• Polymer(Korea)
• /
• v.26 no.2
• /
• pp.160-167
• /
• 2002

We synthesized HPP-g-GMA copolymer using pre-irradiation method by E-beam and aminated HPP-g-GMA using amination reaction. Degree of grafting increased with increasing GMA monomer concentration and showed the maximum value of 130% at 1.46 M of GMA. The degree of amination increased with increasing the degree of grafting. When the degree of grafting was 100%, degree of amination showed the maximum value of 37.4%. The ion exchange capacity of aminated HPP-g-GMA was about 3.78 meq/g, and it showed remarkable adsorption ability of hollow fiber ion exchanger. Through the BET analysis, the surface area of aminated HPP-g-GMA was 54.83 $\m^2/g$ and the mean pore size was $26\AA$. These showed the decrease of surface area and the slight increase of the mean pore size. SEM results show that the thickness of fiber increased after the step of reaction and there pore blocking phenomena was not observed. The aminated HPP-g-GMA was synthesized successfully and found to be suitable for the adsorption and separation of anion.

• Applied Chemistry for Engineering
• /
• v.16 no.4
• /
• pp.502-506
• /
• 2005

In the presence of various clays, nylon/clay nanocomposites were synthesized by anionic polymerization of ${\varepsilon}$-caprolactam (CL) via monomer casting method. The effect of each clay on polymerization reaction was investigated and the change in gallery structure of clays during polymerization was analyzed by X-ray diffraction. When the three kinds of organo-clays were used in the amount of 2 wt% of CL, polymerizations were not successful due to an increase in viscosity during polymerization. Significant changes were not observed in the mechanical and thermal properties of the composites containing organo-clays with 1 wt%. On the other hand, composites containing natural clay up to 5 wt% were successfully prepared, and the composite with 5 wt% showed a decrease in tensile strength and elongation, and remarkable improvement in thermal properties.

• Polymer(Korea)
• /
• v.26 no.4
• /
• pp.415-421
• /
• 2002

A sulfonated PP-g-styrene ion-exchange hollow fiber membrane was prepared by pre-irradiation method with E-beam followed by sulfonation reaction. Degree of grafting increased with the increase of styrene monomer concentration and showed the maximum value of 128% at 80% of styrene monomer composition. Sulfonation yield increased with the degree of grafting. At 100% degree of grafting, sulfonation yield showed the maximum value of 13.4%. Ion exchange capacity of sulfonated HPP-g-styrene of 3.42 meq/g was attained, resulting in the remarkable increase of adsorption ability BET analysis proved that the surface area of sulfonated HPP-g-styrene was 62.54 $m^2/g$ and the mean pore size was 25 $\AA$. From the BSA adsorption experiments, the adsorption amount of BSA was increased with sulfonation. At 13.4% sulfonation yield the adsorption amount of BSA was maximum as 3.8 mg/g. Sulfonated HPP-g-styrene was synthesized successfully and suitable for the adsorption and separation of BSA.

• Polymer(Korea)
• /
• v.30 no.6
• /
• pp.550-555
• /
• 2006

The coating material for the ink-jet printing paper tends to be waterbase as the waterbase ink-jet ink is used more widely. Waterbase coating material consists of alumina sol as a pigment, poly(vinyl alcohol) as a main binder and polymeric additive for improving properties. In this study, polymeric auditive was synthesized by combining one or toto monomers among methacrylic acid, acrylic acid and acrylamide to the basic monomers, styrene and n-butylacrylate. The properties of printability such as ink absorption, ink spreading, and optical density, glossiness and water resistance were investigated by changing the kinds of surfactants, the composition of monomers and the structure of polymer particles. Results showed that materials containing anionic surfactant and/or acrylic acid had problems in com-patibility with alumina sol. Also, coating materials containing acrylamide had good printability and lout glossiness while those containing methacrylic acid did not have good printability and high glossiness.

• Polymer(Korea)
• /
• v.38 no.5
• /
• pp.682-686
• /
• 2014

To prepare transparent acrylic pressure sensitive adhesives (PSAs), terpolymer syrups were photopolymerized from 2- ethylhexyl acrylate and 2-hydroxyethyl acrylate with third monomer having different chemical structure. After polymerization, 1,6-hexanediol diacrylate as a crosslinker and a photoinitiator were added and then UV-irradiated to prepare the PSAs. The adhesion performances and optical characteristics of the PSAs were investigated. Their adhesion performance was dependent on the composition of monomers in the polymer chain but optical properties were maintained at a suitable level. The PSAs prepared by bulky and heteroatom-containing monomers such as IBOA, THFA, and ACMO showed better adhesion performance than others.

• Elastomers and Composites
• /
• v.47 no.3
• /
• pp.216-222
• /
• 2012

In this study, p-acryloyloxybenzoic acid(ABA) was synthesized with p-hydroxybenzoic acid(HBA) and acryloyl chloride(AC). The synthesized ABA monomer was grafted onto ethylene-propylene-diene rubber(EPDM) in toluene using benzoyl peroxide(BPO) as an initiator. The structures of ABA and EPDM-g-ABA were characterized by FT-IR, $^1H$-NMR, and $^{13}C$-NMR spectrometer. The graft ratio of EPDM-g-ABA increased with increasing the concentration of the initiator and the monomer. Mechanical properties such as tensile strength and compression set of the EPDM-g-ABA were improved with increasing the graft ratio. The $T_g$ and initial decomposition temperature were also increased with increasing the graft ratio.

• Polymer(Korea)
• /
• v.38 no.3
• /
• pp.293-298
• /
• 2014

We prepared hydrophilic porous supporters for the reinforced composite fuel cell membrane by radiation grafting of acrylonitrile (AN) and hydrophilic sodium allylsulfonate (SAS) into a porous polytetrafluoroethylene (PTFE) supporter. The physicochemical properties of the supporters prepared under various reaction conditions such as molar ratio of SAS/AN, monomer concentration, and irradiation dose were evaluated. FTIR was utilized to confirm the successful introduction of SAS/AN copolymer chains into the porous PTFE. The pores of the porous PTFE film were found to be decreased with an increase in the degree of grafting by using FE-SEM and gurley number. Furthermore, by analyzing the degree of grafting, contact angle, and TBO (toluidine blue O) uptake, the hydrophilicity of the prepared supporters was found to increase with an increase in the degree of grafting.

• Journal of the Korean Chemical Society
• /
• v.48 no.3
• /
• pp.229-235
• /
• 2004

For the study of hydrogen bonding phenomenon of high energetic compounds, we have been carried out a theoretical calculations for the nitromethane with the program Gaussian-98. The calculations at levels of restricted BLYP/6-311++G(d,p), B3LYP/6-311++G(d,p) and MP2/6-311++G have been performed to obtain molecular structures, hydrogen bonding effects and vibrational spectra of nitromethane monomer and dimer. The results show nitromethane is favored to make two hydrogen bonds between molecules and the nitromethane dimer is more stable than the monomer about 15.2, 19.4 and 32.6 kJ/mol for the BLYP, B3LYP, and MP2 level calculations, respectively.

• Polymer(Korea)
• /
• v.24 no.3
• /
• pp.287-298
• /
• 2000

In preparing micron-sized monodisperse polystyrene beads by dispersion polymerization, the conversion, and the particle size and its distribution were affected by the reaction temperature, concentration of the monomer, solvent and initiator, molecular weight and concentration of the steric stabilizer, amount of oxygen existing in the reactor, and an appropriate combination of these starting materials. Ethanol as a dispersing agent, styrene as a monomer, PVP as a steric stabilizer, AIBN as an initiator, DVB as a cross-linking agent and toluene as a co-solvent were the basic materials for the synthesis. The reaction rate and the conversion were increased with the reaction temperature and the amount of DVB from 1 to 4%, and the conversion was saturated after 10 hours of the reaction time. The optimum reaction recipe for the preparation of the monodisperse PS beads was 25% styrene monomer, 0.5% DVB, 25% toluene, 10-15% PVP, and 2 and 4% AIBN, thereby, 3.9~4 ${\mu}{\textrm}{m}$ and 3.4~9.3 ${\mu}{\textrm}{m}$ of polystyrene beads, respectively, were successfully synthesized.

• Polymer(Korea)
• /
• v.33 no.1
• /
• pp.33-38
• /
• 2009

Monodisperse polystyrene and its copolymer beads containing amine function were prepared for the electroless silver plating using reduction of silver alkylcarbamate complex in organic solvent. Soap-free emulsion polymerization was adopted for the polymerization of styrene, divinylbenzene (DVB), and 2-(N,N-dimethylamino) ethyl methacrylate (DAEMA) in the presence of poly (vinyl alcohol) in a water/methanol solvent. The resulting poly (styrene/DVB/DAEMA), containing 30/0$\sim$1.5/0$\sim$3 wt% in monomer composition, were found to be a sphere-type particle with diameter of 1 ${\mu}m$. Silver Ag-coated polystyrene beads were prepared by in sito reduction of a silver 2-ethylhexylcarbamate (Ag-EHCB) complex solution with hydrazine without pretreatment of polystyrene beads. Robust Ag/polystyrene beads were analyzed by SEM, UV -visible spectrometer and XRD.