• Korean Journal of Metals and Materials
• /
• v.50 no.8
• /
• pp.599-603
• /
• 2012

The microstructure of a hammer scale excavated from the Bogam-ri was examined in an effort to understand the iron technologies applied in the manufacturing of an iron forging process technology. The microstructures of oxide layer in the hammer scale were found to have crucial information about the ancient iron forging process treatment. The microstructure observed in the hammer scale can be distinguished by the forging process. First, the microstructure of the oxide layer in the hammer scale created by the forging process is Wstite (FeO) in the form of leaves. Latterly, the microstructure of the $W{\ddot{u}}stite$(FeO) in the hammer scale is observed to be in the form of a flat shape formed by a repeating forging process.

• Transactions of Materials Processing
• /
• v.28 no.3
• /
• pp.115-122
• /
• 2019

In this paper, finite element analysis of an automatic five-stage precision cold forging process of a yoke, a steering part of a passenger's car, is conducted with emphasis on spring back analysis at the yoke-forming stage and its experimental verification is subsequently made. An elastoplastic finite element method with MINI-element technique employed for the analysis of the entire process is explained. There is emphasis that the thin film of material formed between the punch and die in the stage may result to some errors especially in elastoplastic finite element analysis of spring back due to frequent remeshing. The numerical robustness of the spring back analysis in regards to remeshing is hence shown first through investigation into its effect on the predicted spring back. Experimental measurement of displacement due to spring back is carried out for comparison with the predicted results, and they are in a qualitative agreement with each other.

• Annual Conference of KIPS
• /
• 2013.05a
• /
• pp.438-441
• /
• 2013

자동차 관련 기술은 점차 전기, 전자 장치로 빠르게 바뀌어 가고 있다. 차량 내 연결되어 있는 전자 제어 장치들도 그에 따라 증가하게 되었고 장치간의 통신 성능도 중요하게 되었다. 가장 널리 사용되고 있는 차량용 네트워크 프로토콜로는 CAN(Controller Area Network)을 들 수 있다. 그러나 최근 통신 복잡도가 증가함에 따라 주기적 메시지 통신의 메시지 전송 지연 및 중단이 발생되고 있다. 본 논문에서는 이러한 문제에 대한 해결 방안을 제시하기 위해 메시지들의 스케줄 가능성 및 응답시간에 따른 실 시간성 검증 모델을 제안한다. CAN 메시지 수신 시 RMA(Rate Monotonic Algorithm)기반으로 메시지 스케줄 가능성 평가 모델을 개발하였다. 또한, CAN 메시지를 송신할 경우 RTA(Response Time Analysis)를 고려한 실 시간성 평가 모델을 제시하였다. 실험 1 에서는 기존 RMA 기법으로 통신을 수행한 결과 통신 중 중단되는 현상을 확인하였고 이후 제안 모델에서는 23%정도의 추가 시간을 확보하여 통신을 완료하는 것을 증명하였다. 실험 2 에서는 메시지 통신의 응답시간이 모두 제안된 Worst-case 응답시간 이내로 측정되어 실 시간성을 만족함을 확인하였다.

• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.21 no.3
• /
• pp.73-79
• /
• 2021

In the wave of the 4th industrial revolution, smart factory is required in many factories. However, small and mid-sized companies (SMEs) still have aging machines and are having difficulties in the data collection stage, which is the basis of smart factories. This study proposes a low cost monitoring method by using an open source based technology that extracts data from the image of the facility control panel without the need for modification of existing facilities. The proposed method was tested and evaluated for forging facilities in automobile parts manufacturing plants through prototyping. As a result of the evaluation, it was confirmed that low-cost facility monitoring is possible, and it will help SMEs build smart factories.

• Transactions of Materials Processing
• /
• v.33 no.5
• /
• pp.341-347
• /
• 2024

Many studies have focused on the optimal design of multi-stage forging molds. For optimal design progress, geometry parameters must be automatically modified, and the updated analysis file delivered. However, existing automation processes set and change parameters at the analysis input file stage, limiting them to simpler tasks like 2D shapes and basic process conditions (e.g., friction, elasticity), making it challenging to handle 3D asymmetric shapes. To address these limitations, an automated program was developed that modifies geometry directly in the CAD model, enabling the automation of complex 3D and asymmetrical shapes. In this process, a 3D mold is generated immediately after the drawing is input, automating the design of both the product and the mold without manual intervention. The program's effectiveness was demonstrated in the design and forging analysis of a multi-stage mold for M10 hex head bolts. This fully automated program reduced preprocessing time by approximately 6.7 times and successfully performed sensitivity analysis without manual input.

• Analytical Science and Technology
• /
• v.6 no.2
• /
• pp.167-180
• /
• 1993

The effects of coating variables on the formation of aluminide coating layer with good oxidation resistance on the strongest hot-forged superalloy in the world, KM 1557 developed at KIST by pack cementation process were studied. Pack aluminizing were performed by high-activity process with pure aluminium powders and by low-activity process with codep powders. For high-activity process, Al deposition rate, growth rate of coating layer, and cross-sectional microstructures were influenced by the species and additive amounts of activators and the additive amounts of pure aluminium powders. For low-activity process, Al deposition rate, growth rate of coating layer, and the cross-sectional microstructures were not influenced by the species but additive amounts of activators. Surface structures of coating layer were influenced by the species of activators. Regardless of aluminium activity, Al deposition rate was proportional to the square root of time and parabolic rate constants were different with the species of activators. The activation energy for deposition of aluminium was different with the species of activators for high-activity process. Regardless of the species of activators, the activation energy for deposition of aluminium was 12~14 Kcal/mole for low-activity process.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.25 no.9
• /
• pp.1438-1443
• /
• 2001

The significance of the casting/forging process for reducing the production cost of large components is being noted in these days. This casting/forging process is a method of forging a workpiece preformed by casting into the final shape. In this study, the casting/forging process has been applied in manufacturing a large aluminum flange in order to reduce press capacity and material cost. Firstly, a hot compression test was performed with cast cylindrical billets in order to determine the optimum forging condition of the aluminum flange. The optimum range of forging temperature of Al 5083 was from 420$\^{C}$ to 450$\^{C}$. The suitable strain rate was 1.5 sec(sup)-1. The deformation amount of a preform of a preform in a forging process is a key role in the mechanical properties of casting/forging products. In order to find the change of mechanical properties according to effective stain of cast aluminum billets, a hot upsetting test were performed with rectangular blocks and then a uniaxial tensile test was performed with specimens cut from the upsetted billets. The tensile strength and the elongation of cast/upsetted aluminum billets were increased largely until the effective strain was 0.7. FE analysis was performed to determine the configurations of case preform and die for an aluminum flange. In the FE analysis, the forging load-limit was fixed 1500ton for low equipment cost. The cast preform was designed so that the effective stain around the neck of a flange exceeded 0.7. From the result of FE analysis, optimal configurations of the cast preform and the die were designed for a large flange. The filling and solidification analysis for a sound cast-preform was carried out with MAGMA soft. In the forging experiment for an aluminum flange, it was confirmed that the optimal configuration of the cast preform predicted by FE analysis was very useful. The cast/forged products using designed preform were made perfectly without any defects.

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 1998.11a
• /
• pp.19-20
• /
• 1998

오버레이용접에 의한 표면개질기술(Weld Surfacing or Hardfacing Technology)은 내식성, 내 마모성, 또는 내열성을 갖는 합금의 용접재료를 모재 표면에 균일하게 용착(오버레이:Ovedayer)시킴으로써 목적하는 재료의 표면성질을 향상시키는 표면처리의 한 방법이으로써 1922년 Stoody가 Steel Tube에 Cr합금 분말을 충진한 용접봉을 제조하여 석유시추용 회전드릴의 선단 표면을 오버 레이 용접시켜 내마모성을 획기적으로 개선시킴으로써 이루어 졌다. 초기 오버레이 용접기술은 발전설비I 제철설비I 시벤트설비, 그리고 제지설비 등 주로 설비 부품들의 표면부 내마모성을 개선시키는 방향으로 주로 연구 개발이 이루어졌으나, 기술개발의 진전으로 탈황설비 둥의 표면부 내식성 향상, 연속주조롤 표면부의 내산화성, 내열피로성, 내마모 성 향상 둥을 위해 점차 산업전반에 널리 이용되고 있으며, 설비의 고도화 및 장수명화가 요구되 면서 본 기술의 중요성 또한 점차 부각되고 있다. 그림 1은 연강의 모재 위에 셀프쉴드플럭스코어드와이어(Self-Shield Flux Cored Wire:SS-FCW, 이하 55-FCW라 기술함)를 사용하여 오버레이 용접올 하는 장면을 도식적으로 나 타낸 것이다. 모재와 전극재인 용접봉(S5-FCW) 사이에서 아크가 발생되고, 아크열에 의해서 용접 봉 및 모재 일부가 용융되면서 모재 표면에 새로운 오버레이 표면층이 형성된다. 통상 오버레이 층의 1층 두께는 2-6mm 내외이며, 단층 혹은 다충 오버레이를 자유롭게 실시한다. 오버레이층의 물성은 아크열에 의한 모재로의 용입정도에 따라 1층부에서는 모재의 영향을 크게 받지만 오버레 이충 수가 증가된 3층부에서 부터는 전적으로 용접봉의 성분에 좌우된다. 사진 1은 연강(55-41)의 모재위에 크롬탄화물이 다량 함유된 고크롬 탄화물형 내마모재가 오버 레이된 내마모 복합강판 (wear plate)의 단면 미세조직 사진으로써 모재부와 오버레이충을 함께 보여주고 있다. 모재와 오버레이 충간의 경계면은 모재 일부가 용융된 후 웅고하면서 형성됨으로 인해서 도금이나 용사층과는 달리 매우 견고하게 결합되어 있다. 따라서 계면부의 탈락이라는 문 제점은 거의 없어 심한 응력을 받는 기계구조물 및 부품에도 본 기술은 널리 적용되고 있다. 그리고 사진 1에서 알 수 있는 바와 같이 모재와는 전혀 상이한 재료를 자유로이 선택하여 표면 유효층 일부만 오버레이시키며I 주조 및 단조가 불가능한 재료까지도 표면부에 오버레이 시킴으로 서 부품 및 설비의 제조에 있어 재료비의 절감과 제품의 수명이 획기적으로 개선될 수 있다. 그리고 최근에는 도금 빛 용사 둥과 같은 표면처리를 할 경우임의 소재 표면에 도금 및 용 사에 용이한 재료를 오버레이용접시킨 후 표면처리를 함으로써 보다 고품질의 표면층을 얻기위한 시도가 이루어지고 있다. 따라서 국내, 외의 오버레이 용접기술의 적용현황 및 대표적인 적용사례, 오버레이 용접기술 및 용접재료의 개발현황 둥을 중심으로 살펴봄으로서 아직 국내에서는 널리 알려지지 않은 본 기 술의 활용을 넓이고자 한다.

• Journal of KIISE:Databases
• /
• v.33 no.7
• /
• pp.682-692
• /
• 2006

Searching for gene products which have similar biological functions are crucial for bioinformatics. Modern day biological databases provide the functional description of gene products using Gene Ontology(GO). In this paper, we propose a technique for semantic similarity search for gene products using the GO annotation information. For this purpose, an information-theoretic measure for semantic similarity between gene products is defined. And an algorithm for semantic similarity search using this measure is proposed. We adapt Fagin's Threshold Algorithm to process the semantic similarity query as follows. First, we redefine the threshold for our measure. This is because our similarity function is not monotonic. Then cluster-skipping and the access ordering of the inverted index lists are proposed to reduce the number of disk accesses. Experiments with real GO and annotation data show that GORank is efficient and scalable.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.17 no.7
• /
• pp.518-528
• /
• 2016

It seems like many songs have the tonality of one key in jazz standards, but there are many cases in which more than one new key could be formed, despite being a short moment. Moreover, some songs contain keys of temporary changes many times in the event that keys are changed transitionally with the sequencing of cords many times, which is called 'Transitional Modulation with Sequences. The proceeding II-V-I of the major and minor keys are used as the sequencing of cords, and the most popular type in this sequencing pattern is the downward modulation in whole-steps or half-steps. The downward modulation in the interval of whole-steps is a useful technique; for example, there should be three compositions in the adjacency circumstances when it is used twice. We could express effectively a phenomenon that feelings go up to the climax and rapidly fall down. The downward modulation in half-steps must be more dramatic because a higher comparative aspect is made between the adjacent two keys.