• Korean Journal of Optics and Photonics
• /
• v.16 no.6
• /
• pp.521-526
• /
• 2005

We assembled the optical beam director with diameter 300 mm. This consists of primary, secondary mirrors and 5 folding mirrors. Among them, the primary mirror is the most important component so that we measure any possible deformation on it at every step of assembly. Also, we developed the systematic alignment algorithm, which is essential because the number of mirrors is 7. The final wavefront error of the system is 1.9 wave rms (wave=633 nm) which is 7 times larger than we expected. The main source is the deformation of the 131ding mirrors. We expect that what we have learned from the assembly of this system would be helpful when we deal with a larger system in the future.

• Journal of Energy Engineering
• /
• v.5 no.2
• /
• pp.108-114
• /
• 1996

It is one of the most important factors to enhance the efficiency of the solar collectors by in-creasing collecting efficiency and decreasing heat loss. The pulse electrodeposition method has been involved in this study to improve characteristics of the solar selective coating on 230cm${\times}$60cm substrates and electrical efficiency of the process. The composition of the electrolyte was 280 g/$\ell$ chromic acid, 15 g/$\ell$ propionic acid, and 10 g/$\ell$ appropriate additive. 230cm${\times}$60cm copper and aluminium sheets were utilized as the substrates. It has been observed that the black chrome coatings exhibited reasonable optical properties for commercialization when the plating parameters were properly controlled; the absorptance was 0.98 and 0.97 and omittance was 0.17 and 0.23 for copper and aluminium substrate, respectively. This study implies that the pulse current electrolysis method could be applied to the large scale substrates, and the various products can be avilable after the consideration of the thermal conductivity, heat transfer efficiency and cost problems of the substrates.

• Korean Journal of Optics and Photonics
• /
• v.34 no.3
• /
• pp.117-123
• /
• 2023

The size of an optical surface can significantly affect the performance of an optical system, and high spatial frequency errors have a greater impact. Therefore, it is crucial to measure the surface figure error with high frequency. To address this, a new method called rotational prism stitching interferometer (RPSI) is proposed in this study. The RPSI is a type of stitching interferometer that enhances spatial resolution, but it differs from conventional stitching interferometers in that it does not require the movement of either the mirror tested or the interferometer itself to obtain sub-aperture interferograms. Instead, the RPSI uses a beam expander and a rotating Dove prism to select particular sub-apertures from the entire aperture. These sub-apertures are then stitched together to obtain a full-aperture result proportional to the square of the beam expander's magnification. The RPSI's effectiveness was demonstrated by measuring a 40 mm diameter spherical mirror using a three-magnification beam expander and comparing the results with those obtained from a commercial interferometer. The RPSI achieved surface testing results with nine times higher sampling density than the interferometer alone, with a small difference of approximately 1 nm RMS.

• Korean Journal of Optics and Photonics
• /
• v.25 no.6
• /
• pp.301-310
• /
• 2014

Recently, the fringe-field switching (FFS) mode in liquid crystal displays has been used mainly for high image quality and high-resolution liquid crystal displays (LCDs). In this review paper, the fundamental switching principle of the FFS mode, with its excellence over other LC modes in electro-optic performance, will be described. In addition, the development history, present technical issues, and future of the FFS LCD will be discussed.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.21 no.2
• /
• pp.197-203
• /
• 2001

Micro-defects induced by design and production failure or working environments are known as the cause of SCC(Stress Corrosion Cracking) in aged structures. Therefore, the evaluation of structural integrity based on micro-cracks is required not only a manufacturing step but also in-service term. So we introduce a new nondestructive inspection method using the magneto-optical film to detect micro-cracks. The method has some advantage such as high testing speed, real time data acquistion and the possibility of remote sensing by using of a magneto-optical film that takes advantage of the change of magnetic domains and domain walls. This paper introduces the concept of the new nondestructive inspection method using the magneto-optical film, also proves the possibility of this method as a remote testing system under oscillating load considering application on real fields by applying the method to four types of specimens.

• Korean Journal of Optics and Photonics
• /
• v.24 no.3
• /
• pp.111-119
• /
• 2013

A large aspheric mirror is a key component for large astronomical telescopes and high resolution satellite cameras. Since it is large and has an aspheric form, it is much more difficult to fabricate it compared to the similar size of spherical mirror. Especially, the opto-mechanical design and analysis is critical to reduce the deformation of mirror surface due to the external forces such as gravity or temperature change, as the mirror size is larger and lightweighting ratio is increased. The design requirements for the mirror are different depending on the particular ground and space applications because the environmental conditions are changed. In this paper, we explain the opto-mechanical design and analysis for ground and space applications that are among the most difficult to achieve among several technologies related to development of the large aspheric mirror.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.4 no.1
• /
• pp.76-82
• /
• 1994

Single crystals of Potassium Titanyl Phosphate (KTP) were grown from the flux of $K_6P_4O_13(K_6)$ using a high temperatures solution growth method. To grow the large KTP crystal without inclusion, the temperature gradient in furnace, crystal rotation, orientation of seed crystal, and the cooling rate were controled. The KTP crystals are up to $10(a){\times}28(b){\times}33(c)mm^3$ in size. We investigated the optical inhomogeneity in this KTP crystal by the SHG power measurement and TEM analysis.

• Journal of the Institute of Electronics Engineers of Korea SP
• /
• v.48 no.3
• /
• pp.1-12
• /
• 2011

Large-sized multi-touch screen is usually made using infrared rays. That is because it has technical constraints or cost problems to make the screen with the other ways using such as existing resistive overlays, capacitive overlay, or acoustic wave. Using infrared rays to make multi-touch screen is easy, but is likely to have technical limits to be implemented. To make up for these technical problems, two other methods were suggested through Surface project, which is a next generation user-interface concept of Microsoft. One is Frustrated Total Internal Reflection (FTIR) which uses infrared cameras, the other is Diffuse Illumination (DI). FTIR and DI are easy to be implemented in large screens and are not influenced by the number of touch points. Although FTIR method has an advantage in detecting touch-points, it also has lots of disadvantages such as screen size limit, quality of the materials, the module for infrared LED arrays, and high consuming power. On the other hand, DI method has difficulty in detecting touch-points because of it's structural problems but makes it possible to solve the problem of FTIR. In this thesis, we study the algorithms for effectively correcting the distort phenomenon of optical lens, and image processing algorithms in order to solve the touch detecting problem of the original DI method. Moreover, we suggest calibration algorithms for improving the accuracy of multi-touch, and a new tracking technique for accurate movement and gesture of the touch device. To verify our approaches, we implemented a table-based multi touch screen.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.7 no.3
• /
• pp.384-392
• /
• 1997

Potassium lithium niobate(KLN) single crystal for a nonlinear-optic material, which changes the wavelength of lasers, has a ferroelectric tetragonal tungsten bronze structure at room temperature. It has been very hard to get single crystals of good quality due to the cracks during cooling process. In order to investigate the composition change due to the evaporation of solution during the growth, the thermogravimetric analysis was carried out. In atmospheric condition at $1000^{\circ}C$ which is about $10^{\circ}C$ higher than the crystal growing temperature, the weight change was negligible amount of $1.46{\times}10^{-5}$g/($\textrm{cm}^2$hr). By using both the Pt plate as the nucleation site and the slow cooling method with temperature fluctuation, KLN single crystal of good quality of size 1 cm could be obtained. The phase transition temperature was $490^{\circ}C$, which was higher than that reported by other researchers of the other composition. The optical anisotropy due to the absorption of OH-band exists in the range of IR.

• Proceedings of the Korean Institute of Navigation and Port Research Conference
• /
• 2017.11a
• /
• pp.220-221
• /
• 2017

The initial light emitting diode (LED) has been used as a display device for various mechanical devices due to its low power. The development of LED technology has made it possible to express color with high power and high brightness. Therefore, it is used as a display such as a traffic signal, a large electric signboard, and an automobile display, and is also adapted as an indoor or outdoor light source such as an incandescent or a fluorescent lamp which requires the high luminance. The bulb of marine lantern, which is used for the aids to navigation, was replaced to LED. The first marine LED lantern was manufactured using multiple LEDs. However, if the optical design is renewed by the development of LED or even if a few LEDs are used, it is possible to satisfy the brightness and the light distribution required by the marine LED lantern.