• Journal of the Korea institute for structural maintenance and inspection
• /
• v.15 no.6
• /
• pp.118-126
• /
• 2011

The objective of this paper is to study the structural behavior of Composite Basement Wall (CBW) according to shear span-to-depth ratio through an experiment and predict the nonlinear behavior of CBW by using ADINA program widely has been being used for FE analysis. Especially, this study focuses on the part of CBW in which the Reinforced Concrete (RC) is under compression stress; At the region of CBW around each floor, RC part stresses by compressive force when lateral press by soil acts on the wall. The contact condition between RC wall and steel (H-Pile) including stud connector is main factor in the analysis since it governs overall structural behavior. In order to understand the structural behavior of CBW whose RC part is under compressive stress, an experimental work and finite element analysis were performed. Main parameter in the test is shear span-to-depth ratio. For simplicity in analysis, reinforcements were not modeled as a seperated element but idealized as smeared to concrete. All elements were modeled to have bi-linear relation of material properties. Three type of contact conditions such as All Generate Option (AGO), Same Element Group Option with Tie(SEGO-T) and Same Element Group Option with Not tie(SEGO-NT) were considered in the analysis. For each analysis, the stress flow and concentration were reviewed and analysis result was compared to test one. From the test result, CBW represented ductile behavior by contribution of steel member even if it had short shear span-to-depth ration which is close to "1". The global composite behavior of CBW whose concrete wall was under compressive stress could be predicted by using contact element in ADINA program. Especially, the modeling by using AGO and SEGO-T showed more close relation on comparing with test result.

• The Journal of Engineering Geology
• /
• v.14 no.1
• /
• pp.47-60
• /
• 2004

The permeability coefficients were calculated by the homogenization analysis method with sufficient consideration of fracture geometry dependent on aperture change. According to the results of aperture measurements using a confocal laser scanning microscope, apertures on each measuring point display different magnitudes, indicating that fracture walls can not be assumed as parallel feature. After construction of fracture model based on the aperture values measured on each pressure level, the homogenization analysis was conducted to compute permeability coefficients. The calculated permeability coefficients distribute in the ranges of $10^{-1}~10^{-3}cm/sec$. Most of the specimens show decreasing permeability coefficients with the increase of the applied pressure. However, the decreasing rates of permeability coefficients do not show a constant trend on each pressure level. This phenomenon is well matched to the observation results of Chae et al. (2003). It proves that aperture change strongly influences on permeability characteristics. Three sections of each specimen have all different values of permeability coefficient. It suggests that the variation of permeability coefficient depends sensitively on aperture magnitudes and characteristics of fracture geometry. It is very important to consider accurate fracture geometries for analysis of permeability characteristics in rock fractures bearing different aperture distribution. Therefore, it needs to consider sufficiently the fracture geometries for calculating the permeability coefficients of fractures.

• Journal of Korean Society of Environmental Engineers
• /
• v.28 no.11
• /
• pp.1198-1206
• /
• 2006

We have carried out highway traffic noise prediction and measurement for 10 sites with representative road shapes and structures. A road traffic noise prediction model(NIER('99)) has been developed for environmental impact assessment in Korea. With the fitted regression analysis, the distribution ratio($R^2$) and Pearson correction coefficient(r) was 92.4% and 0.96 in $1^{st}$ floor, 38.7% and 0.66 in $3^{rd}$ floor, 42% and 0.65 in $5^{th}$ floor, 7.5% and 0.27 in $7^{th}$ floor, 28.4% and 0.53 in 10th floor, 35.6% and 0.60 in $13^{th}$ floor, 52.7% and 0.73 in $15^{th}$ floor, respectively. The measured values of the noise level except the 1st floor did not show a good agreement with the predicted noise level in the NIER('99) formula. Also, the NIER('99) formula demonstrated that the measured values weren't reasonably close to the predicted values, indicating the validity and adequacy of the predicted models with the fitted vs residual analysis in the 95% of confidence interval and 95% of predict interval. Using the equal variation on the basis of the residual vs fitted value, there was the significant difference for variation between $3^{rd}$ floor and $15^{th}$ floor except $1^{st}$ floor. The results suggested that the NIER('99) model obtained by the results according to the apartment floor must be improved and developed on the road traffic noise.

• Korean Journal of Plant Tissue Culture
• /
• v.25 no.2
• /
• pp.75-80
• /
• 1998

Disbudded epicotyl cuttings from light-grown 6-day-old seedings of Vigna angularis Owhi et Ohashi were preincubated in $2\;\times\;10^{-4}M$ IAA solution for 48 hr to promote adventitious root formation in upright or inverted direction and then incubated in upright direction for 96 hr. Adventitious root formation occurred only at the morphological base of the cuttings which were preincubated in upright direction, while at the both ends in inverted direction. IAA treatment enhanced the adventitious root formation in all cuttings regardless of their orientation during preincubation. To elucidate localized root development, the activity of enzymes involved in root initiation and development was measured 24 hr, 48 hr, and 148 hr after epicotyl incubation. IAA oxidase, peroxidase and catalase were assayed in the apical, middle and basal segment of the epicotyls, and their fresh weight and length were measured. Elongation occurred the most in the upper segment of the epicotyl while fresh weight gain was the most in the basal segment. At root initiation phase, 24 hr after incubation IAA peroxidase and catalase activities appeared high at rooting zone while IAA oxidase activity was low at both ends, IAA oxidase and peroxidase activities declined at the rooting zone during the adventitious root formation at 48 ht. Inversion of cuttings during preincubation caused a chrange of enzyme activities along their epicotyl cuttings. Only peroxidase activity showed a high correlation with root initiation. Therefore, the biochemical change is highly correlated with change in IAA level in the rooting zone of the epicotyl, resulting in root formation in unusual rooting zone of epicotyl.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.17 no.10
• /
• pp.300-309
• /
• 2016

Curved beams are increasingly used in buildings, vehicles, ships, and aircraft, which has resulted in considerable effort towards developing an accurate method for analyzing the dynamic behavior of such structures. The stability behavior of elastic curved beams has been the subject of many investigations. Solutions to the relevant differential equations have traditionally been obtained by the standard finite difference or finite element methods. However, these techniques require a great deal of computer time for a large number of discrete nodes with conditions of complex geometry and loading. One efficient procedure for the solution of partial differential equations is the differential quadrature method (DQM). This method has been applied to many cases to overcome the difficulties of complex algorithms and high storage requirements for complex geometry and loading conditions. Out-of-plane buckling of curved beams with rotatory inertia were analyzed using DQM under uniformly distributed radial loads. Critical loads were calculated for the member with various parameter ratios, boundary conditions, and opening angles. The results were compared with exact results from other methods for available cases. The DQM used only a limited number of grid points and shows very good agreement with the exact results (less than 0.3% error). New results according to diverse variation are also suggested, which show important roles in the buckling behavior of curved beams and can be used for comparisons with other numerical solutions or experimental test data.

• Proceedings of the Korea Water Resources Association Conference
• /
• 2018.05a
• /
• pp.361-361
• /
• 2018

강우패턴이 유출반응에 미치는 영향을 분석하는 것은 수문연구에서 중요한 주제 중 하나이며 댐유역에 대해 기상 및 유출자료를 사용하여 이를 상세히 분석함으로써 이수기에 필요한 수자원을 예측 및 확보하는 것은 중요하다. 강우패턴이 유출반응에 미치는 영향을 상세히 분석하기 위해서는 댐유역의 상류부터 하류까지 많은 유출관측지점의 자료를 사용해야 하지만 상류의 소유역들은 대부분 미계측유역이라는 문제점이 있다. 본 연구에서는 자료공간확장 방법을 사용하여 미계측유역의 유출자료를 생성하고 이 자료들을 분석함으로써 강우패턴이 유출반응에 미치는 영향을 자세히 분석하였다. 먼저 안동댐유역내 관측유역인 안동댐, 도산, 소천유역을 대상으로 1989년부터 2009년까지의 기간 중 20개의 사상에 대하여 분포형 모형인 GRM 모형의 적용성을 조사하였으며 전반적으로 0.5 Nash-Sutcliffe 계수 이상의 타당한 모형효율성 결과를 얻었다. 그 후 자료공간확장 방법을 사용하여 안동댐 상류에 위치한 47개의 미계측 소유역들의 유출자료를 생성하였으며 세 관측유역을 포함한 총 50개 유역의 유출자료를 연구에 사용하였다. 그리고 총 50개 유역의 평균강우량 시계열 자료를 생성하고 이동평균방법을 사용하여 이 평균강우량 자료를 강우강도-지속시간 곡선으로 변환하였다. 강우패턴과 유출반응간의 관계를 분석하기 위해 합리식의 유출계수와 강우강도비율을 사용하였으며 유출계수와 강우강도비율을 계산하기 위해 유역별 도달시간을 사용하였다. 여기서 강우강도비율은 강우강도지속시간 곡선을 사용하여 첨두강우강도를 도달시간에 해당하는 평균강우강도로 나눠준 값이다. 그리고 이 유출계수와 강우강도비율을 유역면적에 대해 도시함으로써 그 경향을 조사하였다. 그 결과 20개 사상은 유출계수, 강우강도비율과 유역면적을 사용하여 물리적으로 타당한 네 가지의 타입으로 분류될 수 있었다. 이 네 가지 타입은 강우의 이동 및 분포와 상관이 있었는데 첫번째 타입은 안동댐 유역전체에 강우가 거의 등분포하는 경우, 두 번째는 강우가 유역의 상류방향으로 이동하는 경우, 세 번째는 강우가 유역의 하류방향으로 이동하는 경우, 그리고 네 번째는 강우가 유역에 무작위로 분포하는 경우였다. 이것은 어떠한 사상에 대해서도 유출계수와 강우강도비율을 유역면적에 대해 도시함으로써 강우패턴과 유출간의 관계를 분석할 수 있다는 것을 나타낸다. 그리고 이 네 가지 타입에 대한 강우사상들의 비율은 각각 65%, 20%, 10%, 그리고 5% 였다. 이 타입별 강우사상의 비율은 향후 강우-유출관계에 의한 수자원 예측 및 확보에 활용될 수 있다.

• Korean Journal of Soil Science and Fertilizer
• /
• v.8 no.4
• /
• pp.177-181
• /
• 1975

The pot experiment was conducted primarily to clarify the relationship between lime application and they amount of potassium for the basal and top dressings on paddy rice. (Orizae sativa L. cultivar; variety Jinheung) The soils mixed with lime and without lime were separately filled in to 0.2827 a. open-bottom concretepots. The soil with lime was treated with slaked lime, at two weeks before transplanting to correct soil pH. around 7.0. The total amount of potassium 12 kilograms per 10a was applied by two or three split doses during transplanting, 19 days after transplanting and primodial stages. The results of experiment obtained are summarized as follows: 1. The application of potash in the rate of 4kg per 10a or less for basal dressing and the remaining amount of potash for top dressing at 19 days after transplanting and primodial stage or one top dressing, at primodial stage have increased the yield of paddy with increased number of panicles per hill, milliequivalent ratio of $K^-/Ca^{++}+Mg^{++}$ in leaves in the later stage of growth, number of ripened grains per panicle, and rate of grain maturity. 2. On the other hand, the greater the amount of potassium given for the basal dressing (over 4kilograms per 10a), the smaller number of tillers and panicles were resulted. And the tendency was considered chiefly due to high salt concentration at the early stage of rice growth.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.22 no.4
• /
• pp.594-600
• /
• 2021

Curved beam structures are generally used as components in structures such as railroad bridges and vehicles. The stability analysis of curved beams has been studied by a large number of researchers. Due to the complexities of structural components, it is difficult to obtain an analytical solution for any boundary conditions. In order to overcome these difficulties, the differential quadrature method (DQM) has been applied for a large number of cases. In this study, DQM was used to solve the complicated partial differential equations for buckling analysis of curved beams. The governing differential equation was deduced and solved for beams subjected to uniformly distributed radial loads. Critical loads were calculated with various opening angles, boundary conditions, and parameters. The results of the DQM were compared with exact solutions for available cases, and the DQM gave outstanding accuracy even when only a small number of grid points was used. Critical loads were also calculated for the in-plane inextensional buckling of the asymmetric curved beams, and two theories were compared. The study of a beam with extensibility of the arch axis shows that the effects on the critical loads are significant.

• Food Engineering Progress
• /
• v.15 no.3
• /
• pp.243-249
• /
• 2011

Optimum conditions to prepare a yeast extract with rice protein hydrolysates(rh) were investigated. The yeast extract was obtained at the level of 2.3 g/L from the yeast culture medium($30^{\circ}C$, 48 hr) composed of 5% rh and glucose( 3%, w/w). Within the extract, RNA was contained at the level of 188.1 mg/g and the levels of GMP and IMP as nucleotides were $650.33{\pm}48{\mu}g/g$, $69{\pm}21{\mu}g/g$, respectively. When Rrh(Residual rice protein hydrolysate by $Delvolase^{(R)}$) was supplemented into a yeast extract, the savory taste like umami of the mixture was found to increase noticeably based on the measurements by taste sensing system as well as sensory test. It is assumed that soluble peptides in Rrh could play an important role in improving the overall taste of yeast extract by enhancing its umami taste. Therefore, the yeast extract supplemented with Rrh could be used for manufacturing a high value-added natural seasoning ingredient.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.20 no.2
• /
• pp.67-75
• /
• 2019

The diaphragm used for CFT columns has a small amount of steel to be used, but has a disadvantage that welding is difficult and openings are required because the steel tube and four sides must be welded. The improved diaphragm to be examined in this study was cut into four corners by cutting the center hole for concrete filling. In the improved diaphragm, the width of the center hole is the same as that of the previous diaphragm, but the width of the diaphragm contacting the steel tube is reduced, thereby reducing the welding length by about 70% compared to the previous diaphragm. The in-plane strain of each specimen was analyzed when the same load was applied to the interior diaphragm through a simple tensile test. Using the general FEM program(ANSYS 19.2), the analysis was performed under the same conditions as the actual simple tensile test, and the load transfer between the improved diaphragm and the previous diaphragm was compared. When the width of the diaphragm is equal to or smaller than the flange width, stress is concentrated from the end of the diaphragm, and when the flange width is larger, stress is concentrated at the center.