• Clean Technology
• /
• v.11 no.1
• /
• pp.41-50
• /
• 2005

In this study, semibatch emulsion copolymerization of n-BA as adhesive component and MMA as coagulant component were carried out for the stable acrylic polymer latex in aqueous phase for polymer cement using LE-type nonionic surfactant as environmental friendly surfactant. The stable polymer emulsion was obtained with the increases of chain length(n) of this surfactant. The effect on the amount of LE-50 as nonionic surfactant were showed that the concentration of polymer latex were increased by increasing the amount of LE-50, whereas the average particle size were decreased by increasing the amount. The addition of functional monomer in initial reactor charge showed a significant effect on the final polymer concentration and the latex particle size. The single polymerization of each n-BA or MMA showed a very low concentration of polymer latex and very big particle size due to coagulation. In the polymerization composed of mixed monomer with MMA and n-BA, the larger the ratio of MMA to n-BA in the copolymers, the greater the amount of coagulum produced. It was found that a stable copolymers were obtained in the range of 15-35 % of n-BA. Moreover, incorporation of some functional monomers in addition to of main monomers became more stable polymer latex. Through DSC and IR analysis, the final polymer latex was composed by MMA/n-BA/AA/AM with a single Tg depending on the reaction conditions. As a result, the conditions of this acrylic polymerization could also be effectively controlled to get the desired final products.

• Analytical Science and Technology
• /
• v.18 no.2
• /
• pp.120-129
• /
• 2005

Volatile organic compounds (VOCs) have been recognized as major contributor to air pollution. The catalytic oxidationis is one of the most important processes for VOCs destruction due to the possibility getting high efficiency at low temperature. In this study, monometallic Pt, Ir and bimetallic Pt-Ir were supported to $TiO_2$. In order to distribute metals uniformly, $H_2O-H_2$ treatment method was used. Xylene, toluene and MEK were used as reactants. The monometallic or bimetallic catalysts were prepared by the excess wetness impregnation method and characterized by XRD, XPS, and TEM analysis. Pt catalyst showed higher conversion than Ir catalyst and Pt-Ir bimetallic catalyst showed the highest conversion. The catalysts prepared by $H_2O-H_2$ treatment had better VOC's conversion than that of nothing treatment. In the VOCs oxidation, Pt-Ir bimetallic catalysts had multipoint active sites, so it improved the range of Pt metal state. Therefore, bimetallic catalysts showed higher conversion of VOCs than monometallic ones. $H_2O-H_2$ treatment effected an uniform distribution of Pt particles. In VOCs oxidation was found to follow first order reaetion kinetics. The activation energy of $H_2O-H_2$ treatment catalysts was lower than that of untreated ones. In this study, the a small amount of Ir was used with Pt to promote the oxidation conversion of VOCs.

• Resources Recycling
• /
• v.29 no.3
• /
• pp.11-23
• /
• 2020

This study aims to investigate breakage and liberation characteristics of iron ore from Shinyemi mine, Jeongseon by ball mill. Parameters of breakage functions for three grade samples of iron ore were obtained using single-sized-feed breakage test and back-calculation based on nonlinear programming. The results showed that with the increase in the grade of iron ore, the breakage rate factor decrease whereas the particle size sensitivity decreases. This results from retardation of microcrack-propagation by magnetite grain in the ore. Breakage distribution analysis showed that the breakage mechanism appear to be impact fracture dominant with the increase of grade owing to the stress distribution effect by magnetite grain. Degree of liberation (DOL) increased with the increase in grade and decrease in particle size, respectively. Using the breakage function and size-DOL relationship, a model that can predict time-dependent-DOL is established. When scale-up factors from operating condition are available, the model is expected to be capable of predicting size and DOL with time in actual mining process.

• Journal of Digital Convergence
• /
• v.13 no.4
• /
• pp.417-423
• /
• 2015

Oil-in-water(o/w) nanoemulsions were prepared in the system of water/Span 80-Tween 80/long-chain paraffin oil via PIC method. With the increase of preparation temperature from 30 oC to 80 oC, the diameter of emulsion droplets decreased from 150 nm to 40 nm. By varying the HLB of mixed surfactants, we found that there was an optimum HLB around 13.0~14.0 corresponding to the minimum droplet size. The size of emulsion droplets increased upon increasing the ratio of oil/emulsifying agent. At $f{\leq}0.15$, the size of nanoemulsions could be kept constant more than 2 months. The increase in preparation temperature makes it possible for producing monodisperse nanoemulsions. Once the nanoemulsion is produced, the stability against Ostwald ripening is outstanding due to the extremely low solubility of the liquid paraffin oil in the continuous phase.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.26 no.2
• /
• pp.80-83
• /
• 2016

In the present paper, garnet structured $Y_3Al_5O_{12}:Ce^{3+}$ (YAG : Ce) ceramic phosphor plate (CPP) for high power laser diode (LD) was prepared and optical properties were analyzed. We synthesized monodispersed spherical nano-sized YAG : Ce particles by liquid phase method, fabricated phosphor ceramic plate with the addition of $Al_2O_3$. $75{\mu}m$ and $100{\mu}m$ thick YAG : Ce CPPs were compared in terms of the factors of conversion efficacy, thermal quenching, luminance and correlated color temperature (CCT). In conclusion, conversion efficacy decreased by 25 % in both samples and $100{\mu}m$ thick sample provides better optical properties of thermal quenching, maximum light conversion efficacy and maximum luminance value.

• Applied Chemistry for Engineering
• /
• v.23 no.2
• /
• pp.222-227
• /
• 2012

In this study, nano-emulsion containing ethyl acetate fraction of Polygonum aviculare (P. aviculare) extract was prepared and skin permeability of the nano-emulsion was evaluated. Nano-emulsion was prepared using homogenizer and microfluidizer by the high-energy method. The droplet size and loading efficiency of nano-emulsion containing ethyl acetate fraction of P. aviculare extract were determined. The mean droplet size was 238 nm and the loading efficiency was more than 98%. The size distribution of nano-emulsion was a monodispersed form and nano-emulsion was more stable than that of using typical emulsion without using the microfluidizer. The in vitro skin permeation study of nano-emulsion containing ethyl acetate fraction of P. aviculare extract was carried out using Franz diffusion cells. Compared to 1,3-butylene glycol, nano-emulsion showed greater values of cumulative permeation of ethyl acetate fraction from P. aviculare extract. These results indicate that the stability and skin permeability of nano-emulsion containing ethyl acetate fraction of P. aviculare exerting anti-oxidative and anti-aging activities were enhanced.

• Journal of the Society of Cosmetic Scientists of Korea
• /
• v.48 no.4
• /
• pp.343-355
• /
• 2022

Customized cosmetics are continuously mentioned as cosmetics in response to changes in the social environment and trends that emphasize individuality. Therefore, in this study, four types of nanoemulsion ampoules corresponding to skin types were prepared by different ratios of nanoemulsion formulation and ampoule formulation, and the applicability as a customized cosmetic base was checked. Particle size, polydispersity index, zeta potential, and viscosity according to time for 90 d were measured for four nanoemulsion ampoules with different volatile residues, and turbiscan was measured as a method for evaluating the stability of a colloidal dispersion system. Finally, human usability satisfaction was evaluated. As a result, it was confirmed that four kinds of nanoemulsion ampoules had a higher amount of volatile residue in the dry skin test product than in the oily skin test product. The pH was in the range of 6.41 to 6.88, and the particle size was in the range of 170 to 174 nm, and the change after 90 d was within 1.2% of the maximum, and there was no specificity in particle size stability. It was confirmed that the polydispersity index was almost constant, and showed a particle size distribution close to monodispersity by showing a change within a value smaller than 0.21 in all test products. The zeta potential was initially -63 mV or more for all four types of test products, and although it showed a slight decrease with time, there was little change to the extent of a maximum decrease of 2.5%. Viscosity was initially in the range of 4,100 to 5,100 cps and showed a decreasing trend with time, showing a maximum decrease of 37.7%. In the turbiscan measurement, the turbiscan stability index, a measure of stability, was all below 1.0, indicating dispersion stability. In the usability satisfaction evaluation (6 points) of 4 nanoemulsion ampoules corresponding to skin type, oily skin product (5.42 ± 0.67 points) > neutral oily skin product (5.36 ± 0.67 points) > neutral dry skin product (5.15 ± 0.69 point) > dry skin product (4.75 ± 0.75 points) in the order of evaluation. Four types of nanoemulsion ampoules are physically stable and have confirmed their applicability as a customized cosmetic base according to skin type, and are expected to expand in various ways.

• 한국신재생에너지학회:학술대회논문집
• /
• 2010.06a
• /
• pp.226.1-226.1
• /
• 2010

본연구에서는 GTL(gas to liquids)공정의 합성가스 생산을 위해 수증기-이산화탄소 복합개질반응(Combined Steam and Carbon dioxide Reforming of Methane, CSCRM)을 수행하였다. CSCRM은 수증기와 이산화탄소의 공급비 조절을 통해 $H_2$/CO비를 2로 맞추기 용이한 장점을 지니고 있어 다른 단일 개질 반응과 달리 합성가스 생산 시 $H_2$/CO 비율을 조절하기 위한 부가적인 공정이 필요하지 않아 경제적인 공정이다. 일반적으로 사용되는 Ni개질촉매는 가격대비 우수한 성능을 보이지만 S/C비가 낮은 CSCRM의 경우 촉매표면의 탄소침적에 의한 비활성화가 야기되는 문제점이 있다. 따라서 본 연구에서는 산소저장능력과 산소전달능력이 우수한 $CeO_2$를 조촉매로 첨가하여 표면에 형성된 코크 제거가 용이하도록 하였다. Ni-Ce/$MgAl_2O_4$촉매는 동시함침법(co-impregnation)으로 제조하였으며, Ni의 함량을 10wt%로 고정한 상태에서 Ce의 함량을 조절하여 Ce/Ni 최적비를 찾고자 하였다. XRD, TPR, BET, $H_2$-Chemisorption과 같은 촉매의 특성분석을 통해 촉매의 비표면적, 환원특성과 Ni입자의 분산도 등을 확인하였다. Ce를 첨가함에 따라 Ce2.5wt%까지는 비표면적이 증가하다가 이후 점차 줄어드는 경향성을 보였다. 또한, $H_2$-Chemisorption 결과 역시 비표면적과 유사한 경향성을 보였는데, Ce5.0wt%까지 Ni 분산도가 증가 하다가 다시 감소하는 것을 확인할 수 있었다. 반응실험은 $H_2O:CO_2:CH_4:N_2$ = 0.8:0.4:1:1의 공급조건에서 수행하였으며, 질소와 수소 환원분위기로 $700^{\circ}C$에서 1시간 환원 후 $650^{\circ}C$에서 $550^{\circ}C$범위로 온도를 떨어뜨려가면서 반응을 수행하였다. Ce를 첨가함에 따라 $CH_4$ 전환율이 증가를 하다가 Ce2.5wt% 이후 감소하는 것을 확인할 수 있었다. 이러한 높은 촉매 활성은 Ce 첨가로 인해 환원특성이 좋아지고 Ni분산도가 증가하여 담체와 강한 상호작용(SMSI)을 형성함으로 탄소침적 저항성 강화에 기인한 것이다.

• Journal of the Society of Cosmetic Scientists of Korea
• /
• v.38 no.1
• /
• pp.15-31
• /
• 2012

In our previous studies, the antioxidant, anti-aging, and antibacterial activities of Persicaria hydropipier L. extract, and the moisturizing effect of cream containing P. hydropipier extract were investigated. In this study, the cellular protective effects of P. hydropipier extract and isoquercitrin, main component from P. hydropipier in $^1O_2$-induced photohemolysis of human erythrocytes and ultraviolet B (UVB)-exposed HaCaT cells were investigated. Liposomes such as ethosome and elastic liposome for enhanced transdermal delivery were prepared. Size, loading efficiency, stability, and cumulative permeated amounts of ethosomes and elastic liposomes were evaluated. P. hydropipier extract and isoquercitrin showed more prominent cellular protective effect than (+)-${\alpha}$-tocopherol, known as lipid antioxidant at $5{\mu}g/mL$. P. hydropipier extract didn't show any characteristics of cytotoxicity at $50{\mu}g/mL$. When HaCaT cells were exposed to a single large dose ($400mJ/cm^2$) of UVB, the extract protected the cells against UVB radiation in a concentration dependent manner ($12.5{\sim}50{\mu}g/mL$). Cell viability of HaCaT cells exposed to UVB $400mJ/cm^2$ was increased by treatment with P. hydropipier extract or isoquercitrin from 36 % (cell viability of positve control groups) to 90 % (cell viability of P. hydropipier extract or isoquercitrin- treated groups). The size of 0.04 % P. hydropiper extract loaded ethosomes was 173.0 nm and the loading efficiency was 55.58 %. 0.04 % P. hydropiper extract loaded ethosomes were stable with as monodisperse particles for 1 week. The ethosome exhibited more skin permeability than general liposome and ethanol solution. The optimal ratio of lipid to surfactant ($Tego^{(R)}$ care 450) of 0.1 % P. hydropiper extract loaded elastic liposomes was observed to be 95 : 5. Vesicle size of 0.1 % P. hydropiper extract loaded elastic liposome was 176.5 nm. The deformability index of the elastic liposome was 16.4. The loading efficiency was 68.8 %. The elastic liposome containing P. hydropiper extract showed more skin permeability than liposome without surfactant ($Tego^{(R)}$ care 450).

• Journal of the Society of Cosmetic Scientists of Korea
• /
• v.43 no.1
• /
• pp.61-68
• /
• 2017

The key quality attributes of the pressed powder, one of base makeup products, are skin-affinity and spreadability. In general, there was a limit to meet skin-affinity and spreadability simultaneously, which are opposite attributes each other. In this study, air jet mill process was tried to satisfy two main properties. Skin-affinity was improved by a wet coating of sericite with a mixture of lauroyl lysine (LL) and sodium cocoyl glutamate (SCG). The application of mono-dispersed polymethyl methacrylate (PMMA) and diphenyl dimethicone/vinyl diphenyl dimethicone/silsesquioxane crosspolymer (DDVDDSC) improved both qualities. Air jet mill process has been mainly applied in the pharmaceutical and food industries, and is a method used for processing powder materials in cosmetic field. In this study, we were able to complete makeup cosmetics with an optimum particle size $6.8{\mu}m$ by combining the air jet mill process at the manufacturing stage. It was confirmed that the Ti element was uniformly distributed throughout the cosmetics by EDS mapping, and that the corners of the tabular grains were rounded by SEM analysis. It is considered that this can provide an effect of improving the spreadability when the cosmetic is applied to the skin by using a makeup tool. LL with excellent skin compatibility and SCG derived from coconut with little skin irritation were wet coated to further enhance the adhesion of sericite. SEM images were analyzed to evaluate effect of the dispersion and uniformity of PMMA on spreadability. With the spherical shapes of similar size, it was found that the spreading effect was further increased when the distribution was homogeneously mono-dispersed. The dispersion and spreadability of PMMA were confirmed by measuring the kinetic friction and optimal content was determined. The silicone rubber powder, DDVDDSC, was confirmed by evaluating the hardness, spreading value, and drop test. Finally, it was found that the dispersion of PMMA and silicone rubber powder affected spreadability. Such makeup cosmetics have excellent stability in drop test while having appropriate hardness, and good stability over time. Taken together, it is concluded that air jet mill process can be utilized as a method to improve skin-affinity and spreadability of the pressed powder.