• Journal of the Society of Naval Architects of Korea
• /
• v.36 no.2
• /
• pp.105-113
• /
• 1999

This paper resents a prediction method of natural frequencies of coupled horizontal and torsional vibration of hull girder based on design sensitivity analysis in case of the changes of system parameters. The sensitivity analysis is formulated applying the direct differentiation method and transfer matrix method. In the analysis, warping, shear deformation due to torsion and the continuity condition at the connected part of open and closed hull section are considered. Using the presented method. The affection for natural frequencies by the change of system parameters, especially cargo and added mass and their centers, is numerically investigated for a real large container carrier.

• Journal of Advanced Marine Engineering and Technology
• /
• v.40 no.3
• /
• pp.185-190
• /
• 2016

Damages of the main engine aftmost bearing and the after stern tube bearing tend to increase due to misalignment. And as the shafting system becomes stiffer due to the large engine power, whereas the hull structure becomes more flexible due to optimization by using high tensile thin steel plates. And this is the reason that more sophisticated shaft alignments are required. In this study, the optimum shafting alignment calculation was carried out, considering the thermal expansion effect, exploiting the sensitivity index, which indicates the reasonable position of forward intermediate shaft bearing for shaft alignment. and as the main subject in this study, the elastic deformation on intermediate shaft and main engine bearings occurred by vertical load of shaft mass were examined thoroughly and analyzed allowable load of bearings, reaction influence numbers of all bearings. As the result, a reliable optimum shafting alignment was derived theoretically. To verify these results, they were referred to the engine maker's technical information of main engine installation and being used shafting alignment programs of both Korean Register of Shipping and Det Norske Veritas, their reliability were reviewed.

• Journal of Advanced Marine Engineering and Technology
• /
• v.39 no.6
• /
• pp.620-625
• /
• 2015

In an effort to reduce the onset of global warming, the International Maritime Organization Marine Environment Protection Committee (IMO MEPC) proposed the reduction in ship speeds as a way of lowering the proportion of carbon dioxide ($CO_2$) in the Green House Gas emissions from ships. To minimize fuel costs, shipping companies have already been performing slow steaming for their own fleets. Specifically, the slow steaming approach has been adopted for most ocean-going container lines. In addition, because of the increased marine fuel cost that is required to enable increased capacity, there is an urgent need for more advanced fuel-saving technologies. Therefore, in this present study, we propose a fuel-cost reduction method that can improve the performance of diesel engines. We introduce a predetermined amount (0.025% of the amount of fuel used) of fuel additive (oil-soluble calcium-based organometallic compound). For improved experimental accuracy, as the test subjects, we utilize a large two-stroke diesel engine installed in land plants. The loads of the test engine were classified as low, medium, and high (50, 75, and 100%, respectively). We compare the engine performance parameters (power output, fuel consumption rate, p-max, and exhaust temperature) before and after the addition of fuel additives. Our experimental results, confirmed that we can realize fuel-cost savings of at least 2% by adding the fuel additive in low load conditions (50%). Likewise, the maximum combustion pressure was found to have increased. On the other hand, we observed that there was a reduction in the exhaust temperature.

• Journal of Navigation and Port Research
• /
• v.30 no.1 s.107
• /
• pp.97-104
• /
• 2006

Recently the first stage qf construction for Busan new port emerged over the sea surface at the north container terminal site. With this, there are lot of discussions and debates on increasing the water depth at the approaching channel and mooring basin from the existing 15m to 18m by dredging work in order to be able to serve 12,000TEU containership, and at the same time, correction to the reclamation plan of hinterland at the part of Undong Bay qf the new port site. Since the attack of typhoon 'Maemi' in 2003, it is expected that the design wave parameters for coastal and harbor structures in this area would be somewhat changed and so the extreme wave condition at each terminal and tranquility of berthing area does, and therefore, it is necessary to analyze the tranquility at each berth Hence in this study, we constructed a wave model for these conditions and performed simulation together with the circulation model simulation, compared with the field data collected The result showed the increase of the harbor response throughout the basin but not severe condition However, a certain location needs to be prepared for the rough sea condition when a severe typhoon hit the site.

• Proceedings of the KWS Conference
• /
• 2009.11a
• /
• pp.92-92
• /
• 2009

조선업을 포함한 다양한 산업 분야에서 후판 강재의 수요량 증가와 함께 사용 범위 또한 폭넓게 되고 있다. 특히, 선박의 수송효율의 극대화를 위하여 컨테이너선의 대형화가 급속하게 진행되고 있으며, 2009년 현재1,300TEU 이상의 초대형 컨테이너선이 건조되고 이다. 이처럼 용접구조물의 초대형화에 따른 사용강재 또한 고강도 극후물화 되고 있다. 현재 선박에 적용중인 고강도 강재는 EH47 강재로 YP 460MPa 급의 강재가 Hatch Coamming부에 적용중에 있으며, 강재의 두께 또한 70mm 이상이다. 이러한 고강도 극후물재의 강구조물에 적용에 따른 선급협회에서는 용접부에서의 취성균열 전파에 의한 취성파괴의 위험성이 있으므로 강재의 두께를 제한하고 더욱 엄격한 파괴인성값을 요구하고 있다. 일본선급협회(NK)를 중심으로 취성균열의 정지를 위한 모재의 요구 성능등에 관한 연구들이 진행되고 있다. 이 연구의 대부분의 전제 조건은 선박의 블럭과 블럭의 조립시에 용접부가 직선형이 아닌 계단형(Butt shift)를 하는 것으로 하고 있으므로, 국내의 조선건조 공법의 현실과는 거리감이 있다. 본 연구에서는 국내 조선사에서 수행중인 직선 이음부에 대한 시공 공법에서 취성균열이 발생하여 진전 되더라도 균열을 정지 시킬 수 있는 기술에 관한 연구를 수행하였다. 균열의 진전은 대부부의 연속면에서는 정지를 시키지 못하고 직진 전파 하여서 파괴에 도달하게 된다. 따라서 뭔가의 불연속적인 면을 임의로 생성하여야 균열을 정지 시킬 수 있다. 본 연구에서는 이러한 균열의 정지 방법으로 형상적인 측면과 재료적인 측면에서 검토를 수행하였다. 형상적인 측면에서는 균열을 정지 시키고자 하는 위치에 불연속적인 면을 만들기 위하여 일정 크기의 hole을 만들어서 균열을 정지시켰으며, 재료적인 측면에서는 고인성의 용접재료를 사용하여서 취성균열이 진행하는 경로에 인성을 높은 재료를 적용하여 불연속적인 면의 생성과 함께 인성을 높여서 균열을 정지 시키는 기술을 개발하였다. 이러한 기술의 개발을 통하여 취성균열의 전파에 의한 파괴를 방지 할 수 있으며, 용접구조물의 안전성 확보를 가능하게 하였다.

• Proceedings of the Korean Institute of Navigation and Port Research Conference
• /
• 2005.10a
• /
• pp.117-124
• /
• 2005

Recently the first stage of construction for Busan new port emerged over the sea surface at the north container terminal site. With this, there are lot of discussions and debates on increasing the water depth at the approaching channel and mooring basin from the existing 15m to 18m by dredging work in order to be able to serve 12,000TEU containership, and at the same time, correction to the reclamation plan of hinterland at the part of Undong Bay of the new port site. Since the attack of typhoon 'Maemi' in 2003, it is expected that the design wave parameters for coastal and harbor structures in this area would be somewhat changed and so the extreme wave condition at each terminal and tranquility of berthing area does, and therefore, it is necessary to analyze the tranquility at each berth. Hence in this study, we constructed a wave model for these conditions and performed simulation together with the circulation model simulation, compared with the field data collected. The result showed the increase of the harbor response throughout the basin but not severe condition. However, a certain location needs to be prepared for the rough sea condition when a severe typhoon hit the site.

• Journal of Navigation and Port Research
• /
• v.48 no.3
• /
• pp.232-238
• /
• 2024

This study examines the effectiveness of Gamcheon Port's leading lights in reflecting the characteristics of ship traffic entering the port. The leading light of Gamcheon Port was proposed and installed in 1996 during the basic design process of supplementing the port's route signs for the entry and exit of 4,000 TEU container ships. Since then, it has been improved to accommodate the entry of 50,000 DWT general cargo ships and to reflect the crane height of Hanjin Pier, as a result of a review study conducted by the Busan Regional Maritime Affairs and Fisheries Administration to improve the still temperature of Gamcheon Port by relocating existing outer facilities. However, an analysis of the current characteristics of maritime traffic at Gamcheon Port reveals that maritime traffic congestion is smooth and the proportion of small and medium-sized ships under 10,000 tons is higher than that of large ships, resulting in decreased efficiency of the leading lights to respond to the entry of large ships. Nevertheless, considering the increasing CAGR of the entry ratio of ships of 30,000 tons or more by 8.45%, preparations for the anticipated increase in the proportion of large ships entering the port in the future are necessary, and it is preferable to maintain the function of the leading lights rather than demolishing the entrance to Gamcheon Port. The narrow nature of the Gamcheon Port route poses a higher risk of collision when ships entering and exiting encounter each other, which can burden the navigator. Therefore, instead of maintaining the function of the leading lights, it is possible to relocate the conduction light to reduce maintenance burden and install a direction light in its place. When installing the direction light, it is worth considering using Double Sector Lights instead of the currently installed Single Sector Lights at nearby Busan Bukhang Port, as the former can improve user satisfaction by providing a clearer middle line and reducing difficulties in distinguishing between points.

• Korean Business Review
• /
• v.11
• /
• pp.365-384
• /
• 1998

Under the rapid change of the world shipping industry, the liner shipping company in Korea should initiate the adaptation power, counterplot for survival, and continuous development. The world shipping industry is in the middle of the wave for the liberalization and openness of it. According to this change in world shipping industry, it is the fact that government policy for shipping industry should start turning its direction from the protectionism to the liberalism. Under this kinds of situations, this study firstly treated the liner shipping company and its governmental policy of Korea and Japan. Based on those studies, analysis of the liner shipping company operation and management reality was executed. Through the execution of studies, the problems which should be solved for development occurred. Furthermore, this thesis takes two way of researches of literature and actual proof for reinforcement plan of international competitiveness. This standard time period of study is set in 1993 except the irregular liner shipping company.

• The Sea:JOURNAL OF THE KOREAN SOCIETY OF OCEANOGRAPHY
• /
• v.19 no.1
• /
• pp.1-7
• /
• 2014

Butyltin compounds (BTs) were determined in surface sediment samples from Ulsan Bay in 2009 and 2011, to assess the contamination status and the effectiveness of tributylin (TBT) restriction of Korea. Dibutyltin and TBT concentrations in sediments in 2011 ranged from 19.5 to 980 and 14.2 to 1204 ng Sn $g^{-1}$ dry weight, respectively. The highest TBT concentration was found in a big shipyard complex and the next highest was found in harbor, suggesting that harbor and shipyard activities are a major contamination source of TBT in Ulsan Bay. Concentrations of BTs in Ulsan Bay sediments were significantly lower in 2009 and 2011 than that in 2003 survey previously reported, probably as a consequence of the legislative action in Korea. However, TBT concentrations in sediments still exceeded ecotoxicological values. Therefore, it will be important to monitor and reduce TBT contamination in sediments until the levels fall well below ecotoxicological levels.

• Journal of Korea Port Economic Association
• /
• v.30 no.1
• /
• pp.119-142
• /
• 2014

This study aims to evaluate the factors which affect the competitiveness of Gwangyang port, and to suggest strategies for the enhancement of its competitiveness by priority. This study inquires both 5 key rating factors: port location, port operations management, port costs, port facilities, and hinterland conditions and the priority of 14 detailed assessments through AHP method. First, the importances of main evaluation items for port competitiveness are analysed in the following orders: port location, port facilities, port costs, port operations, hinterland conditions. Second, the comprehensive importances based on the detailed evaluation properties complex weighting are identified in the following orders: connectivity with hinterland, accessibility of international harbor, incentives, the area of terminal, expertise and skills of port operations personnel, container throughput, and scale berths. Third, the strategies referring to the port location like centrality, transit, and merit on use should be actively conducted for the promotions of Gwangyang port's competitiveness, according to its international port competitiveness analysis. This study will provide both academic and policy implications with its related scholars, government, and research institutions. In addition, this will be contributed to formulating a basic theory for port competitiveness evaluation and providing a basic framework of evaluation analysis.