• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2012.05a
• /
• pp.570-573
• /
• 2012

Performance characteristics of subscale diffuser for high-altitude simulation have been numerically investigated. The length of diffuser entrance with respect to nozzle exit diameter was changed to 0, 50, 100%, respectively. In addition, flow characteristics have been studied for various length to diameter ratio of secondary throat diffuser. As a result, the shape of plume was contracted for insufficient length of diffuser entrance. Also, if the length to diameter ratio of secondary throat diffuser were less than 7 or 8, mach disk has been formed inside the diffuser.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.38 no.4
• /
• pp.321-328
• /
• 2014

The performance characteristics of a subscale diffuser under non-reacting conditions for high-altitude simulation were numerically investigated with respect to different lengths of the secondary throat diffuser. The ratio of the length of the diffuser entrance to the nozzle exit diameter was set to 0, 50, and 100%. In addition, flow characteristics were studied for a range of length-to-diameter ratios of the secondary throat diffuser. An insufficient diffuser entrance length caused contraction of the plume immediately after the nozzle exit. When the length-to-diameter ratio was less than 8, a strong Mach disk was formed inside the diffuser, resulting in a sharp increase in pressure. In addition, flow characteristics in the diverging part of the diffuser were investigated for a range of diverging part lengths. A short diverging part may lead to abrupt pressure recovery, resulting in the possible application of mechanical load to the diffuser.

• Proceedings of the KSME Conference
• /
• 2001.06e
• /
• pp.813-818
• /
• 2001

The flow characteristics of the vaned diffuser were complicated with geometric shapes. We have studied the effects of various vaned diffuser configurations, such as divergence angles and rectangular and conical cross-section shapes. Numerical analyses are carried out for the diffuser and casing. The pressure recovery coefficient was calculated to estimate the performance of the diffuser, and then compared with the measure data. Results show that the shapes and the divergence angles of the diffuser strongly influence on the performance of the small-size turbo-compressor.

• Proceeding of EDISON Challenge
• /
• 2014.03a
• /
• pp.614-618
• /
• 2014

본 연구에서는 디퓨저의 압력회복을 높이기 위해 디퓨저 입구에 실린더를 설치하여 후류가 압력회복에 어떤 영향을 미치는지 알아보았다. 2D-Incomp-2.1-P 해석자를 이용하여 속도, 압력에 따른 유동가시화를 통해 내부유동을 분석하였고, 압력회복계수를 비교하여 디퓨저 입구에 설치된 실린더의 후류가 디퓨저 성능에 어떤 영향을 주는지 비교하였다. 그결과 실린더를 설치하였을 때 확대부에서의 박리영역이 더 작아졌고 압력회복계수가 더 높아졌다.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2003.05a
• /
• pp.19-22
• /
• 2003

Ejector-diffuser system is one of fluid machinery which can entrain the fluid in low pressure part and transport it to the higher pressure part. The conventional ejector-diffuser system has been pointed out that its overall efficiency is quite low compared with other fluid machinery since it is derived by only the pure shear stresses. In the present study, 4, 6, and 8 lobed petal nozzles with a design Mach number of 1.7 are adopted as a primary nozzle to improve the performance, and are compared with a conventional circular nozzle.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.40 no.11
• /
• pp.727-736
• /
• 2016

In this study, a high-pressure multistage pump used in the combined cycle power plants is analyzed. The pump performance characteristics (differential head and efficiency) are numerically analyzed for different shapes of the radial diffuser. The design variables selected for the radial diffuser are, number of vanes, diameter ratio ($D_4/D_3$), return channel outlet angle(${\alpha}_6$), and pressure recovery factor ($C_p$). The numerical analysis results showed that the differential head and efficiency are the highest when the diameter ratio is the highest. Further, it was observed that the differential head was lower when the return channel outlet angle was $60^{\circ}$ than when it was $90^{\circ}$, because of pre-swirl at the diffuser outlet.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.13 no.5
• /
• pp.21-28
• /
• 2009

This experimental study was performed to find the important design parameters and the starting characteristics of a supersonic exhaust diffuser. The experimental study was carried out on a scaled down model of straight cylindrical supersonic exhaust diffuser, in order to evaluate the effects of operating fluid(air, nitrogen), the diffuser inlet area over the primary nozzle throat area($A_d/A_t$), the inlet pressure of primary nozzle, diffuser length over diffuser inner diameter($L_d/D_d$) and existence or nonexistence of diffuser divergence. The test results showed that the starting pressure increased with decrease in diameter of primary nozzle, and the measured starting pressure of the diffuser had approximately 90~98% efficiency as compared with the predicted starting pressure. Also, the diffuser was started at all case, regardless of $L_d/D_d$ (above 8.4) and diffuser divergence. The result of this study can be used as an essential database for developing a simulated high-altitude facility for real-scale model.

• The KSFM Journal of Fluid Machinery
• /
• v.4 no.3 s.12
• /
• pp.21-28
• /
• 2001

The effects of diffuser shapes on the flowfields of a small-size turbo-compressor have been investigated numerically and experimentally. The optimal design of elements shapes is important to develop the high efficiency turbo-compressor. Typical range of rotating speed for a small-size turbo-compressor is 40,000-70,000rpm. Numerical analyses were conducted to the rectangular and conical shapes of diffuser Three-dimensional, steady and viscous governing equations were solved by SIMPLE algorithm. To confirm the numerical results, the experimental measurements for the static pressure and temperature at the inlet and outlet boundaries were performed. Comparisons of these results were done, and the reasonable agreements were acquired.

• Aerospace Engineering and Technology
• /
• v.7 no.1
• /
• pp.136-141
• /
• 2008

Cylindrical supersonic exhaust diffuser, which utilizes the momentum of high temperature gas exhausted from nozzle, provides simple methods for obtaining stable and low pressure around the propulsion system. Hot zone on which exhausted gas from nozzle exit impinges directly should be cooled to avoid melting of diffuser. This paper describes method and result of subscale high altitude simulation test with water cooling. Subscale gas generator with solid propellant was used for hot gas source and tap water for coolant.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2017.05a
• /
• pp.1026-1030
• /
• 2017

In this study, we propose an supersonic diffuser that is one of test facilities for hypersonic propulsion engine, and conduct numerical analyses and cold flow test using each diffuser as the corresponding variable. Specifically, inner flow characteristics are computed based on mach number and pressure by the numerical analyses. Also, we test through cold flow test the pressure in the vacuum chamber and the inner pressure that is formed by the wall pressure. Finally, we compare the results from cold flow test and the numerical analyses, and report a preliminary result that might be useful to construct a better test facility of hypersonic propulsion engine in the future.