• 한국음향학회지
• /
• 제35권3호
• /
• pp.208-215
• /
• 2016

엔진 연소 거동을 제어 및 개선하기 위하여, 연소실 내의 압력에 대한 다양한 연구가 지속적으로 수행되고 있다. 이 논문에서는 연소실 내의 압력을 통하여 디젤엔진의 연소음 레벨을 추정하였으며 이를 연소음 지수라고 정의하였다. 연소음 지수는 연소실 내의 압력신호를 고속 푸리에 변환을 통하여 계산하였으며 그 유효성을 검증하였다. 검증된 연소음 지수를 기반으로 한 제어기가 개발되었으며 차량에 탑재하였다. 연소음 지수의 목표 값을 만족시키기 위하여 일부의 분사변수를 제어하였으며 차량 연소음이 특정 주파수 영역에서 4.0 dB(A)까지 개선되었다.

• Journal of Advanced Marine Engineering and Technology
• /
• 제37권1호
• /
• pp.47-52
• /
• 2013

최근 고유가 시대를 경험한 이후 에너지 수급에 대한 불안감이 증대됨과 동시에 지구온난화, 대기오염문제 등과 관련하여 대체에너지의 개발과 고효율 친환경 기술개발에 대한 요구가 강화되고 있다. 특히, IMO(국제해사기구)의 MEPC에서는 부속서 6을 $CO_2$의 규제법으로 하고자 하는 논의가 진행 중이다. 한편, 선박의 에너지효율을 향상시키고자 하는 다양한 기술들은 대부분 주로 새로운 기술의 개발과 신조선에의 적용에만 관심이 집중되고 있다. 그러나 선박기관은 일반적으로 장시간의 운항으로 그 성능은 점점 저하되고 운전조건 또한 변화되기 때문에 운항중인 기존선의 운항조건에 최적화된 기관의 운전관리야말로 친환경 및 고효율화 대책에 실질적이면서 매우 유익한 대책이 될 수 있다. 본 논문은 선박엔진의 성능저하정도를 정량적으로 예측하고자 하는 내용으로 엔진의 성능을 저하시키는 주요 인자들과 급기효율저하, 블로바이 가스증가 및 연료분사상태의 악화로 인한 연소악화 등이 엔진성능에 미치는 영향을 예측, 검토하였다.

• 한국수산과학회지
• /
• 제9권1호
• /
• pp.74-78
• /
• 1976

연료분사시기와 회전속도를 일정하게 했을때 3종류의 연료를 사용하여 압축비와 기관의 성능관계를 조사한 결과 다음과 같은 것이 밝혀졌다. 1. 4 cycle디젤기관의 압축비는 기관마력과 연료소자율과의 관계에서 A, B, C 3종류의 연료에 대해 각각 16, 18, 19의 최적압축비가 존재했으며, 이보다 압축비를 높이면 오히려 기관성능이 저하하고 최대출력도 감소한다. 2. 매시공급열량을 일정하게 했을때 연료 A, B에 대해서 16, 18의 최적압축비가 존재했으며 연료 C에 대해서는 정할수 없었다. 따라서 저 cetane number의 연료에서는 출력에 관계없이 가장 좋은 압축비는 결정할 수 없었다. 3. 발화지연은 압축비가 높을 수록 작았고, 감소율은 압축비가 클수록 작았다.

• 대한기계학회논문집B
• /
• 제26권5호
• /
• pp.724-732
• /
• 2002

Although the demands for diesel engine is increased, our world is faced with very serious problems related to the air pollution due to the exhaust emissions of the diesel engine. In this study, the potential possibility of oxygenated fuel such as Methyl tertiary butyl ether (MTBE) was investigated for the sake of exhausted smoke reduction from diesel engine. MTBE has been used as a fuel additive blended into unleaded gasoline to improve octane number, but the study of application for diesel engine was incomplete. Because MTBE includes oxygen content approximately 18%, it is a kind of oxygenated fuel that the smoke emission of MTBE is reduced remarkably compared with commercial diesel fuel, that is, it can supply oxygen component sufficiently at high load and speed in diesel engine. But, the NOx emission of MTBE blended fuel is increased compared with commercial diesel fuel. And. it was tried to analyze not only total hydrocarbon but individual hydrocarbon components from $C_1$to $C_{6}$ in exhaust gas using gas chromatography to seek the reason for remarkable reduction of smoke emission. The results of this study show three conclusions. 1. The smoke omission of the MTBE blended fuel is lower than that of the diesel fuel at all experimental region in direct injection diesel engine. 2. Individual hydrocarbons(C$_1$~ $C_{6}$) as well as total hydrocarbon of oxygenated fuel are reduced remarkably compared with diesel fuel. 3. Smoke emission from diesel engines was strongly depended on oxygen content in fuel regardless of operating condition.

• Journal of Advanced Marine Engineering and Technology
• /
• 제30권3호
• /
• pp.351-358
• /
• 2006

The capability of high pressure injection with small fuel quantify at all engine operating conditions is one of the main feature in common rail fuel injection system, which is used in small and light-duty Diesel engine. The key parameter for the better atomized fuel sprays and multiple injections of this common rail fuel injection control, that can be freely selected irrespective of the engine speed and load is the mechanism controlling the needle energizing and movement in high pressure Diesel injector. In the electro-hydraulic injector, the injection nozzle is being opened and closed by movement of the injector's needle which is balanced by pressure between the nozzle seat and the needle control chamber. This study describes the macroscopic spray structure characteristics of the common rail Diesel injectors with different electric driving method i.e. the solenoid-driven and piezo-driven type. The macroscopic spray characteristics such as spray tip speed. spray tip penetration and spray cone angle were investigated by the high speed spray, which is measured by the back diffusion light illumination method with optical system for the high speed temporal photography in a constant volume chamber pressurized by nitrogen gas. As the results, the prototype piezo-driven injector system was designed and fabricated for the first time in domestic case and the effect of injector's needle response driven by different drive type was compared between the solenoid and piezo-driven injector It was found therefore. that the piezo-driven injector showed faster needle response and had better needle control capability by altering the electric input value than the solenoid-driven injector.

• 대한기계학회논문집B
• /
• 제26권3호
• /
• pp.498-506
• /
• 2002

Improvements of fuel properties have become essential for exhaust emission reduction as well as for optimization of directly-related design factors and exhaust gas aftertreatment. In this study, the potential possibility of oxygenated fuel such as ethylene glycol mono-n-butyl ether(EGBE) was investigated for the sake of smoke reduction from diesel engine. Because EGBE include oxygen content approximately 27%, it is a kind of effective oxygenated fuel that the smoke emission of EGBE is reduced remarkably in comparison with commercial diesel fuel, that is, it can supply oxygen component sufficient at high load and speed in diesel engine. And, it was tried to analyze the quantities of the low and high boiling point hydrocarbon among the exhaust emissions in diesel engine. It have been investigated by the quantitative analysis of the hydrocarbon $C_1$~ $C_{6}$ using the gas chromatography. This study was carried out by comparing the chromatogram with diesel fuel and diesel fuel blended EGBE 20vo1-%. The results of this study show that the hydrocarbon $C_1$~C$_{6}$ among the exhaust emission of the mixed fuels are exhausted lower than those of the diesel fuel at the all load and speed. In particular, high boiling point hydrocarbons such as $C_{5}$ and $C_{6}$ were reduced remarkably at high speed and load.d.

• 한국자동차공학회논문집
• /
• 제22권2호
• /
• pp.166-174
• /
• 2014

Fuel injection pressure has steadily increased in diesel engines for the purpose of improving fuel efficiency and cleaning exhaust gas, but it has now reached a point, where the cost for higher pressure does not warrant additional gains. Common rail systems on modern diesel engines have fuel pumps that are mechanically driven by crankshaft. The pumps actually house two pumping module inside: a low pressure pump component and a high pressure pump component. Part of the fuel compressed by the low pressure component returns to the tank in the process of maintaining the pressure in the common rail. Since the returning fuel represents pumping loss, fuel economy improves if the returned fuel can be eliminated by using a properly controled electrical fuel pump. As the first step in developing an electrical fuel pump the fuel supply system on a 6 liter diesel engine was modeled with AMESim to analyze the workload and the fuel feed rate of the injection pump, and the results served as basis for selecting a suitable servo motor and a reducer to drive the pump. A motor controller was built using a DSP and a program which controls the common rail pressure using a proportional control method based on the target fuel pressure information from the engine ECU. A test rig to evaluate performance of the fuel pump is implemented and used to show that the newly developed electrically driven fuel pump can satisfy the fuel flow demand of the engine under various operating conditions when the rotational speed of the pump is adequately controlled.

• 한국자동차공학회논문집
• /
• 제19권6호
• /
• pp.17-22
• /
• 2011

This study is to investigate the effect of the cetane number in ultra low sulfur diesel fuel on combustion characteristics and exhaust emissions at 1500 rpm and 2.6bar BMEP in low-temperature diesel combustion with 1.9L common rail direct injection diesel engine. Low-temperature diesel combustion was achieved by adopting external high EGR rate with the strategic injection control without modification of engine components. Test fuels are ultra low sulfur diesel fuel (sulfur less than 12 ppm) with two cetane numbers (CN), i.e., CN30 and CN55. For the CN30 fuel, as a start of injection (SOI) timing is retarded, the duration of an ignition delay was decreased while still longer than $20^{\circ}CA$ for all the SOI timings. In the meanwhile, the CN55 fuel showed that an ignition delay was monotonically extended as an SOI timing is retarded but much shorter than that of the CN30 fuel. The duration of combustion for both fuels was increased as an SOI timing is retarded. For the SOI timing for the minimum BSFC, the CN30 produced nearly zero PM much less than the CN55, while keeping the level of NOx and the fuel consumption similar to the CN55 fuel. However, the CN30 produced more THC and CO than the CN55 fuel, which may come from the longer ignition delay of CN30 to make fuel and air over-mixed.

• 한국자동차공학회논문집
• /
• 제14권1호
• /
• pp.68-78
• /
• 2006

In the past few years, considerable efforts have been directed towards the further development of Urea-SCR(selective catalytic reduction) technique for diesel-driven vehicle. Although urea possesses considerable advantages over Ammonia$(NH_3)$ in terms of toxicity and handling, its necessary decomposition into Ammonia and carbon dioxide complicates the DeNOx process. Moreover, a mobile SCR system has only a short distance between engine exhaust and the catalyst entrance. Hence, this leads to not enough residence times of urea, and therefore evaporation and thermolysis cannot be completed at the catalyst entrance. This may cause high secondary emissions of Ammonia and isocyanic acid from the reducing agent and also leads to the fact that a considerable section of the catalyst may be misused for the purely thermal steps of water evaporation and thermolysis of urea. Hence the key factor to implementation of SCR technology on automobile is fast thermolysis, good mixing of Ammonia and gas, and reducing Ammonia slip. In this context, this study performs three-dimensional numerical simulation of urea injection of heavy-duty diesel engine under various injection pressure, injector locations and number of injector hole. This study employs Eulerian-Lagrangian approach to consider break-up, evaporation and heat and mass-transfer between droplet and exhaust gas with considering thermolysis and the turbulence dispersion effect of droplet. The SCR-monolith brick has been treated as porous medium. The effect of location and number of hole of urea injector on the uniformity of Ammonia concentration distribution and the amount of water at the entrance of SCR-monolith has been examined in detail under various injection pressures. The present results show useful guidelines for the optimum design of urea injector for reducing Ammonia slip and improving DeNOx performance.

• 한국자동차공학회논문집
• /
• 제15권1호
• /
• pp.162-170
• /
• 2007

Currently, due to the serious world-wide air pollution by substances emitted from vehicles, emission control is enforced more firmly and it is expected that the regulation requirements for emission will become more severe. Anew concept combustion technology that can reduce the NOx and PM in relation to combustion is urgently required. Due to such social requirement, technologically advanced countries are making efforts to develop an environment-friendly vehicle engine at the nation-wide level in order to respond to the reinforced emission control. As a core combustion technology among new combustion technologies for the next generation engine, the homogeneous charge compression ignition (HCCI) is expanding its application range by adopting multiple combustion mode, catalyst, direct fuel injection and partially premixed combustion. This study used a 2-staged injection method in order to apply the HCCI combustion method without significantly altering engine specifications in the aspect of multiple combustion mode and practicality by referring to the results of studies on the HCCI engine. And it is investigated that the effects of the engine rpm and load(or A/F) to emission characteristics.