• Korean Chemical Engineering Research
• /
• v.53 no.5
• /
• pp.584-589
• /
• 2015

For effective power generation with fuel cells in low-oxygen environments such as submarines and unmanned underwater vehicles, a hydrogen source which has a high hydrogen storage density is required. Diesel fuel is easy to storage and supply due to its liquid phase and it has a high density per unit volume and unit mass of hydrogen that required for driving the fuel cells. In this paper, diesel fuel was selected as a hydrogen source for driving the fuel cell in oxygen lean environments. In addition, the aqueous hydrogen peroxide solution was suggested as an alternative oxidant for hydrogen production through the diesel reforming reaction because of its high oxygen density and liquid phase which makes it easy to storage. In order to determine the characteristics of hydrogen peroxide as an oxidant of diesel reforming, comparative experiments were conducted and it was found that hydrogen peroxide solution has the same characteristics when reformed with oxidants of both steam and oxygen. Moreover, the commercial diesel reforming performances were analyzed according to the reaction temperature and concentration of aqueous hydrogen peroxide solution. Then, through the 49 hours accelerated degradation tests, the possibility of hydrogen production via diesel and aqueous hydrogen peroxide solution was confirmed.

• Journal of the Korean Electrochemical Society
• /
• v.10 no.2
• /
• pp.110-115
• /
• 2007

Solid oxide fuel cell(SOFC) has high fuel flexibility due to its high operating temperatures. Hydrocarbonaceous fuels such as diesel has several advantages such as high energy density and established infrastructure for fuel cell applications. However diesel reforming has technical problems like coke formation in a reactor, which results in catastrophic failure of whole system. Performance degradation of diesel autothermal reforming (ATR) leads to increase of undesirable hydrocarbons at reformed gases and subsequently degrades SOFC performance. In this study, we investigate the degradation of SOFC performance(OCV, open circuit voltage) under hydrocarbon(n-Butane) feeds and characteristics of diesel performing under various ratios of reactants($H_2O/C,\;O_2/C$ molar ratios) for improvement of SOFC performance. Especially we achieved relatively high performance of diesel ATR under $H_2O/C=0.8,\;O_2/C=3$ condition.

• Journal of the Korean Electrochemical Society
• /
• v.8 no.1
• /
• pp.12-16
• /
• 2005

Diesel is one of the best hydrogen systems, which has very high volumetric density $[kg\;H_2/m^3]\;(>100)\;and\;gravimetric\;density[\%\;H_2]\;(>\;15)$Several catalysts were selected for diesel reforming. 3 catalysts of our group (NECS-1, NECS-2, NECS-3) and 2 commercial catalysts (Sud-Chemie, Inc, FCR-HCl4, FCR-HC35) were used to reform diesel. NECS-1 showed the best performance to reform diesel. In addition to these results, we studied on reaction characteristics for better understanding about auto thermal reforming of diesel by investigating product gas concentrations and temperature Profiles along the catalyst bed. We found technological issues such as fuel delivery and thermal configuration between front exothermic part and rear endothermic part.

• Journal of Korean Society of Environmental Engineers
• /
• v.27 no.4
• /
• pp.394-401
• /
• 2005

A nonthermal plasma-assisted fuel reformer was developed and the effects of operating variables on the performance of this reformer were studied. The $H_2$-rich reformed gas from the reformer was injected into a diesel engine under an idle condition and the effects of the amount of injected gas on the NO and soot reduction were investigated. It was found that with increasing electric power consumption, the degree of facility of ignition of the reforming reaction in the reformer could be enhanced. The performance of the reformer including $H_2$ concentration, $H_2$ recovery, and energy conversion was affected only by the O/C mole ratio. This was because the equilibrium reaction temperature was governed by the O/C mole ratio. With increasing O/C mole ratio, the $H_2$ recovery and energy conversion passed through the maximum values of 33.4% and 66%, respectively, at an O/C mole ratio between 1.2 and 1.5. The reason why the $H_2$ recovery and energy conversion increased with increasing O/C mole ratio when the O/C mole ratio was lower than $1.2{\sim}1.5$ appeared to be that the complete oxidation reaction occurred more enough with increasing O/C mole ratio in this low O/C mole ratio range and accordingly the reaction temperature increased. Whereas the reason why the $H_2$ recovery and energy conversion decreased with increasing O/C mole ratio when the O/C mole ratio was higher than $1.2{\sim}1.5$ appeared to be that the complete oxidation reaction was further advanced and the $H_2$ recovery and energy conversion decreased. As the weight ratio of reformed diesel to total diesel which entered the diesel engine was increased to $18.2{\sim}23.5%$, NO and soot reduction efficiencies increased and reached as values high as 68.5% and 23.5%, respectively.

• 한국신재생에너지학회:학술대회논문집
• /
• 2009.11a
• /
• pp.218-221
• /
• 2009

Solid oxide fuel cells (SOFCs), as high-temperature fuel cells, have various advantages. In some merits of SOFCs, high temperature operation can lead to the capability for internal reforming, providing fuel flexibility. SOFCs can directly use CH4 and CO as fuels with sufficient steam feeds. However, hydrocarbons heavier than CH4, such as ethylene, ethane, and propane, induce carbon deposition on the Ni-based anodes of SOFCs. In the case of the ethylene steam reforming reaction on a Ni-based catalyst, the rate of carbon deposition is faster than among other hydrocarbons, even aromatics. In the reformates of heavy hydrocarbons (diesel, gasoline, kerosene and JP-8), the concentration of ethylene is usually higher than other low hydrocarbons such as methane, propane and butane. It is importatnt that ethylene in the reformate is removed for stlable operation of SOFCs. A new methodology, termed post-reforming was introduced for removing low hydrocarbons from the reformate gas stream. In this work, activity tests of some post-reforming catalysts, such as CGO-Ru, CGO-Ni, and CGO-Pt, are investigated. CGO-Pt catalyst is not good for removing ethylene due to low conversion of ethylene and low selectivity of ethylene dehydrogenation. The other hand, CGO-Ru and CGO-Ni catalysts show good ethylene conversion, and CGO-Ni catalyst shows the best reaction selectivity of ethylene dehydrogenation.

• Ceramist
• /
• v.15 no.3
• /
• pp.11-13
• /
• 2012

• 한국전기화학회:학술대회논문집
• /
• 2004.10a
• /
• pp.36-36
• /
• 2004

• Proceedings of the KSME Conference
• /
• 2007.05b
• /
• pp.2015-2020
• /
• 2007

Diesel is an excellent candidate fuel for fuel cell applications due to its high hydrogen density and well-established infrastructure. But, it is hard to guarantee desirable performance of diesel reformer because diesel reforming has several problems such as sulfur poisoning of catalyst and carbon deposition. We have been focusing on diesel autothermal reforming(ATR) for substantial period. It is reported that ATR of diesel has several technical advantages such as relatively high efficiency and fuel conversion compared to steam reforming(SR) and partial oxidation(POX). In this paper, we investigate characteristics of diesel reforming under various ratios of reactants(oxygen to carbon ratio, steam to carbon ratio) for improvement of reforming performances(high reforming efficiency, high fuel conversion, low carbon deposition). We also exhibit calculated heat balance of autothermal reformer at each condition to help thermal management of SOFC system.

• 한국신재생에너지학회:학술대회논문집
• /
• 2007.06a
• /
• pp.37-40
• /
• 2007

Diesel autothermal reforming(ATR) is an effective method for hydrogen production. But, diesel ATR has several problems such as the sulfur poisoning of catalyst and carbon deposition during reforming reactor. Especially, carbon deposition is a severe problem, which causes rapid performance degradation, in the reforming reaction. Ethylene among the reformate gas is a carbon precursor. Effective decomposition of ethylene is an important issue. In this paper, we investigated the carbon deposition from ethylene in the reforming reaction for proper reaction condition of diesel ATR. We achieved relatively high performance of diesel ATR under $H_{2}O/C=0.8$, $O_{2}/C=3$ condition that was based on the experiment of ethylene reforming reaction.

• Journal of ILASS-Korea
• /
• v.11 no.4
• /
• pp.234-243
• /
• 2006

Diesel autothermal reforming (ATR) is a chemical process to produce hydrogen for fuel cell applications. Several previous studies were carried out to identify technical issues in diesel reforming. It is hard to vaporize diesel due to its high boiling points. Liquid droplets of diesel result in inhomogeneous fuel mixing with other reactants such as $O_2\;and\;H_2O$, which leads to reduce the reforming efficiency and make undesired coke in reactor. To solve the fuel delivery issue, we applied an ultrasonic device as a fuel injection system. Ultrasonic injector (UI) remarkably enhanced the reforming efficiency. This paper will present the reforming results using UI. And we will discuss about atomization effects of diesel on autothermal reforming reaction.