• Journal of the Korea Convergence Society
• /
• v.12 no.5
• /
• pp.17-22
• /
• 2021

Eco-friendly magnesium-air battery is a kind of metal-air battery known as a primary battery with a very high theoretical discharge capacity. This battery is also called a metal-fuel cell from the viewpoint of using oxygen in the atmosphere as a cathode active material and magnesium alloy as a fuel. Since battery performance is determined by the properties of the magnesium alloy used as a anode, more research and development of the magnesium alloy electrode as a anode material are required in order to commercialize it as a high-performance battery. In this study, the commercialized magnesium alloys(AZ31, AZ61) were selected and then electrochemical measurements and discharge test were conducted. Electrochemical properties of magnesium alloys were investigated by OCP changes, Tafel parameters and CV measurement, and the feasibilities of AZ61 alloy with excellent discharge capacity(1410mAhg^-1) as electrode materials were evaluated through CC discharge experiments.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2011.02a
• /
• pp.57-58
• /
• 2011

III-V족 화합물 반도체의 일종인 InSb는 77 K에서 0.23 eV의 작은 밴드 갭을 가지며 높은 전하 이동도를 가지고 있기 때문에 대기권에서 전자파 흡수가 일어나지 않는 3~5 ${\mu}m$범위의 장파장 적외선 감지가 가능하여 중적외선 감지 소자로 이용되고 있다. 하지만 InSb는 밴드 갭이 매우 작기 때문에, 소자 제작시 누설전류에 의한 소자 특성의 저하가 문제시 되고 있다. 또한 다른 화합물 반도체에 비해 녹는점이 낮고, 휘발성이 강한 5족 원소인 Sb의 승화로 기판의 화학양론적 조성비(stoichiometry)가 변하기 쉬워, 계면특성 저하의 원인이 된다. 따라서 우수한 특성을 가지는 적외선 소자의 구현을 위해서, 저온에서 계면 특성이 우수한 고품질의 절연막 증착 연구가 필수적이다. 본 연구에서는 InSb 기판 위에 $SiO_2$, $Si_3N_4$의 절연막 형성시 증착온도의 변화에 따른 계면 트랩 밀도를 분석하였다. $SiO_2$, $Si_3N_4$ 절연막은 플라즈마 화학 기상 증착법(PECVD)을 이용하여 n형 InSb 기판 위에 증착하였으며, 증착온도를 $120^{\circ}C$부터 $240^{\circ}C$까지 변화시켰다. Metal oxide semiconductor(MOS) 구조 제작을 통하여, 커패시턴스-전압(C-V)분석을 진행하였으며, 절연막과 InSb 사이의 계면 트랩 밀도를 Terman method를 이용하여 계산하였다[1]. 또한, $SiO_2$와 $Si_3N_4$의 XPS 분석과 TOF-SIMS 분석을 통하여 계면 트랩 밀도의 원인을 밝혀 보았다. $120{\sim}240^{\circ}C$ 온도 범위에서 계면 트랩 밀도는 $Si_3N_4$의 경우 $2.4{\sim}4.9{\times}10^{12}cm^{-2}eV^{-1}$, $SiO_2$의 경우 $7.1{\sim}7.3{\times}10^{11}cm^{-2}eV^{-1}$ 값을 나타냈고, 두 절연막 모두 증착 온도가 증가할수록 계면 트랩 밀도가 증가하는 경향을 보였다. 그러나 모든 샘플에서 $Si_3N_4$의 경우, flat band voltage가 음의 전압으로 이동한 반면, $SiO_2$의 경우, 양의 전압으로 이동하는 것을 확인할 수 있었다. 계면 트랩 밀도 증가의 원인을 확인하기 위해서, oxide를 $120^{\circ}C$, $240^{\circ}C$에서 증착시킨 샘플을 XPS 분석을 통하여 깊이에 따른 성분분석을 하였고, 그 결과, $240^{\circ}C$에서 증착된 샘플에서 계면에서 $In_2O_3$와 $Sb_2O_3$ 피크의 증가를 확인하였다. 이는 계면에서 oxide양이 증가함을 의미하며, 이렇게 생성된 oxide는 계면 트랩으로 작용하므로, 계면 특성을 저하시키는 원인으로 작용함을 알 수 있었다. Nitride 절연막을 증착시킨 샘플은 TOF-SIMS 분석을 통해, 계면에서의 성분 분석을 하였고, 그 결과, $240^{\circ}C$에서 증착된 샘플에서 In-N, Sb-N, Si-N 결합의 감소를 확인하였다. 이렇게 분해된 결합들의 dangling 결합이 늘어 계면 트랩으로 작용하므로, 계면 특성을 저하시키는 원인으로 작용함을 알 수 있었다. 최종적으로, 소자특성을 확인 하기 위하여 계면 트랩 밀도가 가장 낮게 측정된 $200^{\circ}C$ 조건에서 $SiO_2$ 절연막을 증착하여 InSb 적외선 소자를 제작하였다. 전류-전압(I-V) 분석 결과 -0.1 V에서 16 nA의 누설 전류 값을 보였으며, $2.6{\times}10^3{\Omega}cm^2$의 RoA(zero bias resistance area)를 얻을 수 있었다. 절연막 증착조건의 최적화를 통하여, InSb 적외선 소자의 특성이 개선됨을 확인할 수 있었다.

• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.20 no.1
• /
• pp.49-59
• /
• 1984

Optimizing investigation of characteristics of underwater welding by a gravity type arc welding process was experimentally carried out by using six types of domestic coated welding electrodes for welding of domestic marine structural steel plates (KR Grade A-1, SWS41A, SWS41B,) in order to develop the underwater welding techniques in practical use. Main results obtained are summarized as follows: 1. The absorption speed of the coating of domestic coated lime titania type welding-electrode became constant at about 60 minutes in water and it was about 0.18%/min during initial 8 minutes of absorption time. 2. Thus, the immediate welding electrode could be used in underwater welding for such a short time in comparison with the joint strength of in-atmosphere-and on-water-welding by dry-, wet-or immediate-welding-electrode. 3. By bead appearance and X-ray inspection, ilmenite, limetitania and high titanium oxide types of electrodes were found better for underwater-welding of 10 mm KR Grade A-1 steel plates, while proper welding angle, current and electrode diameter were 6$0^{\circ}C$, above 160A and 4mm respectively under 28cm/min of welding speed. 4. The weld metal tensile strength or proof stress of underwater-welded-joints has a quadratic relationship with the heat input, and the optimal heat input zone is about 13 to 15KJ/cm for 10mm SWS41A steel plates, resulting from consideration upon both joint efficiency of above-100% and recovery of impact strength and strain. Meanwhile, the optimal heat input zone resulting from tension-tension fatigue limit above the base metal's of SWS41A plates is 16 to 19KJ/cm. Reliability of all the empirical equations reveals 95% confidence level. 6. The microstructure of the underwater welds of SES41A welded in such a zone has no weld defects such as hydrogen brittleness with supreme high hardness, since the HAZ-bond boundary area adjacent to both surface and base metal has only Hv400 max with the microstructure of fine martensite, bainite, pearlite and small amount of ferrite.

• Journal of the Korean Vacuum Society
• /
• v.22 no.2
• /
• pp.55-65
• /
• 2013

Sterilization of Neurospora crassa has been investigated in this research by using a surface air plasma with dielectric barrier discharged (DBD) structure under atmospheric pressure. The sinusoidal alternating current has been used in this experiment with discharge voltage of 1.4~2.3 kV. The phase difference between the voltage and current signals are found to be almost 80 degree due to the capacitive property of dielectric barrier. Temperature on the biomaterials has been minimized by radiating the heat with the air cooling system. It is noted that the substrate temperature remains under 37 degree for plasma exposure time of 10 minutes with operation of cooler system. It is found that the ozone, $O_3$, has been measured to be about 25~30 ppm within 1 cm region and to be about 5 ppm at the 150 cm downstream region away from the suface plasma. It is also noted that the nitric oxide, NO, and nitric dioxide, $NO_2$, are not nearly detected. Germination rate and mitochodrial activity of Neurospora crassa immersed in the deionized water have been found to be drastically decreased as the plasma treatment time and its electrical power are increased in this experiment. Here, the mitochondrial activity has been analyzed by MTT (3-(4,5-dimethy lthiazol-2yl)-2,5-diphenyl-2H-tetrazolium bromide) assay. However, sterilization of Neurospora crassa immersed in the Vogel's minimal media has been found to be low by plasma treatment, which is caused by surrounding background solution. This research shows the sterilization possibility of Neurospora crassa by using the noncontated surface DBD plasma, which is different from the plasma jet. This is mainly attibuted to the reactive species generated by the surface plasma, since they play a major role for inhibition of micobes such as Neurospora crassa.

• Journal of Advanced Navigation Technology
• /
• v.11 no.3
• /
• pp.239-251
• /
• 2007

This thesis is about the reduction of the power consumption in GPS embedded terminals with periodic position fix to improve the time delay of position determination. In order to improve time delay of position determination during the wireless terminal is powered on, it needs to be set such that it can be periodically recalibrated by the GPS and those recalibrated values need to be saved in the terminal's memory so that it can reduce the time delay from the request of location. By using the trace of the information that's been saved in the terminal's memory, it can be set so that it'll be easier to determine whether the wireless terminal has gone into buildings and have the capability of checking if it has gone into a specific building. Likewise, while the terminal is turned on, in order calibrate the location, it needs to continuously work the GPS engine which leads to a rapid decrease in terminal's idle time. This thesis proposes some solutions regarding these issues - reducing 20 ~ 30% of the battery consumption for GPS visible situation that can occur when the wireless terminal periodically calibrates its location to determine the in-building status, and extending the idle time of the terminal by flexibly using the suggested GPS calibration time method according to wireless terminal's mobility.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.23 no.7
• /
• pp.1-8
• /
• 2019

The primary purposes of this study are to understand a fundamental effects of electro-deposition on reinforcing steel in saturated Ca(OH)2 electrolyte, and evaluate the corrosion rates of rebars under cyclic 3wt.%NaCl immersion and dry corrosion environment. The three cement mortar specimens with cover thickness 5, 10 and 30mm, were prepared in the experiment. To monitor the corrosion rates of rebars in mortar, the three cement mortar specimens were exposed to 110 wet-drying cycles(8-hour-immersion in 3wt.%NaCl and 16-hour-drying in a room temperature) in the laboratory. During the wet-dry cycles, the polarization resistance, Rp, and solution resistance, Rs, were continuously measured. The instantaneous corrosion rates of rebars on the effect of electro-depositing with sat. Ca(OH)2 electrolyte were estimated from obtained R-1p and degrees of wetness were estimated from Rs values. From the experimental results, the corrosion rates of rebars were greatly accelerated by wet/dry cycles. During the mortars exposed to drying condition, the large increases in the corrosion rates were showed at all rebar surfaces in three mortar specimen, attributed from the accelerated reduction rates of dissolved oxygen in drying process. However, the corrosion rates on rebar surface electrochemically deposited with sat. Ca(OH)2 electrolyte showed the clear decreases, caused by calcium deposits in the porous rust layer.

• Korean Journal of Environmental Agriculture
• /
• v.18 no.2
• /
• pp.179-184
• /
• 1999

To examine the relationship between air pollution and occurrence of disease in plants, we investigated the alteration of physiology and biochemistry of Ginkgo biloba by inoculating with Coniothyrium sp. and fumigating with 0.1 ${\mu}l/l\;SO_{2-}$ Visual damage did not appear but photosynthesis, $CO_2$ use efficiency(CUE) and water use efficiency(WUE) were reduced when G. biloba was exposed to $SO_{2-}$for 7days (8 hours a day). When inoculated with Coniothyrium sp., the seventies of damage in G. biloba showed a threefold difference between $SO_{2-}$ treatment (SI) and $SO_{2-}$ free treatment (SFI) at day 42 from initial inoculation. Little difference was observed in sugar contents that may be used pathogens feed, among control, SFI and SI. In spite of the reduction in photosynthetic rate, sugar contents and CUE were maintained. WUE was enhanced 13% more at SI than SFI. The $CO_2$fixation boosted because of enhanced WUE, and thus sugar synthesis was not affected. In addition, sugar transport seems to be retarded for some internal alteration. Consequently, the severity of SI was more serious than that of SFI because Coniothyrium sp. easily invades into the physical texture of G. biloba weakened by $SO_2$ fumigation and because sugar was accumulated in leaves of G. biloba.

• Proceedings of the Korean Powder Metallurgy Institute Conference
• /
• 2002.04b
• /
• pp.45-45
• /
• 2002

나노미터 크기의 결정립을 가지는 나노분말 및 나노복합분말의 제조와 특성에 관한 연구가 매우 활발하다. 나노복합분말의 제조방법에는 기상증발후 응축법, 화학응축법, 기계적합금법 등이 있으나, 고순도 및 균일한 크기분포의 분말과 응집되지 않은 분말의 제조 조건을 가장 잘 만족하는 방법은 화학기상응축법(Chemical Vapor Condensation; CVC)이다. 본 연구그룹 에서는 CVC밤법으로 이용하여 공구/금형재료에 가장 많이 사용되는 WC/Co 합금의 결정립을 n nm크기로 극미세화고자하는 연구을 진행하고 있다. 본 연구에서는 이들 WC/Co합금제조시 가장 중요한 출발분말인 나노크기 WC 분말의 제조와 그 특성에 관하여 연구하고자 하였다. 나노미터 WC분말을 제조하기 의한 전구체는 고상의 금속유기물인Tungstenhexacarbonyl$(W(CO)_6)$ 을 사용하였다. 수평관상로을 반응기로 사용하였으며, 노내의 온도을 500-110$0^{\circ}C$로 변화시 키면서 WC 분말을 합성하였다. 반응기 및 포집기 내부를 대기분위기, 상압의 Ar분위기, 진공 분위기로 변화시켜 압력 및 분위기의 영향을 조사하였다. 포집기는 상온 및 액체질소로 냉각 한 Chiller을 사용하였다. 형성분말의 상분석은 XRD로 조사하였으며, 형태 및 결정립크기는 TEM로 분석하였다. 반응온도 600 -1 OOO$^{\circ}C$의 온도범위에서 검은색의 WC 분말이 제조되었다. XRD 분석의 결과 로 제조된 분말은 상온에서 준안정상인 Hexagonal 구조의 $\gammar-WC_{1-x}$ 상이였으며, TEM 분석결 과 상압하에서는 약 30nm이하의 WC분말이 제조되었으며, 그 형태는 둥근 4각형의 모양을 지녔다. 감압하에서 진행한 경우 결정립의 크기는 8nm이하를 가졌다.곤가스로 산화를 방지하였고, 냉매로는 질소가스를 이용하였다. 제조된 분말을 기ㅖ적 분급법을 이용하여 분급하였고, 냉매로는 질소가스를 이용하였다. 제조된 분말을 기계적 분급ㅂ법을 이용하여 분급하였고, 압출에 이용된 분말은 250$\mu\textrm{m}$이하의 크기를 사용하였다. 또한 분말제조과정 중 형성되는 표면산화층을 제거하기 위하여 36$0^{\circ}C$에서 4시간동안 수소 환원처리를 행하였다. 제조된 분말은 열간 압출을 위하여 Aㅣcan에 넣고 냉간성형체를 만들고, 진공처리를 한 후 밀봉하여 탈가스처리를 하였다. 압출다이는 압출비가 각각 28:1과 16:1인 평다이(9$0^{\circ}C$)를 사용하여 각각 내경이 9, 12cm이고, 길이가 50, 30cm인 압출재를 제조하였다. 열간압출한 후의 미세조직을 광학현미경으로 압출방향에 평행한 방향과 수직방향으로 관찰하였고, 열간 압출재 이방성을 검토하기 위하여 X선 회절분석을 실실하여 결정방위를 확인하였다. 전기 비저항 및 Seebeck 계수 측정을 위하여 각각 2$\times$2$\times$10$mm^3$ 그리고 5$\times$5$\times$10TEX>$mm^3$ 크기의 시편을 준비하였다.준비하였다.전류를 구성하는 주요 입자의 에너지 영역(75~l13keV)에서 가장 높은(0.80) 상관계수를 기록했다. 넷째, 회복기 중에 일어나는 입자들의 유입은 자기폭풍의 지속시간을 연장시키는 경향을 보이며 큰 자기폭풍일수록 현저했다. 주상에서 관측된 이러한 특성은 서브스톰 확장기 활동이 자기폭풍의 발달과 밀접한 관계가 있음을 시사한다.se that were all low in two aspects, named "the Nonsign

• Resources Recycling
• /
• v.11 no.6
• /
• pp.3-11
• /
• 2002

Recently, waste printed circuit board (PCB) has significantly increased in its amount due to the rapid development of electronic industries. Since several kinds of noxious materials and also valuable metals are contained in it, the waste PCB is in an urgent need of recycling for the dual purposes for the prevention of environmental pollution and recovery of valuable resources. Also, the catalyst which equipped in the exhaust pipes of automobiles to reduce emission of air pollutants contains precious met-als so that their recovery from the waste auto-catalysts is required. In this study, the recovery of valuable metals from waste PCB and auto-catalyst by arc furnace melting process has been investigated, which is known to be very stable and suitable f3r less production of pollutants due to its high operating temperature. The effect of the kind of flux on the recovery of precious metals was examined by using quicklime, converter slag, and copper slag as the flux. In addition, the influence of direct and alternating current and the applying direction of direct current has been investigated. It was observed that using converter or copper slag as a flux was more desirable for a higher efficiency in the precious metal recovery compared with quicklime. For the effect of current, application of direct current taking the bottom as a negative pole generally showed a better efficiency for the extraction of valuable metals from waste PCB, which was also observed for the case of waste auto-catalyst. The average recovery of precious metals from both wastes by arc furnace melting process was very high, which was up to in the range of 95～97%.

• Journal of IKEEE
• /
• v.21 no.4
• /
• pp.368-374
• /
• 2017

In this Paper, we developed a low power type LED security light using LED lighting that substitutes a 220[V] commercial power source for a solar cell module instead of a halogen or a sodium lamp. in addition, a PWM type drive control circuit is designed to minimize the heat generation problem and the drive current of the LED drive controller. in developed system, The light efficiency measurement value is 93.6[lm/W], and a high precision temperature sensor is used inside the controller to control the heat generation of the LED lamp. In order to eliminate the high heat generated from the LED lamp, it is designed to disperse quickly into the atmosphere through the metal insertion type heat sink. The heat control range of LED lighting was $50-55[^{\circ}C]$. The luminous flux and the lighting speed of the LED security lamp were 0.5[s], and the beam diffusion angle of the LED lamp was about $110[^{\circ}C]$ by the light distribution curve based on the height of 6[m].