• Journal of the Korean Society of Hazard Mitigation
• /
• v.10 no.4
• /
• pp.17-24
• /
• 2010

The hollow RC(Reinforced concrete) pier has the merit of lightweight pier compared with solid RC pier. However, the hollow RC pier shows a low ductile behavior due to brittle failure of inside concrete. To overcome this problem, the internally confined hollow reinforced concrete column has been developed. In this study, the behavior of internally confined hollow RC piers were evaluated with safety ratio, ductility, total material cost, the total weight of the pier, etc. The chosen parameters for the study are hollow ratio, thickness of internal steel tube, intervals between vertical re-bars, numbers of horizontal re-bars, and strength of concrete. As a result of parameters study, the usage of a minimum necessary thickness of the internal steel tube is the most effective.

• Journal of Korean Society of Steel Construction
• /
• v.17 no.6 s.79
• /
• pp.707-715
• /
• 2005

Corrugated webs have been used for composite prestressed concrete box girder bridges. Innovative steel plate girders using corrugated webs have been proposed. It has been found that analytical and experimental researches conducted to determine the strength of trapezoidally corrugated webs can fail with respect to three different buckling modes: local, global, and interactive shear buckling. Shear buckling capacity equations based on classical and orthotropic plate buckling theories have been proposed,but these equations show some differences. In this paper, geometric parameters that influence interactive shear buckling behavior with interaction effects are identified via extensive bifurcation buckling analysis using the finite element meth.

• Journal of the Earthquake Engineering Society of Korea
• /
• v.7 no.1
• /
• pp.1-7
• /
• 2003

The carbon composite tube can play an important role in replacing or complementing longitudinal and transverse reinforcing steels by providing ductility and strength for conventional columns. In this study, both the experimental and analytical investigations of axial behavior of large-scale square concrete columns confined by carbon composite tube are presented. The specimens are filament-wound carbon composite with 90$^{\circ}$+30$^{\circ}$, 90$^{\circ}$+45$^{\circ}$ winding angle respect to longitudinal axis of tube. The instrumented large-scale concrete-filled composite tubes(CFCT) are subjected to monotonic axial loads exerted by 10,000kN UTM. The influence of winding angle, thickness of tube on stress-strain relationships of the confined columns is identified and discussed. Proposed equations to predict both the strength and ductility of confined columns by carbon composite tube demonstrate good correlation with test data obtained from large-scale specimens.

• Journal of the Korea Concrete Institute
• /
• v.21 no.2
• /
• pp.169-178
• /
• 2009

An equation for calculating confining reinforcement amount of RC bridge columns, specified in the current bridge design codes, has been made to provide additional load-carrying strength for concentrically loaded columns. The additional load-carrying strength will be equal to or slightly greater than the resistant strength of a column against axial load, which is lost because the cover concrete spalls off. The equation considers concrete compressive strength, yield strength of transverse reinforcement, and the section area ratio as major variables. Among those variables, the section area ratio between the gross section and the core section, varying by cover thickness, is a variable which considers the strength in the compression-controlled region. Therefore, the cross section ratio does not have a large effect in the aspect of ductile behavior of the tension-controlled region, which is governed by bending moment rather than axial force. However, the equation of the design codes for calculating confining reinforcement amount does not directly consider ductile behavior, which is an important factor for the seismic behavior of bridge columns. Consequently, if the size of section is relatively small or if the section area ratio becomes excessively large due to the cover thickness increased for durability, too large an amount of confining reinforcement will be required possibly deteriorating the constructability and economy. Against this backdrop, in this study, comparison and analysis were performed to understand how the cover thickness influences the equation for calculating the amount of confining reinforcement. An equation for calculating the amount of confining reinforcement was also modified for reasonable seismic design and the safety. In addition, appropriateness of the modified equation was examined based on the results of various test results performed at home and abroad.

• Korean Journal of Materials Research
• /
• v.5 no.4
• /
• pp.468-475
• /
• 1995

활성금속 브레이징 방법으로 스테인레스 스틸과 질화규소를 접합하여 기계적 특성 및 유한요소법을 사용하여 접합체에서 발생되는 잔류응력의 크기를 조사하였다. 고강도 접합체를 제조하기 위하여 연성금속인 Cu 및 Cu/Mo 적층체를 중간재로 사용하였으며, 중간재의 두께 및 구조에 따라 접합체에서 발생되는 잔류응력의 크기 및 분포가 접합강도에 미치는 영향에 관하여 조사하였다.중간재인 Cu의 두께가 0.2mm 일대 세라믹스에 발생되는 최대 잔류응력의 크기가 급격히 감소하였으며, 최대 접합강도가 나타났다. Cu/Mo 다층 중간재를 사용한 접합체에서는 Cu/Mo 두께비가 감소할수록 접합강도는 증가되었다. 스테인레스 스틸/질화규소 접합체에서 Cu/Mo 중간재의 사용은 Cu 중간재 사용보다 접합강도를 증가시키는데 효과적이었으며, 최대 접합강도는 450Mpa 정도이었다. Cu/Mo 중간재를 사용한 접합체에서는 Mo에 최대 인장방향의 잔류응력이 발생하여 강도 측정시 Mo의 지배적인 소성변형으로 잔류응력이 감소되어 접합체의 접합강도를 향상시키는 것으로 생각된다.

• Journal of the Korea Concrete Institute
• /
• v.24 no.6
• /
• pp.705-714
• /
• 2012

Precast reinforced concrete bridge columns with hollow rectangular section were tested under cyclic lateral load with constant axial force to investigate its seismic performance. After all the precast column segments were erected, longitudinal reinforcement was inserted in the sheath prefabricated in the segments, which were then mortar grouted. Main variables of the test series were column aspect ratio, longitudinal reinforcement ratio, amount of lateral reinforcement, and location of segment joints. The aspect ratios were 4.5 and 2.5, and the longitudinal steel ratios were 1.15% and 3.07%. The amount of lateral reinforcement were 95%, 55%, 50%, and 27% of the minimum amount for full ductility design requirements in the Korean Bridge Design Code. The locations of segment joints in plastic hinge region were 0.5 and 1.0 times of the section depth from the bottom column end. The test results of cracking and failure mode, axial-flexural strength, lateral load-displacement relationship, and displacement ductility are presented. Then, safety of the ductility demand based seismic design in the Korean Bridge Design Code is discussed. The column specimens showed larger ductility than expected, because buckling of longitudinal reinforcing bar was prevented due to confinement developed not only by transverse steel but also by sheath and infilling mortar.

• Proceedings of the Computational Structural Engineering Institute Conference
• /
• 2009.04a
• /
• pp.492-495
• /
• 2009

본 논문에서는 유한대판법(Finite Strip Method, FSM)을 이용하여 복합재료로 구성된 박판구조물의 좌굴해석을 수행하였다. 유한대판법에서의 변위장은 정현곡선으로 구성된 X방향 성분과 여현곡선의 Y방향 성분으로 구성되어 있는 면내성분, 면외성분으로 횡방향으로 3차 다항식과 보 진동함수를 사용하여 구성되었다. 각 적층판의 강성을 두께방향으로 적분하여 전체 강성을 구하고 최소 포텐셜 에너지 이론을 사용하여 구한 평형방정식에 대입하여 전체 강성행렬을 구하였다. 자유도의 감소로 인한 해석시간의 단축, 입력자료 작성 및 출력이 쉬운 점들이 유한대판법을 이용한 좌굴해석의 장점이다.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2008.04a
• /
• pp.81-84
• /
• 2008

The equation, specified in current bridge design code, for calculating the confining transverse reinforcement amount of RC bridge columns has been made to provide additional load-carrying strength for concentrically loaded columns equal to or slightly greater than the strength lost when the cover concrete spalls off. However, this equation does not directly consider ductile behavior, which is an important factor for the seismic behavior of bridge columns. Consequently, if the section area is relatively small or if the section area ratio becomes excessively large due to the concrete cover thickness increased for durability, too large an amount of transverse reinforcement, which could deteriorate the constructability and economy of piers, will be required. This study intends to analyze what effects the concrete cover thickness has on the equation for determining the confining transverse reinforcement amount.

• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.33 no.2
• /
• pp.81-93
• /
• 2020

The fatigue characteristics of glass fiber reinforced plastic (GFRP) composites were studied under repeated loads using the finite element method (FEM). To realize the material characteristics of GFRP composites, Digimat, a mean-field homogenization tool, was employed. Additionally, the micro-structures and material models of GFRP composites were defined with it to predict the fatigue behavior of composites more realistically. Specifically, the fatigue characteristics of polybutylene terephthalate with short fiber fractions of 30wt% were investigated with respect to fiber orientation, stress ratio, and thickness. The injection analysis was conducted using Moldflow software to obtain the information on fiber orientations. It was mapped over FEM concerned with fatigue specimens. LS-DYNA, a typical finite element commercial software, was used in the coupled analysis of Digimat to calculate the stress amplitude of composites. FEMFAT software consisting of various numerical material models was used to predict the fatigue life. The results of coupled analysis of linear and nonlinear material models of Digimat were analyzed to identify the fatigue characteristics of GFRP composites using FEMFAT. Neuber's rule was applied to the linear material model to analyze the fatigue behavior in LCF regimen. Additionally, to evaluate the morphological and mechanical structure of GFRP composites, the coupled and fatigue analysis were conducted in terms of thickness.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.14 no.4
• /
• pp.94-101
• /
• 2010

Recently, the interest of precast concrete is increased for rapid construction in construction fields. Experimental study about the shear performance of the joint between hollow core slabs which have internal core to reduce their weight was performed. Main test variables were thickness of the topping concrete and existence of the wiremesh. Total 8 specimens including 4 in-plane shear and 4 out of plane shear were tested. Test results were analyzed in terms of cracking load, failure load, failure aspect, stiffness and ductility, and compared its design load to develop optimum design details. Test results indicated that the shear performance of the non-shrinkage mortar specimen was similar to that of 30mm thickness topping concrete specimen, and the effect of wiremesh reinforcement did not affect the failure load or stiffness of the specimens but the increase of ductility. And this paper presents the comparison results of the test results and design load to provide the optimum detail of the joint design between the hollow core slabs.