• Journal of Korean Society of Steel Construction
• /
• v.29 no.2
• /
• pp.181-192
• /
• 2017

A beam splice method using inclined end-plates and high-strength tension bolts was developed. The end-plates welded to a bracket and a spliced beam are connected each other by using the tension bolts. In the present study, six exterior beam-to-column moment connections were tested under cyclic loading. Test parameters were the end-plate details and bolt arrangements. All specimens were designed so that moment resistances of the end-plates and bolts were greater than the required moment at the beam splice, in accordance with the design methods of AISC Design Guide 4. Test results showed that in the beam splices with the extended end-plates, the beam moment successfully transferred to the bracket, without any defeats such as excessive prying action of the end plates and brittle failure at the end plate-to-beam flange weld joints. However, the deformation capacities of the overall beam-to-column connections were limited due to the brittle failure of the beam-to-column flange weld joints. From the test results, recommendations for seismic design and detailing of the beam-to-column moment connection with inclined end-plate beam splice were given.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.10 no.4
• /
• pp.167-174
• /
• 2006

The purpose of this paper is to analyse and compare experimentally flexural behavior of RC beams strengthened with CFRP plates by different methods, which are divided into three classes: externally-bonded without end anchorage, externally-bonded with end anchorages, and anchored after prestressing of CFRP plates. Test results show that the RC beams strengthened with end anchorages have the improvement of ductility and flexural performance evaluation including ultimate strength and deflection, compared with only external bonding. Especially, RC beams with prestressed and anchored CFRP plates increase ultimate strength and ductility significantly.

• Journal of the Korean Society for Railway
• /
• v.16 no.3
• /
• pp.217-225
• /
• 2013

In this study, by considering the rail fastening support distance and the distance between the bridge and the abutment, the behavior of concrete track installed on a railway bridge end deck and the bridge end rotation were analyzed. In order to analyze the track-bridge interaction, bridge and abutment specimens with concrete track structures were designed and used in laboratory testing. At a constant fastening support distance, an increase in the bridge end rotation caused an increase in the displacement of the rail. Therefore, the displacement of the rail directly affects the rail and clip stress. Further, it is inferred that the results of multiple regression analysis obtained using measured data such as angle of bridge end rotation and fastening support distance can be used to predict the track-bridge interaction forces acting on concrete track installed on railway bridge deck ends.

• Journal of the Korea Concrete Institute
• /
• v.19 no.5
• /
• pp.603-611
• /
• 2007

Three interior slab-column connections designed by equal static moments and by different distribution of end and midspan moments were tested. Each test specimen consists of a 4.2 m square slab and a 355 mm square column stub. The slab thickness is 152 mm. Test results showed not only that flat plate systems can undergo considerable redistribution of moments from the uncracked state to final maximum capacity, but also that the distribution of moments is controlled largely by the distribution of reinforcement adopted by the designer. Tests also indicated that the punching shear strength of slabs can be affected by the redistributed moments.

• International Journal of Highway Engineering
• /
• v.12 no.4
• /
• pp.175-186
• /
• 2010

When a rigid post is exposed to traffic, it is hazardous not only to head-on impacts but also to side impacts. Clip-type slip base is an effective measure to reduce the severity of head-on impacts and side impacts as well because of its multi-directional release mechanism. Side impact tests were conducted and the results were analysed to demonstrate the hazardousness of a rigid post to a side impact and the crash worthiness of a post having clip-type slip base. For that, side impact test standard was made adapting the NCHRP Report 350, and 820kg-50km/h side impact tests were made for posts of D101.6mm(t=4.2mm) with and without slip base. Additionally, 35km/h side impact to the same post with slip base was conducted to check whether the clip-type slip base release mechanism works properly to the low impact speed. The tests revealed that the rigidly connected post was very hazardous to side impact while the post with the clip-type slip base reduced the impact severity tremendously.

• Magazine of the Korea Concrete Institute
• /
• v.10 no.3
• /
• pp.197-208
• /
• 1998

최근들어 손상된 실구조물의 보강공법들이 적용,발전되어왔다. 가장 보편적으로 사용된공법이 강판과 탄소섬유를 이용한 공법이지만, 이론적인 배경과 적용기술이 아직은 정립되어었지 않은 상태이다. 강판보강의 경우 단부에서의 응력집중이 보강 효과를 결정짓는 가장 중요한 변수이므로, 본 연구에서는 이러한 응력집중을 완화하기 위하여 단부에 보강판과확대판을 부착하여 실험을 하였고, 탄소섬유 보강 실험에서는 다층 시공시 보강량을 조절하여 실험하였다. 실험 결과는 하중-처짐, 항복하중, 최대하중, 보강재의 전단응력의 분포와 보강재의 파괴양상을 분류하여 정리하였다. 실험을 통하여 강판 보강의 경우 본 연구에서 제안된 단부에서의 보강방법이 보강효과가 향상된 것을 확인하였고 탄소섬유 보강시에는 탄소섬유의 보강량을 조절함으로써 경제적인 설계와 시공이 가능한 것으로 나타났다.

• Magazine of the Korea Concrete Institute
• /
• v.6 no.2
• /
• pp.138-147
• /
• 1994

The compressive strength of horizontal joints in precast concrete large panel structures depends on parameters such as grout and panel strength, detail of joint, joint moment, width of grout column, and etc. 44 specimens were tested to investigate the effects of parameters that influence the compressive strength of horizontal joints. The design formula specified in Korean Cock for compression horizontal joints must be reviewed, because it was based on the test results of the joint types not used in Korea. In this study comparing the test results, there fore, the validity of the design formulas was evaluated and a suitable formula was proposed to predict the ultimate strengths of compression horizontal joints. The increase of ultimate strengths was not observed, even if confined the horizontal displacement of slabs and reinforced the wall edge, when the grout strength is lower than panel strength. From the comparison of test results and those by the proposed formula, it was shown that proposed formula was suitable to predict the ultimate compressive strength of horizontal joints.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.10 no.6
• /
• pp.205-212
• /
• 2006

In recent investigations, reinforced concrete beams strengthened with Carbon Fiber Sheets (CFS) subjected to fatigue loading were reported to be failed at the ends of CFS by its debonding. U-shaped CFS were attached to both ends of the CFS when fatigue tests on strengthened beams were conducted to delay and/or prevent fatigue failures of adhesive interface. The experimental parameters of this study were the usage of anchorage at the ends of CFS, the number of CFS layers, and the applied load levels of 60%~90% of the static ultimate load obtained from the static tests. The failure modes and the load cycle-deflection relations were observed and discussed from the experimental results. Those results also showed that the U-shaped anchoring system changes the fatigue failure modes and influences greatly on the fatigue capacity of the strengthened beams.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.21 no.5
• /
• pp.74-82
• /
• 2017

Localized corrosions damages in their structural sections can be occurred affected by installed environment conditions with high temperature as near the coastline and humidity or their poor maintenance situation. In bearing supports of steel bridges, especially, lower web and vertical stiffener in end girder support can be easily corroded because of relatively higher humidity due to the narrow space in the end of girder and the wetted accumulated sediments affected by rain water or antifreezing admixture leaked from expansion joint. It can be related to change in their structural performance. In this study, thus, bearing strength test specimens were fabricated considering corrosion damage in the web and vertical stiffeners and the change in their bearing strengths were experimentally evaluated. From the test results, localized corrosion damage of structural members in the end girder affected the bearing strength of end girder support, especially, localized corrosion damage of the vertical stiffener relatively highly affected their bearing strengths.

• Journal of Korean Society of Steel Construction
• /
• v.22 no.6
• /
• pp.533-541
• /
• 2010

H-shaped beams, which are constructed between columns, are used widely as slaves in steel structures. The bending moments that occur on both ends of an H-shaped beam, however, are about twice the bending moment that occurs at the center of the H-shaped beam. Because such beam is designed with maximum bending moment, it is deeper and has smaller spaces. To improve these features, if both ends of an H-shaped beam that have maximum bending moments are merely reinforced, the beams could be designed by the bending moment at the center of the H-shaped beam. To analyze the structural performance of the proposed end-reinforced beams (eco-girders). Four specimens were prepared with the following parameters: end-reinforced steel plate, reinforced bars, and reinforced studs and experimental tests of the specimens were performed.