• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.16 no.5
• /
• pp.467-474
• /
• 2004

This paper presents the results of an experimental investigation for the effect of radiant heat on the evaporation cooling of water droplet in the process of fire extinguishing. The experiments are mainly focused on the surface temperature, the surface roughness and the droplet diameter. The range of surface temperature is T$_{s}$ =80－14$0^{\circ}C$, surface roughness is R$_{a}$=0.08－0.64 ${\mu}{\textrm}{m}$ and the droplet diameter is $\Phi$=3.0 mm in the radiation. The results show that the evaporation time is shorter for the larger surface roughness and the volume of droplet increased when the surface roughness is 0.64 ${\mu}{\textrm}{m}$ at the surface temperature 127$^{\circ}C$. When the surface roughness is 0.64 ${\mu}{\textrm}{m}$, the heat flux is larger than the surface roughness is 0.08 ${\mu}{\textrm}{m}$ at the surface temperature 81$^{\circ}C$.>.>.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.25 no.1
• /
• pp.98-105
• /
• 2001

The fundamental and widely used spot welded sections of automobiles (hat and double hat-shaped section members) absorb most of the energy in a front-end collision. The sections were tested on axial static(10mm/min) and quasi-static(1000mm/min) loads. Based on these test results, specimens with various thickness, shape and spot weld pitch on the flange have been tested with impact velocity(7.19m/sec) the same as a real life car clash. Characteristics of collapse have been reviewed and a structure of optimal energy absorbing capacity is suggested.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2013.02a
• /
• pp.564-564
• /
• 2013

홀 추력기는 플라즈마를 이용하는 전기추력기 중 하나로, 인공위성의 자세제어, 궤도수정, 궤도천이 뿐만아니라 행성간 임무수행을 위한 우주선의 엔진으로 사용된다. 홀 추력기 채널 내부에 발생된 Xe 이온들은 양극과 음극 사이에 존재하는 전기장에 의해 가속되어 추력을 발생시킨다. 이때 Xe 이온들은 자기장에 의해 감금된 전자와 중성 Xe 원자 사이의 충돌에 의해 발생하며, 실험적 및 이론적 연구를 통해 단일 전하를 띤 이온(Xe II)뿐만 아니라 다중 전하(Xe III 등)를 띤 이온도 생성되는 것으로 알려져 있다. 이온의 전하량 비율은 홀 추력기의 추력효율 및 연료효율에 영향을 미치며, 다중 전하를 띤 이온의 높은 에너지는 채널벽의 침식문제를 야기하는 등 홀 추력기 이온빔의 전하량 분석 연구는 물리적 연구측면 뿐만아니라 실용적인 측면에서도 매우 중요하다. 본 연구에서는 자기장과 그에 수직한 방향의 전기장에서 발생하는 로렌츠 힘을 이용하여 이온의 전하량을 분석할 수 있는 $E{\times}B$ 탐침을 설계 및 개발하였다. 개발된 $E{\times}B$ 탐침은 70 mm 길이의 집속기와 $148{\times}138{\times}90mm$의 본체, 40 mm길이의 콜렉터로 구성된다. $E{\times}B$ 탐침 설계에 가장 중요한 균일한 자기장 설계를 위해 전산모사를 통해 최적화 작업을 진행하였으며, 실험을 위한 진단계의 최적화와 초기 실험결과가 발표될 예정이다.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2009.05a
• /
• pp.289-292
• /
• 2009

Injector dynamics of multi swirl injectors in an annular combustor have been investigated by LES(Large Eddy Simulation) turbulent model with MPI parallel computation technique. The present study employs the LM6000 lean premixed swirl-stabilized annular combustor. Real shape combustor is simulated in order to investigate the detail interaction mechanism among multi-injectors. The strong vortex breakdown occurs at the impinging surface between the adjacent injectors so that the complex and strong oscillatory pressure propagates inside of the combustor. Tangential pressure fluctuation mode was captured by including multi injectors in computational domain.

• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.18 no.1
• /
• pp.37-41
• /
• 2018

In this paper, we evaluate the power consumption of IEEE802.15.4e TSCH which uses the specific link scheduling scheme proposed in reference[1]. And we also compares it with the power consumption of conventional single channel IEEE802.15.4. The power consumption of IEEE802.15.4e TSCH is smaller than the conventional one under the any conditions of traffic. The reasons can be explained as the followings. Firstly, TSCH does not have backoff time because of using the collision free link scheduling. Secondly, there is the timing difference of MAC offset parameter between TSCH and conventional IEEE802.15.4 Lastly, the devices in TSCH mode sleep during the time slots which are not assigned to itself.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.39B no.12
• /
• pp.873-875
• /
• 2014

In this paper we describe an asynchronous MAC protocol with receiver-initiated duty cycling for energy-efficiency in wireless sensor networks(WSN). Legacy asynchronous MAC protocols, X-MAC and PW-MAC, has weaknesses which generates too many control packets and has data collision problem between multiple transmitters, respectively. Therefore, we propose a receiver-initiated asynchronous MAC protocol which generates control packets from transmitter to complement these disadvantages. Compared to the prior asynchronous duty cycling approaches of X-MAC and PW-MAC, the proposed protocol shows a improvement in energy-efficiency, throughput and latency from simulation results.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.20 no.10
• /
• pp.3262-3271
• /
• 1996

Flow patterns were measured in a shrouded centrifugal impeller. The flow rate in measurements was fixed at the value corresponding to a nearly zero incidence at the blade inlet. By using a single slanted hot-wire probe and a Kiel probe mounted on the impeller hub disk, the 3-D relative velocities and the rotary stagnation pressures were measured in seven circumferential planes from the inlet to the outlet of impeller rotating at 700 rpm, and the static pressure distribution along flow passage and the slip factor at impeller outlet were calculated from the measured values. From these measured data, the primary and secondary flows, the wake production and the static pressure rise in the impeller passage were investigated. Furthermore, the secondary flow patterns and the wake's location in this impeller passage were compared with those of the unshrouded impeller.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.49 no.1
• /
• pp.19-25
• /
• 2012

In evaluating the performance of RFID systems, the tag anti-collision arbitration has been considered to be an important issue. For BT(Binary Tree) and ABS( Adaptive Binary Splitting) protocols, the so-called capture effect, which presumably happens frequently in the process of readers' receiving messages from multiple tags, can lead to some failures in detecting all tags in BT and ABS. In this paper, we propose a new anti-collision protocol, namely FTB (Feedback TagID with Binary splitting), which can solve the aforementioned problem and improve the performance.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.25 no.7
• /
• pp.1131-1138
• /
• 2001

This paper concerns the crashworthiness of the widely used vehicle structure, the spot welded hat and double hat shaped section members, which are excellent on the point of the energy absorbing capacity and low production cost. The target of this paper is to analyze the energy absorption capacity of the structure against the front-end collision, and to obtain useful information for designing stage. Changing the spot weld pitches on the flanges, the hat and double hat shaped section members were tested on the axial collapse loads in impact velocities of 4.72m/sec, 6.54m/sec, 7.19m/sec and 7.27m/sec. To efficiently review the collapse characteristics of these sections, the simulation have been carried out using explicit FEM package, LS-DYNA3D. The solutions are compared with results from the impact collapse experiments.

• Journal of the Korean Society of Visualization
• /
• v.10 no.1
• /
• pp.21-26
• /
• 2012

Hydrophobic characteristics of high temperature metal surface were investigated by high-speed visualization of water droplet impact. An aluminum plate was used as the sample plate and the initial diameter of a water droplet was 2 mm. Transient behavior of a single droplet impinging on the surface with and without heating was captured by using a high speed camera running at 4,000 frames per second. The Leidenfrost phenomenon was demonstrated for the case of $300^{\circ}C$ surface temperature, however there was no rebounding of droplet on the cold plate due to hydrophilic nature. The experimental results show that the shape evolution of a droplet impinging on the surface varies with the Weber number, i.e. the ratio of impact inertia to capillary force. The overall water-repellent characteristics of the heated surface was very similar to that of the super hydrophobic surfaces.