor for rutting and tensile strength of asphalt mixtures. The typical tensile property is measured by indirect tensile strength (ITS) test at $25^{\circ}C$ and the rutting resistance is most widely measured by wheel tracking (WT) test at $60^{\circ}C$. The deformation strength ($S_D$) is newly developed property to estimate rut resistance of asphalt concretes at $60^{\circ}C$. The ITS and $S_D$ are very simple to measure by static test techniques, but the WT is measured by repeated loading procedure which requires relatively longer time and more efforts. Since these three properties are highly dependent upon the binder stiffness, it may be possible to estimate one property from another. Therefore, this study investigate the possibility of estimating the rutting characteristics (measured by WT test) by ITS or $S_D$ test, and the ITS by $S_D$. Because of binder stiffness effect, in the WT estimation by ITS, a tendency was observed for the higher ITS mixture to have the lower rut depth, giving $R^2{\fallingdotseq}$0.6, on the average. The ITS estimation by $S_D$ showed $R^2{\fallingdotseq}$0.64, and the WT estimation by SD showed $R^2{\fallingdotseq}$0.84, which is highest correlation among the three. Therefore, it was concluded that there is relatively good possibility of estimating WT result by $S_D$, and even though $R^2$ is somewhat low, there is some correlation between WT and ITS.