• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.19 no.7
• /
• pp.481-492
• /
• 2018

The steel-plate concrete composite beam is composed of a steel plate, concrete and shear connector to combine two inhomogeneous materials. In general, the steel plate is assembled by welding an existing composite beam. In this study, the SPC beam was composed of folding steel plates and concrete, without a headed stud. The folding steel plate was assembled by a high strength bolt instead of welding. To improve the workability in a field construction, a hat-shaped cap was attached to the junction with a slab. Monotonic load testing under two points was conducted under displacement control mode to analyze the flexural strength of the SPC beam using a cap as the shear connector. Five specimens with shear connector types, protrusion length, and different thickness of steel plates were constructed and tested. The experimental results were analyzed through the relationship between the shear strength ratio and flexural strength in KBC 2009. The test results showed a shear strength ratio of more than 40 %. In the case of using a cap-like specimen as the shear connector, the flexural strength was 70% of the value calculated as a fully composite beam. In addition, the cap showed a smaller shear strength than the stud, but the cap served as a shear connection. When the thickness of the steel plate was taken as a variable, the steel plate exhibited a bending strength of approximately 70% compared to a fully formed steel plate, and exhibited similar deformation performance. Local buckling occurred due to incomplete composite behavior, but local buckling occurred at a 5% higher strength for a relatively thick steel plate. The buckling width also decreased by 15%.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.21 no.5
• /
• pp.47-53
• /
• 2020

The purpose of this study was to increase product reliability by improving the durability of the breech block for a 30mm Automatic Gun. The breech block is a key component of a gun that functions as chambering, closing, and extracting. The breech block requires high reliability, which needs to be improved because cracks of a breech block can occur early in operation. Cause analysis confirmed that the crack is caused by repeated impacts. Therefore, the following improvement measures were studied, and the effects were demonstrated using a firing test. The energy of impact absorption was increased by changing the material, and the stress concentration was mitigated by increasing the value of R. In addition, the fatigue life was increased by adding Shot-peening, deleting chromium plating, and changing the forging method. The firing test did not show firing trouble for up to 5,000 rounds. The start timing of the crack was delayed, and the depth was small. Therefore, the improved product was more durable than the existing product. This study can be used as a useful reference when assessing the improvement of the durability of similar products, life study, and criteria for crack acceptance.

• Journal of Korea Technology Innovation Society
• /
• v.19 no.4
• /
• pp.711-735
• /
• 2016

Drug Development is very important for promoting public health and pharmaceutical industry. There has been many studies on the efficiency of drug development, but there are few studies on the drug development R&D performed by government. Since CCR model assumes unidirectional influence of input and output, it is not appropriate to analyze the efficiency of R&D due to the time-lag and spill-over effect. Also, BBC model which assumes variable returns to scale has difficulty in deriving priorities between decision making units. Recently, Range Adjusted Measure (RAM) model has been suggested in R&D efficiency analysis. RAM model measures the efficincy by eliminating inefficiencies under variable returns to scale assumption, and its strong monotonicity enables to provide clear priorities between decision making units. In this study, we analyzed the efficiency of national R&D programs for drug development using the two-step approach, including RAM model and Tobit regression analysis, and discussed major policy implications.

• The Korean Society of Law and Medicine
• /
• v.16 no.1
• /
• pp.83-124
• /
• 2015

Currently, infertility and artificial insemination have increased. However, there is no detailed legislation about this. In this study, I'll consider the legal status of artificial insemination child. Through the examination of the overseas legislation, we may get the reference of the future legislation. If we consider the increasing of infertility, artificial insemination should be allowed. And due to the well-being of artificial insemination child, such as the United States and France, the artificial insemination child should be regarded the legal child of the infertile couples. When the contradiction between the subject's basic rights has occurred, we need to consider the welfare of the child preferentially. Because the artificial insemination child has no selection of opportunity in birth, unlike adults who select the artificial insemination in their own free will. The development of biotechnology should be for the treatment of human. But creation and improvement of human must be prohibited. In addition, the social investigation of recognition about A.R.T. and general public administrative legal regulation should be made. There is a need for balanced discipline through a multi-disciplinary research. This study may be providing a legal interpretation criteria of other biotechnology researches.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.19 no.6
• /
• pp.126-136
• /
• 2018

A steel-plate concrete composite beam is composed of a steel plate, concrete and shear connector to combine inhomogeneous two materials. The steel plate is assembled by welding an existing composite beam. In this study, new steel-plate concrete composite beam, called a SPC Beam, was developed to reduce the shear connector and improve the workability. The SPC Beam was composed of folding steel plates and concrete, without a shear connector. The folding steel plate was assembled using high strength bolt instead of welding. To improve the workability in field construction, a hat-shaped Cap was attached to the junction with a slab. Monotonic load testing under two points was conducted under displacement control mode. The flexural strength of the specimen for positive moment and negative moment was calculated using the plastic stress distribution method. The test results showed that the flexural strength of the new SPC Beam had 80% of the strength of a complete composite beam. In addition, increasing the composite ratio was possible through clearance controls of the cap. In this study, the performance of the SPC Beam was verified through additional experiments and analyses with the cross-sectional shape and cap as variables, because the representative shape in the positive negative moment region is targeted.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.21 no.10
• /
• pp.206-211
• /
• 2020

Tungsten alloys are used widely in general industrial fields, but they are difficult to cast, so products are manufactured using powder metallurgy. In this study, a mixed powder of tungsten, nickel, and iron homogenized using a ball mill was added to pure water as a solvent, and PVA as a binder was added to prepare a spray drying mixture. The mixed liquid was prepared using a spraying machine. A study was carried out to produce a granular powder that can reduce the variations between products during the molding and sintering process of the powder metallurgy method. A preliminary experiment was conducted to confirm the influence of the variables in the granulation process. Through the preliminary test results, this experiment was performed with the volume of solvent of the spray drying the mixture as an independent variable, and granular powder having a mean particle size similar to that of the existing mass-production conditions and an increased apparent density was prepared. In addition, a pilot test was conducted for the molding and sintering process. The improved granular powder reduced the characteristic variation (weight variation) of the mass-produced product.

• Proceedings of the Korea Technical Association of the Pulp and Paper Industry Conference
• /
• 2001.04a
• /
• pp.80-80
• /
• 2001

제지 공정의 효율적인 운영을 위한 수단으로 보류 및 탈수성의 분석은 매우 중요한 작 업 이 다. 보류 및 탈수 특성 을 평 가하기 위 하여 SR(Shopper-Riegler), CSF(Canadian S Standard Freeness tester) 그리고 원형 수초지기 등의 비난류 상태의 자연탈수 특성 평가 장치와 동적 조건의 감압식 탈수성 분석기 등이 사용되고 있다. 하지만 이것들은 제지 공정 에 보다 더 근접한 탈수 및 보류 특성을 평가하기에는 부족한 점이 있다. 특히 wet-end 첨 가제들의 효능을 보다 정확히 분석하는 것이 불가능하다. 이런 이유로 난류 발생과 감압 탈 수 둥을 유도한 탈수 특성 평가 장치 개발의 필요성이 커지고 있다. R RDA - HSF(Retention Drainage Analyzer- Handsheet Former)는 지료조성, 감압탈수 및 습지의 성형이 자동화되어 보류도와 탈수성, 종이지합 및 강도를 종합 평가 할 수 있는 새 로운 실험실용 초지기이다. 보다 현장에 가까운 초지 조건을 구현하기 위해서 지료의 농도 를 높이고 진공 탈수를 실시함에 따라 기존의 탈수성 분석기나 보류도 측정기의 단점을 보 완하게 되 었다. 본 연 구에 서 는 Canadian Standard Freeness test와 Dynamic Drainage Jar test 및 원 형 수초지기를 활용한 기존의 탈수성, 보류도 분석 결과와 RDA-HSF를 비교하여, 자연 탈수를 이용하는 기존의 탈수 및 보류 설비에 비해 현장 공정을 보다 현실적으로 재현할 수 있는 감압 탈수 초지 설비로서 RDA-HSF의 활용 가능성을 분석하였다. RDA-HSF를 활용한 실험실적 분석을 통해 현장의 상황올 유사하게 재현함에 따라 공정 운영 인자의 변화에 따른 제품의 품질 및 생산효율을 예측할 수 있게 된 바, 보다 효율적 인 공정 관리가 가능할 것으로 기대된다. 안료 입자의 경우 피인쇄체의 표면 공극을 채우고, 비히클의 경우 미세한 공극속으로 침투되어 경화됨으로써 피인쇄체가 지니고 있는 공극량을 감소시커 게 될 것이다. 그리고 피인쇄체의 각종 형태의 공극으로 침투된 잉크의 양에 반비례적으로 피인쇄체의 표변에 잉크가 잔류하게 될 것이다. 따라서 본 연구에서는 여러가지 안료를 사용하여 각각 다른 공극 특성을 지니는 도공지를 제조한 후 이들이 가지는 공극 특성과 잉크의 잔류 거동에 대해 고찰해 보고자 하였다.여 표면 유효층 일부만 오버레이시키며I 주조 및 단조가 불가능한 재료까지도 표면부에 오버레이 시킴으로 서 부품 및 설비의 제조에 있어 재료비의 절감과 제품의 수명이 획기적으로 개선될 수 있다. 그리고 최근에는 도금 빛 용사 둥과 같은 표면처리를 할 경우임의 소재 표면에 도금 및 용 사에 용이한 재료를 오버레이용접시킨 후 표면처리를 함으로써 보다 고품질의 표면층을 얻기위한 시도가 이루어지고 있다. 따라서 국내, 외의 오버레이 용접기술의 적용현황 및 대표적인 적용사례, 오버레이 용접기술 및 용접재료의 개발현황 둥을 중심으로 살펴봄으로서 아직 국내에서는 널리 알려지지 않은 본 기 술의 활용을 넓이고자 한다. within minimum time from beginning of the shutdown.및 12.36%, $101{\sim}200$일의 경우 12.78% 및 12.44%, 201일 이상의 경우 13.17% 및 11.30%로 201일 이상의 유기의 경우에만 대조구와 삭제 구간에 유의적인(p<0.05) 차이를 나타내었다.는 담수(淡水)에서 10%o의 해수(海水)로 이주된지 14일(日) 이후에 신장(腎臟)에서 수축된 것으로 나타났다. 30%o의 해수(海水)에 적응(適應)된 틸라피아의 평균 신사구체(腎絲球體)의 면적은 담수(淡水)에 적응된 개체의 면적보다 유의성있게 나타났다. 해수(海水)에 적응(適應

• Journal of the Korean Applied Science and Technology
• /
• v.37 no.3
• /
• pp.516-525
• /
• 2020

The densities of aqueous solutions of the amphiphile 2-(2-hexyloxyethoxy)ethanol (C₆E₂) were measured at 279.15 K and 282.15 K by vibrating-tube densitometry. Then using the density data of the binary C₆E₂ (1)/water(2) system, the excess volumes and partial molar volumes were determined at various compositions. Excess volume V^E exhibits negative deviation for the whole region of composition, which implies relatively stronger attraction between molecules. At the C₆E₂ mole fraction of around 0.45, V^E was at its minimum. Partial molar volume ${\bar{V}}_1$ increases monotonously with the mole fraction x₁(=x) and ${\bar{V}}_2$ decreases with x. Any particular point in ${\bar{V}}_1$ and ${\bar{V}}_2$, which may point to molecular association, was unobserved.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.16 no.11
• /
• pp.7754-7760
• /
• 2015

The outer tie rod is one of the part of steering system, the optimization process was executed to find the lightweight design. The inner tie rod was considered in the optimum design of an outer tie rod. it could be closer to the test condition than in the case of considering outer tie rod only. The aluminum forging material was considered as a weight reduction proposal. The target of optimization was the shape of the minimum weight to resist at the load of buckling. RSM and Kriging interpolation method were applied as a optimization method to consider the nonlinear shape optimization problem. Then, 16.3%, 16.6% of weight reduction was obtained from the result comparing with that of the initial model. The results of meta model optimization was compared with that of finite element method. The error values of buckling load estimation were 2.6%, 2.04%. and those of weight estimation were 0.17%, 0.13%. Therefore, it seemed that the result of Kriging model could be obtained closer to optimum value than that of RSM model.

• Proceedings of the Korea Water Resources Association Conference
• /
• 2019.05a
• /
• pp.258-258
• /
• 2019

계산 격자에 기반하여 천수 흐름을 모의할 때, 그 격자에 담긴 물의 양을 정확하게 파악할 필요가 있다. 예를 들어, 초기조건으로 수위가 부여된다면 계산격자의 기하 특성에 맞추어 흐름 변수인 수심이나 흐름 단면적으로 바꾸어야하기 때문이다. 필요에 따라서는 모의 결과를 수위로 보이거나 격자 속 수심을 계산에 사용할 수도 있으므로 그 역변환도 고려되어야 한다. 2차원의 삼각형 계산격자에 대해서는 물의 부피와 수위 관계(volume/free-surface relationship)가 이미 정확(exact)하게 구명되어 있다(Hwang, 2017, J. KWRA). 그런데 1차원 문제의 횡단면에서 흐름 단면적과 수위의 관계(area/free-surface relationship)는 수위로부터 면적 환산에 대해서는 정확하나 그 역변환은 그렇지 않다. 매 시간 단계에서 갱신된 흐름 단면적으로부터 수위를 환산하기 위해 미리 작성된 면적-수위 자료를 이용한 선형 보간이 적용된다(Goodell, 2011, The RAS Solution). 이때, 환산 정확도는 자료의 해상도에 의존된다. 다행히 하천 횡단면 대부분을 채워 흐르는 홍수모의에서는 이 문제가 그리 심각하지는 않다. 심지어 수위가 복단면 저수로 턱에 걸쳐있어 흐름단면적이 급변하는 경우에도 환산 수위의 정확도는 크게 훼손되지 않는다. 그러나 미미한 환산 오차일지라도 그로 인해 수위가 저수로 턱을 넘거나 그보다 작을 수 있다. 이 경우, 홍수터의 잠김여부에 따라 수면폭(top width)이 실제 계산 결과에 비해 크게 달라질 수밖에 없다. 수면폭 오차는 그것을 이용하여 결정되는 수리 수심(hydraulic depth)이나 평균 하상고(mean bed level)의 산정에도 전파된다. 이 연구에서는 하천 횡단면에서 수위와 흐름 단면적 사이의 환산 정확도를 크게 높일 수 있는 기법을 제시하였다. 먼저 하천 횡단면에서 주어진 수위에 대해 흐름 단면적을 산정할 수 있는 알고리듬을 보였다. 또한, 횡단면에서 수위와 흐름 단면적의 관계가 단조 증가 함수(monotonically increasing function)임에 착안하여 그 역변환에 대해 해 찾기(root finding) 방법의 하나인 Brent 기법을 적용하였다. 이 기법은 주어진 구간에서 도함수가 알려져 있지 않은 경우에 대해서도 효과적으로 해를 찾을 수 있는 것으로 알려져 있다(Press et al., 2002, Numerical Recipes in C, 2nd Ed.). 내성천 하류 수계의 333개 단면에서 수면폭에 대한 상대 오차를 살펴보면, 선형 보간에 의한 기존 방법으로는 면적-수위 자료의 수가 1,000개가 되어도 그 최대치가 1% 이내에 들지 않은 반면, 이 연구에서 제시한 기법으로 면적-수위 자료 없이도 1% 이내로 줄어드는 것을 확인하였다. 다만, 반복 계산에 의한 계산 시간의 증대를 피할 수 없다. 미리 작성된 면적-수위 자료를 이용하면 계산 비용을 줄일 수 있으며, 약 35개의 구간으로 나누었을 때 비용 대비오차가 적절하였다. 이 연구는 한국건설기술연구원(주요사업 과제번호: 20190116-001)의 지원에 의한 것이다.