• Korean Journal of Materials Research
• /
• v.4 no.2
• /
• pp.233-240
• /
• 1994

We have investigated how the magneto-optical and recording properties of Pt/Co modulated films vary with sample preparation conditions : sputtering at various gas pressures, sputtering with Xe instead of Ar, and etching the buffer layers, etc. The magneto-optical characteristics of Pt/Co multilayers was comparable with those of currently prevailing rare-earth transition-metal alloys(Tb-Fe-Co amorphous films). On a disk of $12{\times}[Pt10.7\;{\AA}/Co2.8{\;}{\AA}]$ multilayer enhanced with 70nm silicon nitride, we have achieved a CNR of 36dB with a reading laser(${\lambda}\;=\;780nm$) power of 2.5-4.5mW for 720KHz carrier at 1.4m/s and the enhanced kerr rotation angle of $1.23^{\circ}$ at 780nm. It is suggested that Pt/Co modulated films clearly are very promising magneto-optical materials for a commercially use.

• Journal of Welding and Joining
• /
• v.33 no.3
• /
• pp.54-61
• /
• 2015

In this study, effect of laser power on hardness and microstructure of SKD61 Hot Die steel of which surface was melted and hardened with Yb:YAG disk laser was investigated. Beam speed was fixed at 70 mm/sec and distance between them was 0.8 mm about Laser surface melting. The only thing that was changed laser power. Laser powers were 2.0, 2.4 and 2.8 kW. No defect was found under all conditions. As the laser power increased, the penetration depth were deepened and the bead width was also widened. There was no hardness deviation of fusion zone at same laser power and it was higher than that of heat affected zone. In addition, the more laser power increased, the more hardness in fusion zone decreased. Fusion zone was macroscopically dendrite structure. However, core matric in dendrite was lath martensite of 100 nm size. There were $M_{23}C_6$ of 500 nm and the VC and $Mo_2C$ of a nano meters on boundary of dendrite.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.28 no.1
• /
• pp.66-71
• /
• 2004

Airborne contaminant particles are intruded into optical disk drive(ODD) due to the flow caused by disk rotation and can be adhered to objective lens, which causes read/write errors. Such a phenomenon can be a serious problem for high-density storage devices. The purpose of this paper is to understand the effect of particle contamination of objective lens in a CD-ROM drive on laser diode power and photo diode RF signal. The measurements of laser power and readout RF signal were carried out by using a laser power meter and a time interval analyzer, respectively. The parameters for estimating a readout-signal' distortion were its jitter and amplitude. Alumina(Al$_2$O$_3$) particles were used as test dust particles. The results show that the failure for data access happened as the degree of lens contamination was greater than 20％.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.36 no.3
• /
• pp.233-240
• /
• 2012

An experimental study to improve the impingement characteristics of the assist gas in laser cutting was carried out. For various assist-gas pressures, and locations and installation angles of the nozzle, the characteristics of the impingement of the jet from a supersonic rectangular nozzle were compared to those previously observed for typical circular nozzles. Schlieren flow visualizations and Pitot pressure measurements downstream of the kerf surface were utilized for this purpose. The present rectangular supersonic nozzle decreased the strength of the Mach disc occurring at the corner of the kerf surface, and thus, could weaken the separation of the assist gas on the kerf surface and increase the Pitot pressures downstream compared to conventional circular nozzles.

• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.8 no.4
• /
• pp.79-86
• /
• 1999

Electronic Speckle Pattern Interferometry(ESPI) is a powerful tool to measure the vibration mode shape and resonance frequency for modal analysis. As for ESPI this method is very suited for full-field measurement of objects in industrial areas because the interferograms are recorded with a video camera and evaluated in real-time with a computer. In this study We performed experiments at the same constraint conditions as disk brake of the practical vehicle as far as possible and obtained the resonance frequencies and vibration mode shapes by using time-averaged ESPI at once. Finally to assure the expetimental results by time-averaged ESPI we also compare those with results obtained by Laser Doppler Vibrometer and obtained good agreement.

• Journal of Sensor Science and Technology
• /
• v.22 no.1
• /
• pp.49-53
• /
• 2013

In this paper, we proposed a laser-based non-contact temperature measuring method for high speed rotating polycarbonate (PC) disk using transparency change of thermocolor. The thermocolor has abilities to change color and transparency due to a change in temperature. The thermocolor is applied on one side of polyvinylidene fluoride (PVDF) membrane. The thermocolor applied membrane is attached to inside of reaction chamber in disk. An optical system consisted of a laser beam radiator and a laser photometer is installed. Laser is irradiated at the bottom side of disk and the transmitted laser beam is detected by the laser photometer at the opposite side of disk. During the disk is rotating, laser is irradiated and detected simultaneously. The laser photometer senses the transmitted laser power and generates voltage as output. The temperature of disk can be detected during the disk is rotating up to 3000 RPM.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2005.05a
• /
• pp.264-268
• /
• 2005

In the semiconductor and optical industry the non-contact transportation is required for reducing the damages. The ultrasonic levitation is the solution of the problem. In this paper, the ultrasonic levitation system and 3 disk-type stator for levitating various object are proposed. The vibration modes of disks are analyzed with FEM and designed with the analysis results. The 3D vibration profiles of the disks are measured by Laser scanning vibrometer for verifying the vibration characteristics of the system and the amplitudes of the disks and the levitation heights of object are measured for evaluating the performance.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2005.06a
• /
• pp.1527-1530
• /
• 2005

In the semiconductor and optical industry the non-contact transportation is required for reducing the damages. The ultrasonic levitation is the solution of the problem. In this paper, the ultrasonic levitation system and 3 disk-type stator for levitation various object are proposed. The vibration modes of disks are analyzed with FEM and designed with the analysis results. The 3D vibration profiles of the disks are measured by Laser scanning vibrometer for verifying the vibration characteristics of the system. The amplitudes of the disks and the levitation heights of object are measured for evaluating the performance.

• Proceedings of the KSME Conference
• /
• 2003.04a
• /
• pp.1429-1434
• /
• 2003

A number of dust particles are intruded into ODD(Optical disk drive) due to the flow caused by disk rotation and are adhered to a lens or disk surface. The space between the disk and the lens is being reduced. Someone indicates the problems of this drive that are relatively small data storing capacity and slow access time. In recent, the problems of this optical disk drive mentioned above are being solved by adding the speed of the disk's revolution, making the actuator high-speed or light, and making the beam spot size smaller than making the space narrow between disk and lens. These particle contamination affects seriously RF Signal, readout signal in an ODD. Especially, the affected parts by a particle contamination in an ODD's readout signal are objective lens and media.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 1994.10a
• /
• pp.55-60
• /
• 1994

최근의 사무기기용 다면체반사경을 비롯하여 메모리 디스크,복사기용 드럼등은 물론 레이저 응용, X-선용의 천체망원경 및 현미경등의 광기술에 "초정밀 가공기술"의 용도가 점차 확대되어 가고 있는데, 이는 진보된 과학과 공업기술에 대한 시스템에 있어서 광학, 전기 및 전자 그리고 기계 부품의 생산에 가장 중요한 핵심기술의 하나이다. 본 연구에서는 초정밀 전용 공작기계가 아닌 범용 CNC 선반에 초정밀 절삭공구인 직선 절인의 천연다이아몬드 공구와 공작물로써 알루미늄합금을 장착하고, 선삭하여 초정밀 절삭에 관한 정성적인 데이터를 얻고자, 절삭조건에 따른 표면거칠와 절삭력 등의 변화를 조사하였다.변화를 조사하였다.