• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.20 no.6
• /
• pp.799-804
• /
• 2011

CFRP(Carbon Fiber Reinforced Plastics) has been used many industries aerospace, automobile, medical device and building material industries, etc. Because it is lighter than other metals and has good properties, such as rigidity, strength and wear. CFRP may be cured integrity. However, it needs postprocessing similar to drilling or endmilling for shape cutting and combination of various material. In this paper, tool dynamometer and accelerometer used to signal analysis for machining properties under various cutting conditions and tool shape changes. In addition, microscope used to verify the machined CFRP surface. As the results, it was found that the cutting force and the vibration were decreased in the increasing of cutting edge (2-flute < 4-flute < composite tool), and the good machined surface can be obtained in this experiments.

• Journal of the KSME
• /
• v.19 no.3
• /
• pp.164-168
• /
• 1979

이상에서 논술한 바와 같이 금속절삭에 있어서는 절삭공구는 열의 와중의 격열한 상태하에서 작동이 이루어져야 하기 때문에 절삭유제를 분사함으로써 냉각작용으로 경도저하를 방지하고, 균체작용을 시킴으로써 열의 발생을 적게 하며 동력 소비를 감소함과 동시에 절삭면의 정밀도를 향상시킨다. 또한 절삭유제에 극압첨가제를 첨가함으로써 고체윤활을 생성케하여 용찰을 방지 하는 효과를 얻고 있다. 이 외에도 절살유제는 칩의 세척작용, 공작물과 기계의 방작용등의 효 과를 얻고 있다. 요는 절삭가공에서 절삭유제의 사용은 절삭공구의 수명을 연장하고 생산능률을 올리는 효과를 기대하는 것이라고 요약할 수 있다. 여기서 부차적으로 고려해야할 것은 절삭유 제의 토방법도 중요하다. 동일한 조건하에서는 토방법에 따라 효과가 다르다. 가장 효과적인 토 법은 공구의 앞여유면쪽으로 분사하는 것이 가장 좋으며, 칩 위에 분사하는 것이 가장 비효과 적이다. 이와 같은 절삭유제 작용과 효능을 알고 실제가공에 있어서 다소라도 도움이 되었으면 다행으로 생각하는 마음 간절하면서 끝맺는 바이다.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.20 no.4
• /
• pp.1216-1224
• /
• 1996

In the use of glass fiber reinforced plastics it is often necessary to cutting the components, but the cutting GFRP is often made difficult by the delamination of composites and the short tool life. In this paper, the machinability of GFRP by mean of tool materials and type was experimentally investigated. By proper selection of cutting tool material and type excellent machining of this workpiece is achieved. The surface quality relate closely with the feed rate and cutting tools.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.18 no.6
• /
• pp.26-32
• /
• 2019

Ball end mills used for high-speed and high-precision machining require longer machining time than flat end mills or face cutters, since the tool diameter is limited and the rigidity is reduced by the characteristics of the tool's cutting edge: at the top end of the tool, the cutting speed approaches zero and hardly removes any material. Because there is little material removal at the top end of the ball end mill, the outer cutting edge performs the majority of the work; this irregular cutting force deforms the tool and shortens its life. In this study, we attached an eddy-current sensor to a tool to measure the deformation from the cutting force and we used a tool dynamometer to measure the cutting force. We found that the change in cutting force is dependent on the change in feed rate during square-shaped processing and, as the feed rate is accelerated, the cutting force also increases. Higher cutting forces increase tool deformation.

• Journal of Power System Engineering
• /
• v.5 no.3
• /
• pp.73-79
• /
• 2001

The purpose of this investigation is experimentally to clarify the machinability and tool wear of STS 304 steel pipe material for piping. In order to determine the effects of cutting parameters and tool wear on thrust, torque, AE RMS, drilling is conducted on CNC milling machine. In this experiment, it is measured that thrust, torque, tool wear length, tool wear area and AE RMS during drilling using Hss tool. It has been found that a) During the drilling, the thrust and the torque of the STS 304 pipe are received more the effect of the feed than the spindle speed and the thrust increase with the increase of feed, b) The value of the AE RMS is been larger the effect of the cutting speed than the feed rate, and the value of the AE RMS increase with the increase of spindle speed, c) It has been found that the suitable feed in feed condition of 0.03, 0.05, 0.1, 0.15mm/rev is below 0.05mm/rev, d) The value of the AE RMS was shown a characteristic of the jump value during it was a sudden inrcrease of the tool wear. The increased character of the AE RMS value can be known an effective factor of the tool wear detection, and e) It can be quantitatively evaluated the condition of the tool according to calculate a area of the drill wear image which is obtained by a vision system.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2006.05a
• /
• pp.217-218
• /
• 2006

This paper presents an investigation on the characteristics for new micro tool dynamometer by using the ultrahigh-speed air turbine spindle. Recently, the ultrahigh-speed micro flat endmilling has been investigated actively due to request of accuracy improvement and productivity of die and mould manufacturing. To perform efficient ultrahigh-speed micro flat endmilling, evaluation of ultrahigh-speed machinability must be studied preferentially and it can be identified by investigation of cutting force. The cutting forces in ultrahigh-speed micro flat endmilling can be measured by micro tool dynamometer. But general dynamometer has low natural frequency and so is improper for measuring very high frequency cutting forces in ultrahigh-speed micro flat endmilling. In this study, the micro tool dynamometer which has very high natural frequency is newly designed.

• Journal of the Korean Society for Precision Engineering
• /
• v.16 no.5 s.98
• /
• pp.11-18
• /
• 1999

Recently high speed machining is being studied actively to reduce machining time and to improve machining precision. To perform efficient high speed machining, evaluation of high speed machinability must be studied preferentially and it can be identified by investigation of cutting force. To measure cutting forces in high speed machining, dynamometer which has high natural frequency was newly designed using 3-axes piezo force sensor. For newly designed dynamometer, calibration is conducted with sensitivity of force sensor modulated and proper preload and interference force are investigated experimently. Also, cutting force signals of newly designed dynamometer are compared with those of conventional one in high speed cutting experiment and its superiority is confirmed. Then using newly designed dynamometer, high speed machinability is evaluated about cutting force and tool wear in various cutting conditions.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.19 no.2
• /
• pp.217-224
• /
• 2009

This study aims to show the guideline to select optimal anti-vibration gloves for specific power tools to prevent hazardous vibration to human body. It is most desirable for the correct evaluation of handtransmitted vibration form the power tool handle to measure the acceleration between the handle surface and the hand palm as recommended in ISO 5349-1. First, the accurate acceleration measurement device was developed of which the thickness and weight were less than 6 mm and 12 g respectively so that it can be placed between the handle and the palm without any inconvenience during the measurement. Finally, using the device we estimated anti-vibration glove performances considering the frequency characteristics of generated vibration by the power tool.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.11 no.1
• /
• pp.13-19
• /
• 2012

In this study, ultrasonic vibration tool designed and made by using FEM analysis. And machining test was carried out in various machining conditions using ultrasonic vibration capable CNC machine. For work material, alumina ceramic ($Al_2O_3$) was used while for tool material diamond electroplated grinding wheel was used. To evaluate ultrasonic vibration effect, grinding test was performed with and without ultrasonic vibration in same machining condition. In ultrasonic mode, ultrasonic vibration of 20kHz was generated by HSK 63 ultrasonic actuator. The two grinding speeds, 1.67m/s and 3.35m/s, were applied. On the other hand, grinding forces were measured by KISTLER dynamometer.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2002.05a
• /
• pp.373-377
• /
• 2002

In the end milling operation the deflection of the cutter is an important factor affecting the accuracy of machining with implications on the selection of cutting parameters and economics of the operation. The deflection of the end mill was studied both experimentally with strain gauge, tool dynamometer, laser measuring apparatus and on a finite element model of the cutting using ANSYS software. The deflection of machining tool with various helix angles was studied with FEM simulation and experiment. ANSYS analysis performed on the finite element model of the end mill provides deflection results which agree within 15.0% with the experimental ones.