• 한국수자원학회:학술대회논문집
• /
• 한국수자원학회 2020년도 학술발표회
• /
• pp.239-239
• /
• 2020

상수관망은 수용가에게 용수를 공급하는 사회기반시설물로, 용수를 공급하는 과정에서 관내에 이물질, 스케일 등의 생성은 불가피하다. 관로 변경, 단수로 인한 비상시 용수 공급 등의 유향 및 유속이 변화가 발생할 경우 스케일이 박리되어 적수사고 등의 수질문제가 발생 할 수 있으며, 이에 사전에 스케일을 제거 할 필요성이 있다. 스케일을 제거하기 위해서는 주기적인 관세척이 필요하며, 대표적인 공법으로는 플러싱공법이 있다. 현재까지 플러싱공법에 대한 연구는 실험을 통한 적용 권장 기준으로 진행되어 왔으나, 실제 상수관망에서 적용권장 기준을 확보하기 위한 방안에 대한 연구는 미흡한 실정이다. 플러싱공법의 대표적은 종류는 재래식 플러싱공법과 단방향 플러싱공법이 있다. 재래식 플러싱공법은 제수밸브를 조작하지 않는 방법으로, 모든 소화전에서 용수를 방출하는 공법이다. 단방향 플러싱공법은 제수밸브를 조작하여, 일정한 방향으로 요수를 방출하는 공법이다. 단방향 플러싱공법은 재래식 플러싱공법보다 유속확보 측면에서 유리하여 관로 세척을 위한 유량 및 유속 확보가 용이하다. 단방향 플러싱공법을 적용하기 위해서는 관로의 유속을 확보하기 위해 세척구역 정의하는 것이 필요하다. 이에 본 연구에서는 세척구역 정의를 통한 플러싱공법 적용 방안을 제안하고자 한다. 세척구역은 크게 3단계로 구분한다. 먼저 블록단위의 세척순서를 결정하고, 블록 내 관망 세척구역을 결정한다. 이때 관로의 관경, 곡선구간, 세척구역의 길이를 고려하여 세척구역을 정의한다. 마지막으로 결정된 세척구역을 제수밸브의 위치, 조작 횟수에 근거하여 세척순서를 결정한다. 본 연구를 통해 실제 상수관망 플러싱공법 적용 절차 수립에 기여할 수 있다.

• 상하수도학회지
• /
• 제29권3호
• /
• pp.371-380
• /
• 2015

Particulate matters in a water distribution system are main causes of turbidity and discoloration of tap water. They could be removed by conventional or uni-directional flushing in a water distribution system. The behaviors and required flow velocity of particles are not well known for their flushing. A model water main and hydrant were made from transparent acrylic pipe of 30mm and 16mm in diameter, respectively. We analyzed the effect of flushing velocity, particle density, and particle diameter. We found that the existence of break-though velocities at which particles begin to be removed, and which are affected by their physical properties. The removal efficiencies seemed to be influenced by resuspension capabilities related to their upward movement from the bottom. Heavy particles like scale were hard to remove through upflow hydrant because the falling velocity, calculated using Stokes' law, was higher. Particle removal efficiencies of upward hydrant and downward drain showed minor differences. Additionally, the length between hydrant and control valve affected flushing efficiency because the particulate matters were trapped in this space by inertia and recirculating flow.

• 상하수도학회지
• /
• 제33권5호
• /
• pp.353-366
• /
• 2019

This research proposes an optimal flushing operation technique in an effort to prevent secondary water pollutions and accidents in aged pipes, and to improve the cleaning effect of unidirectional flushing. Water flow directions were analyzed using EPANET 2.0, while flushing and air scouring experiments in forward and reverse directions were performed in the field. In 42 experiments, average residual chlorine concentration and turbidity were improved after cleaning compared to before cleaning. It was found that even when the same cleaning method was used, further improvement of cleaning effect was possible by applying air injection and reverse direction cleaning techniques. By means of one-way ANOVA(Analysis of variance), it was also possible to statistically verify the need of actively utilizing air injection and reverse direction cleaning. Based on correlation between turbidity and TSS, the total amount of suspended solids removal was estimated for 874 flushing operations and 194 air scouring operations. The result showed that air scouring used more discharge water than flushing by an average of $4.9m^3$ yet with larger amounts of suspended solids removal by an average of 145.9 g. The result of analysis on turbidity values from 887 flushing operations showed low cleaning effect of unidirectional flushing for the pipes with diameters over 300 mm. In addition, the turbidity values measured during cleaning showed an increasing tendency as pipe age increased. The methodology and results of this research are expected to contribute to the efficient maintenance and improvement of water quality in water distribution networks. Follow-up research involving the measurement of water quality at regular time intervals during cleaning would allow a more accurate comparison of discharge water quality characteristics and cleaning effects between different cleaning methods. To this end, it is considered necessary to develop a standardized manual that can be used in the field and to provide relevant trainings.