• Journal of Power System Engineering
• /
• v.10 no.2
• /
• pp.83-88
• /
• 2006

Corrosion characterization of Fe-XAl-0.3Y(X=5, 10, 14 wt%) alloys in $0.1{\sim}1N$ sulphuric acid at room temperature was studied using potentiodynamic techniques. The morphology and components of corrosion products on surface of Fe-aluminide alloys were investigated using SEM/EDX, XRD. The potentiodynamic polarization curve of alloys exhibited typical active, passive, transpassive behaviour. Corrosion potential($E_{corr}$) and corrosion current density($I_{corr}$) values of Fe-XAl-0.3Y alloys followed linear rate law. $E_{corr}$ of 10Al alloy and 14Al alloy was ten times lower than 5Al alloy. Icorr of 14Al alloy was five times lower than 5Al alloy. The passive film on the surface of Fe-5Al-0.3Y alloy was formed iron oxide. Fe-10Al-0.3Y and Fe-14Al-0.3Y alloys passive films were aluminium oxide. especially, Fe-14Al-0.3Y alloy showed good corrosion resistance in $0.1{\sim}1N$ sulphuric acid. This is attributed to the forming of protective $Al_2O_3$ oxide on the surface of Fe-14Al-0.3Y alloy.

• Journal of Advanced Marine Engineering and Technology
• /
• v.27 no.3
• /
• pp.447-452
• /
• 2003

Crevice corrosion is localized form of corrosion usually associated with a stagnant solution on the micro-environmental level. Such stagnant micro environments tend to occur in crevices (shielded areas) such as those formed under gaskets washers insulation material. fastener heads. surface deposits. disbonded coatings. threads. lap joints and clamps. Crevice corrosion is initiated by changes in located electrochemical reaction within the crevice such as a) depletion of inhibitor in the crevice b) depletion of oxygen in the crevice c) a shift to acid conditions in the crevice and d) build-up of aggressive ion species (e.g chloride) in the crevice. In this study. the mechanism of crevice corrosion for Type 430 stainless steel is investigated undercondition that the size of specimen is $15{\times}20\{times}3mm$, in 1N $H_2SO_4$ + 0.05N NaCl solution. and the artificial crevice gap size of 3 x 0.2 x 15 mm. Crevice corrosion is measured under applied potential -300mV(SCE) to the external surface. The obtained result of this study showed that 1) the induced time for initiation of crevice is 750 seconds. 2) potential of the crevice was about from -320mV to -399mV. which is lower than that of external surface potential of -300mV It is considered that potential drop in the crevice is one of mechanisms for the crevice corrosion

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2018.06a
• /
• pp.139-139
• /
• 2018

최근 자동차 산업을 중심으로 한 수송용 기기의 경량화 추세에 따라 대표적인 경량금속 소재인 알루미늄 합금에 대한 수요가 증가하고 있으며 이에 따라 알루미늄 합금 표면에 다양한 특성을 부여할 수 있는 표면개질 기술에 대한 필요성이 부각되고 있다. 알루미늄 합금의 대표적인 표면처리기술인 아노다이징과 유사한 원리로 표면에 세라믹 코팅층을 형성할 수 있는 기술인 플라즈마 전해 산화(Plasma electrolytic oxidation, PEO)가 주목을 받고 있다. PEO 코팅법은 전해액 내에 소재를 침지시키고 400 ~ 600V에 이르는 고전압을 인가시켜 마이크로 방전을 유도하여 표면에 치밀한 세라믹 층을 형성시키는 기술이다. 본 연구에서는 PEO법으로 표면 개질된 Al 합금 표면의 표면 조직 특성과 전기화학 특성을 평가하고, 코팅층 특성에 미치는 공정 변수의 영향을 분석하고자 하였다. PEO 처리를 위해 사용된 소재는 상용 Al 합금 판재(Al 5083-O)로서 $2cm{\times}2cm$로 절단하여, 에머리페이퍼로 1000번까지 연마하여 사용하였다. 시험을 위한 PEO 처리 시스템은 전해액 수조, 일정 온도 유지를 위한 열교환기와 칠러, 전원 발생을 위한 전원공급기(power supply)로 구성되었다. 전해액은 약 알칼리 수용액을 이용하였으며, 전원 공급기를 통해 시험편에 펄스 전류를 인가하였다. PEO 처리 후 시편에 대하여 SEM, EDS, XRD 등을 이용한 표면 특성 평가를 실시하였다. 또한 코팅층의 전기화학적 부식 특성 평가를 위해 해수용액에서 동전위분극실험을 실시하였다. 시험 결과, Al 합금의 PEO 처리 시 내식성은 개선되는 것으로 확인되었으며, 공정변수는 표면의 미세조직 및 전기화학적 특성에 큰 영향을 미치는 것으로 나타났다.

• Corrosion Science and Technology
• /
• v.20 no.5
• /
• pp.266-280
• /
• 2021

Since 2020, the International Maritime Organization (IMO) has updated regulations on the sulfur content to be less than 0.5% in exhaust gas emitted from ships. Accordingly, the exhaust gas post-treatment device for ships, which is SOx/NOx reduction technology, was introduced. However, the exhaust gas post-treatment device is suffering corrosion because of the harsh corrosive environment formed by sulfate and chlorine oxide through the desulfurization process. In this investigation, cyclic potentiodynamic polarization (CPDP) experiment for UNS S31603 and UNS N08367 was performed in a green death solution that simulates the environment of a desulfurization device. The corrosion rate of UNS S31603 at the highest temperature was about 3 times higher than that of UNS N83067. Also, electron microscope scan revealed corrosion type UNS N83067 presents intergranular corrosion tendency. On the other hand, UNS S31603 was observed as general corrosion. The α values of UNS N08367 at 30 ℃ and 60 ℃ were higher than those of UNS S31603, thus UNS N08367 is considered to have a higher local damage tendency. Whereas, since the α value of UNS S31603 at 90 ℃ is larger than that of UNS N08367, UNS S31603 is considered to have a higher local damage trend.

• Corrosion Science and Technology
• /
• v.20 no.6
• /
• pp.475-483
• /
• 2021

Additively manufactured titanium alloy is one of the promising materials in advanced medical industries. However, these additively manufactured alloys show corrosion properties different from those of conventional materials due to their unique microstructure. In this study, the effect of surface roughness and masking conditions on the results of the potentiodynamic polarization tests on additively manufactured or conventional Ti-6Al-4V alloys in artificial saliva solution with or without fluoride was investigated. The results showed that the corrosion potential was slightly lower with a flat cell with an O-ring than with masking tape. The corrosion rate was decreased with decreases in the surface roughness. Localized corrosion involving delamination of the surface layer occurred at 7 ~ 9 V (SSC) on the additively manufactured alloy in solution with or without fluoride when the samples were finished with 1000-grit SiC paper, whereas localized corrosion was not observed in the specimens finished with 1-㎛ alumina paste.

• Corrosion Science and Technology
• /
• v.20 no.6
• /
• pp.412-425
• /
• 2021

Because austenitic stainless steel causes localized corrosion such as pitting and crevice corrosion in environments containing chlorine, corrosion resistance is improved by surface treatment or changes of the alloy element content. Accordingly, research using cyclic potentiodynamic polarization experiment to evaluate the properties of the passivation film of super austenitic stainless steel that improved corrosion resistance is being actively conducted. In this investigation, the electrochemical properties of austenitic stainless steel and super austenitic stainless steel were compared and analyzed through cyclic potentiodynamic polarization experiment with varying temperatures. Repassivation properties were not observed in austenitic stainless steels at all temperature conditions, but super austenitic stainless steels exhibited repassivation behaviors at all temperatures. This is expressed as α values using a relational formula comparing the localized corrosion rate and general corrosion rate. As the α values of UNS S31603 decreased with temperature, the tendency of general corrosion was expected to be higher, and the α value of UNS N08367 increased with increasing temperatures, so it is considered that the tendency of localized corrosion was dominant.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.19 no.5
• /
• pp.551-556
• /
• 2018

The material normally used in hot dip galvanizing facilities is SM45C (carbon steel for mechanical structure, KS standard), mainly because of its price. During this process, the oxidation of the plating facility occurs due to the heat of the Zn fumes coming from the molten zinc. Since the cycle time of the current facilities is 6 months, much time and money are wasted. In this study, the corrosive properties of various materials (Inconel625, STS304, SM45C) were investigated by oxidation in a high temperature and Zn fumes environment. The possibility of applying the hot-dip galvanizing equipment was investigated for each material. The Zn fumes were generated by directly bubbling Ar gas into Zn molten metal in a 650 degree furnace. High-temperature, Zn fumes corrosion was conducted for 30 days. The sample was removed after 30 days and the oxidation of the surface was confirmed with EDS and SEM, and the corrosion properties were examined using potentiodynamic polarization tests.

• Journal of Power System Engineering
• /
• v.14 no.2
• /
• pp.71-77
• /
• 2010

This paper was studied on microstructure, mechanical properties and corrosion characteristics of 316L stainless steel pipe welds was fabricated by orbital welding process. S-Ar specimen was fabricated by using Ar purge gas and S-$N_2$ specimen was fabricated by using $N_2$ purge gas. Ferrite was not detected in weld metal of S-$N_2$ specimen but the order of 0.13 Ferrite number(FN) was detected in weld metal of S-Ar specimen. Oxygen and Nitrogen concentration of S-$N_2$ specimen was higher than S-Ar specimen on HAZ and inner bead. The welds microstructural characteristics of S-Ar and S-$N_2$ specimens are similar. The microvickers hardness values of S-Ar and S-$N_2$ specimens welds were similar and average values of each regions were in the range of 174~194. The microstructures of S-Ar and S-$N_2$ weld metal were full austenite by primary austenite solidification. The Solidification structures of S-Ar and S-$N_2$ weld metal were formed directional dendrite toward bead center. The potentiodynamic polarization curve of STS 316L pipe welds exhibited typical active, passive, transpassive behaviour. Corrosion current density$(I_{corr.})$ and corrosion rate values of S-Ar specimen in 0.1M HCl solution were $0.95{\mu}A/cm^2$ and $0.31{\mu}A$/year respectively. The values of S-$N_2$ specimen were $1.4{\mu}A/cm^2$ and $0.45{\mu}m$/year.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.19 no.6
• /
• pp.98-103
• /
• 2018

Many coating technologies have been developed so far to improve the corrosion resistance, strength, abrasion resistance and other surface properties of materials and equipment. Among them, the formation of CCO (CaCoO, then CCO) thin films has been studied and used in the electronic material field. One of the characteristics of CCO thin films is that it is resistant to high temperature heat. Particularly, the method of forming the CCO thin film is relatively simple, and it was judged that it could be introduced into the existing equipment. Therefore, in this study, an experiment and analysis were carried out to determine whether the coating of CCO thin films can be applied to hot dip galvanizing facilities. A CCO thin film was formed on the surface of STS304 base material and oxidized in a Zn fume atmosphere in a $650^{\circ}C$ furnace with an air atmosphere. Oxidation was carried out for 30 days, after which the shape of the CCO thin film was confirmed by SEM and its corrosivity was analyzed through a potentiodynamic polarization experiment.

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2016.11a
• /
• pp.144-144
• /
• 2016

플라즈마 전해 산화법(Plasma electrolytic oxidation)에 의해 형성된 코팅층은 특유의 기공구조로 인해 부식 환경에 노출 시 부식액의 침투가 급속히 이루어지는 단점이 있다. 이를 극복하기 위한 방법으로 유기코팅, sol-gel법, 폴리머 코팅 등에 의해 기공을 봉공(sealing)하는 방법이 제안되고 있다. 본 연구에서는 Al 합금의 플라즈마 전해 산화 처리 후 질산 세륨 수용액(Cerium nitrate solution)에 의한 봉공 효과를 확인하고자 하였다. PEO 코팅을 위한 전해액은 2g/L의 KOH와 $2g/L\;Na_2SiO_3$를 증류수에 용해시켜 준비하였다. PEO 코팅층은 Al 시편을 전해액 내에 위치시켜 양극으로 하고 STS를 음극으로 하여 $0.1A/cm^2$의 펄스 정전류밀도(주파수: 100Hz, 듀티비: 20%)를 15분 동안 인가하여 형성시켰다. 봉공을 위한 실링액은 증류수에 $0.3g/L\;H_2O_2$와 $1g/L\;H_3BO_3$를 첨가하고, $Ce(NO_3)_3$를 농도 변수로 첨가하여 준비하였으며, PEO 코팅 처리된 시편을 실링액에 침지하여 실링액의 농도와 침지시간을 달리하여 봉공을 실시하였다. 제작된 PEO 코팅층에 대해 SEM, EDS, XRD를 이용한 표면분석을 실시하였으며, 내식성을 확인하고자 동전위분극시험을 실시하였다. 연구 결과, 세륨 실링 처리된 PEO 코팅 층에서 미량의 세륨 성분이 검출되었으나, 세륨계 화합물 생성에 의한 마이크로 크기의 기공의 폐쇄는 관찰되지 않았다. 또한, 전기화학적 특성 평가 결과 실링 처리된 PEO 코팅층의 경우 Al 모재에 비해 2차수 정도 감소된 부식전류밀도를 나타내었다. 이 같은 내식성의 향상은 세륨 성분에 의한 부식 억제 효과 때문으로 판단된다.