• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 1994.10a
• /
• pp.49-54
• /
• 1994

A dynamic model for the cutting process in the end milling process is developed. This model, which describes the dynamic response of the end mill, the chip load geometry including tool runout, the dependence of the cutting forces on the chip load, is used to predict the dynamic cutting force during the end milling process. In order to predict accurately cutting forces and tool vibration, the model, which uses instantaneous specific cutting force, includes both regenerative effect and penetration effect. The model is verified through comparisons of model predicted cutting force with measured cutting forces obtained from machining experiments.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.21 no.2
• /
• pp.195-204
• /
• 2020

To help solve the problems of how to set the optimal sawing force and the optimal controller parameters for different sawing conditions, a mathematical model of a proposed sawing system was established according to the principle of sawing force control. The conventional PID control method was then used for further research of the closed-loop control of the sawing force. Finally, through simulation and experimental research, the influence rule of the controller parameters and sawing load on the control performance and the relationships between the sawing width and controller parameters (proportion coefficient) and the sawing force setting value were obtained, from which a system scheme for intelligent sawing control of a band sawing machine was proposed. The research shows that the sawing efficiency of the intelligent sawing system was 18.1 (48%) higher than that of the original sawing system when sawing a grooved section sawing material, which verifies the good control effect of the proposed scheme.

• Journal of the Korean Society for Precision Engineering
• /
• v.12 no.2
• /
• pp.87-96
• /
• 1995

The cutting force is the most important variable to understand the mechanics of ultra-precision machining. Most dynamometers, however, monitor the static cutting force only. But it is necessary to measure the dynamic cutting force to clarify the machinability of the material, the formation of the chip, chatter and the wear of the tool. In this research, measurement of the dynamic cutting force in order to clarify the machin-ability of the material, the formation of the chip, chatter and the wear of the tool has been conducted. A combined-type dynamometer which could measure the static cutting force and the dynamic cutting force by use of strain gauges and a piezo-film accelerometer has been developed. An analysis of the dynamometer also has been carried out.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.17 no.12
• /
• pp.2949-2961
• /
• 1993

Dynamic cutting process can be represented by a closed-loop0 system consisted of machine tool structure and pure cutting process. On this paper, cutting system is modeled as a six degrees of freedom system using MARV(Modified Autoregressive Vector) model in face milling, and the modeled dynamic cutting process is used to predict dynamic cutting force component. Based on the double modulation principle, a dynamic cutting force model is developed. From the simulated relative displacements between tool and workpiece the dynamic force domponents can be calculated, and the dynamic force can be obtained by superposition of the static force and dynamic force components. The simulated dynamic cutting forces have a good agreement with the measured cutting force.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.24 no.7 s.178
• /
• pp.1681-1688
• /
• 2000

A dynamic model for the prediction of surface topography in high speed end milling process is developed. In this model the effect of tool runout, tool deflection and spindle vibration were taken in to account. An equivalent diameter of end mill is obtained by finite element method and tool deflection experiment. A modal parameter of machine tool is extracted by using frequency response function. The tool deflection, spindle vibration chip thickness and cutting force were calculated in dynamic cutting condition. The tooth pass is calculated at the current angular position for each point of contact between the tool and the workpiece. The new dynamic model for surface predition are compared with several investigated model. It is shown that new dynamic model is more effective to predict surface topography than other suggested models. In high speed end milling, the tool vibration has more effect on surface topography than the tool deflection.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 1991.11a
• /
• pp.67-71
• /
• 1991

최근 기계가공의 고능률화와 고정도화를 위하여 공작기계의 고속화의 요구가 해가 갈수록 높아지고 있다. 특히 터어닝센타(Turning Center)에 있어서도 주축회전수가 1만 rpm 정도의 고속화, 고출력화와 함께 공구의 고속, 중점삭을 향한 성능향상이 진전되어가고 있으나, 기계-공작물-공구의 절삭 시스템 중에서 기계와 공작물을 연결하는 인터페이스로서, 고속화된 척의 개발이 늦어져서 기계의 고속화를 저해하는 하나의 요인으로 지적되어 지고 있다.(중략)

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.8 no.2
• /
• pp.162-170
• /
• 1984

대부분의 동적댐퍼들은 주구조물의 진동진폭을 정해진 주파수 변위내에서 최대로 줄이는 것을 목 표로 한다. 그러나 공작기계의 안정성은 시편과 공구사이의 상대변위와 절삭력에 의해 결정되는 전달함수의 최대크기에 의해서보다는 실수부분의 최소치에 의해 결정된다는 것이 잘 알려져 있 다. 본 논문에서는 이 사실에 착안하여 공작기계에서 발생하는 채터를 흡수하기 위한 최적의 댐 퍼를 설계하는 절차를 제시하고 1 자유도로 대표될 수 있는 구조물의 경우에 대하여 구체적인 방 법을 예시하였다. 종래의 최적 댐퍼의 성질을 구하는 방법에 비해 수학적인 절차가 약간 복잡해 지기는 하나 전산기를 이용하여 큰 어려움이 없이 최적의 설계자료를 얻을 수 있다. 댐퍼 질량이 정해졌을 때 감쇠율과 스프링 계수를 변수로 하는 목표함수가 하나의 식으로 유도될 수 없기 때 문 에 간단한 최적화 방법으로 이변수 황금분할법을 사용하였다. 수치적인 예를 통하여 종래의 다른 방법에 의한 결과와 비교하고 제안된 방법론의 타당성을 입증하였다.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 1992.04a
• /
• pp.28-32
• /
• 1992

The elimination of chatter vibration is necessary to improve the precision and the productivity of the cutting operation. A new mathematical model of chatter vibration is pressented in order to predict dynamic cutting force from static cutting data. Chatter vibration occurring in the tool structure of lathe is treated theoretically, considering the regenerative effect. The Stability Analysis is carried out by a two degress of freedom system. The dynamic cutting force is analytically expressed by the static cutting coefficient and the dynamic cutting coeccicient which can be determined from the cutting mechanics. The static cutting coefficient controls high speed chatter stability, while the dynamic cutting coefficient dominates low chatter stability. From above considerations, the cirtical width of cut which governs chatter stability was obtained.

• Journal of the Korean Society for Precision Engineering
• /
• v.21 no.5
• /
• pp.46-54
• /
• 2004

A cutting force model predicting the dynamic force induced by the axial vibration of it plate in face milling is introduced. When a plate face is milled, deformation in tool axial direction is considerable. Therefore, cutting forces are affected by not only inner-outer modulation in feed direction but also by axial deformation. A PTP (peak-to-peak) diagram made by the simulated dynamic force model is evaluated. The stability of the face milling process such as the chatter outset, and the stable cutting region can be simply estimated. Simulation results are compared with that of experiment.

• Journal of the Korean Society for Precision Engineering
• /
• v.11 no.4
• /
• pp.38-46
• /
• 1994

The vibration amplitude of boring bar is generally large at the tool tip, because it has the high length-diameter(L/D) ratio. A new dynamic cutting force model is presented by considering the change of shear angle under dynamic cutting. The boring bar is modelled as a cantilever with dynamic force acting at the tool end point. Based on this realistic continuous system model, the equation of motion of borring bar is solved by numerical computations. A good agreement is found between the proposed model and the experimental results.