• Transactions of the Korean Society of Automotive Engineers
• /
• v.11 no.4
• /
• pp.52-57
• /
• 2003

Common rail injection system is flexible in injection timing, injection duration and pressure in engine. Many researches have reported on the merits in the application of common rail systems. This research investigated on characteristics and performance for single cylinder diesel engine with a common .ail injection system by varying major parameters such as injection timing, injection duration and common rail pressure. The injection timing and injection duration were controlled by electronic pulse generated. and common rail pressure were controlled by PCV driver. The 498cc single cylinder diesel engine was used in this experiment. All data for combustion pressure, injection timing and injection duration were recorded by Labview. Furthermore, this test was focused on how to optimize injection conditions.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.16 no.1
• /
• pp.181-187
• /
• 2008

Recently, alternative fuels are drawing more attentions due to the increasing need for lower emission characteristics and fuel consumption rate in automotive engines. The GTL(gas to luquid) is the one of most favored candidates. It has higher cetane number(more than 75) and almost negligible sulphur and aromatic contents. Therefore, enhanced emission characteristics are expected even in the application in diesel engines without any modification. In this study, the cylinder pressure and heat release, emission characteristics with fuel injection timings are compared between diesel and GTL fuel in the single cylinder diesel engine. Noticeable reduction in PM, THC and CO emission are observed due to lower sulphur and aromatic contents in GTL. Also, the ignition delay decreased due to higher cetane number of GTL, which slightly decreased the amount of NOx emissions. With the retards of main injection timing, NOx decreases more for the case of GTL, while the level of THC and CO emissions still remains lower than the case of diesel. Therefore, there is much room for the control of injection timing for NOx reduction without sacrificing THC and CO emissions. With the retards of main injection timing, Small size distribution of PM became lager and there amount increased. But from all conditions, size distribution of PM for the case GTL was lower than Diesel.

• Journal of Advanced Marine Engineering and Technology
• /
• v.39 no.9
• /
• pp.911-917
• /
• 2015

The objective of this work focuses on the analysis of injection rate and macroscopic spray behavior characteristics with injection pressures as well as combustion and exhaust emission characteristics with injection timing and injection pressure by using a common rail single-cylinder diesel engine. The injection rate was measured by applying the Bosch method, and macroscopic spray behavior characteristics were analyzed with a constant-volume vessel and a high-speed camera. In addition, combustion and emission characteristics were analyzed in a common-rail single-cylinder diesel engine with precise control of fuel injection timing and pressure. For injection pressures of 30MPa and 50MPa, the injection rate was higher at 50 MPa, and the spray development (penetration) was also higher in the same elapsed time. The peak in-cylinder pressure and rate of heat release showed a tendency to decline as injection timing was delayed, and the peak in-cylinder pressure and rate of heat release were slightly higher for higher injection pressures. Higher injection pressures also reduced the mean effective pressure, while the indicated mean effective pressure and torque increased as injection timing was delayed to TDC. Nitrogen oxides had a peak level at injection timings of $BTDC20^{\circ}$(30MPa) and $BTDC15^{\circ}$(50MPa); carbon monoxide emissions were reduced by delaying injection timing from $BTDC30^{\circ}$.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.21 no.7
• /
• pp.692-698
• /
• 2020

This paper examines the effects of a multi-stage pilot split injection strategy on combustion and exhaust emission factors in a single-cylinder diesel engine. One analysis noted that in the single-injection condition, the maximum in-cylinder pressure and rate of heat release were highest. The pilot injection quantity was evenly divided, showing a tendency to decrease as the number of injections increased. In another injection condition, when the multi-stage pilot split injection strategy was applied, IMEP, engine torque, and combustion increased. The COV_IMEP was greatest with the lowest combustion efficiency. The combustion ability was poor. In a single injection condition, the O₂ concentration in the exhaust gas was the lowest and the CO₂ was the highest. When the multi-stage split injection strategy was applied, the low temperature combustion process proceeded, and the oxidation rate of CO₂ decreased while the emission level increased. In a single injection condition in which a locally rich mixture was formed, the HC emission level showed the highest results. A 55.6% reduction of NOx emission occurred under a three-stage pilot injection condition while conducting a multi-stage pilot split injection strategy.

• 한국연소학회:학술대회논문집
• /
• 2015.12a
• /
• pp.41-44
• /
• 2015

Experimental study was conducted to investigate the effect of ultra-high injection pressure on combustion and emission characteristics in a single-cylinder diesel engine. Electronically controlled ultra-high pressure fuel injection system consistently supplied the fuel of ultra-high pressure up to 250 MPa. Various injection pressures, 40 to 250 MPa, were applied and compared. A injector with eight identical nozzle holes which have diameter of $105{\mu}m$ was used. The results showed high potential to improve the nitrogen oxide (NOx) and particulate matter (PM) trade-off relationship with an ultra-high injection pressure and the exhaust gas recirculation (EGR).

• Transactions of the Korean Society of Automotive Engineers
• /
• v.24 no.2
• /
• pp.152-160
• /
• 2016

The market demand for diesel engine tends to increase in general passenger cars as well as commercial vehicles because of its advantages. However, to meet the vehicle emissions regulation which will be more stringent in the future, it is necessary to plurally apply all after-treatment technologies such as diesel oxidation catalyst (DOC), catalyzed diesel particulate filter (CDPF), lean NOx trap (LNT) and selective catalytic reduction (SCR), and so on. Accordingly, the exhaust after-treatment system for diesel vehicle requires the technology of minimizing the numbers of catalysts by integrating every individual catalysts. The purposes of this study is to develop hybrid exhaust after-treatment device system which simultaneously uses LNT/DPF and SCR/DPF catalyst concurrently reducing NOx and particulate matter (PM). As the results, the hybrid system with $NH_3$ generated at LNT/DPF working as a reducing agent of SCR/DPF catalyst, improving NOx conversion rate, was found to be more excellent in de-NOx performance than that in LNT/DPF alone system.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.14 no.3
• /
• pp.95-102
• /
• 2006

Recently particulate matter(PM) emission regulations are becoming more strict for diesel engines. There is increasing interest for measuring not only concentration but also size of the particles. Laser-induced incandescence (LII) has emerged as a promising technique for measuring particle volume fraction and size. In this study, the Simple Time Resolved-LII method was applied to exhaust of Ethylene diffusion flame and diesel engine exhaust for measuring soot and PM size. The particle size data from LII technique were calibrated using Field Emission Scanning Electron Microscope(FE-SEM) and Transmission Electron Microscope(TEM) photographs. In diesel engine experiments for particle size measurement, results from LII measurement are in a good agreement with those from TEM photograph, and difference between two measurements was less than 16%.

• Journal of ILASS-Korea
• /
• v.19 no.4
• /
• pp.204-210
• /
• 2014

Experimental study was conducted to investigate the effect of EGR(exhaust gas recirculation) on engine noise using single cylinder combustion ignition engine. Under constant engine rotary speed of 1200 RPM, 8 mg fuel quantity was injected with 15, 18 and 21% of oxygen ratio and 1400 bar of injection pressure. Using the in-cylinder pressure data acquired by a piezoelectric transducer, the engine performance parameters were calculated. Radiated engine noise measured for 10 seconds was analyzed using spectral characteristics and sound quality metrics such as loudness, sharpness, roughness. From the obtained engine performance parameters and sound quality metrics, effect of oxygen ratio of the premixed air, start of injection timing on frequency characteristic and sound quality metrics were analyzed. Correlation analysis was conducted between MPRR(maximum pressure rise rate), RI(ringing intensity) and sound quality metrics. RI was identified as the most important factor having influence on the sound quality metrics.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.35 no.12
• /
• pp.1375-1381
• /
• 2011

Combustion processes in an optically-accessible single-cylinder heavy-duty diesel engine equipped with a highpressure common-rail injection system were investigated for JP-8 and diesel. Direct imaging and two-color thermometry were employed to verify the emission trend for both fuels. The combustion process was characterized by image analysis with focus on luminosity. The results of two-color thermometry were analyzed on the basis of the flame temperature and KL factor distribution. Analysis of the combustion process by direct imaging showed that the ignition delay was longer for JP-8 than for diesel, while the flame was extinguished rapidly. Analysis of the flame luminosity showed that the combustion intensity was higher for diesel and that the flame lasted for a longer duration in this case. Two-color thermometry results showed that the high-temperature region extended over a large area during JP-8 combustion, implying the formation of a large amount of $NO_x$. In addition, the KL factor showed low level over a large area and relatively homogeneous in the case of JP-8 combustion, which implied that less smoke was produced when using this fuel.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.19 no.2
• /
• pp.20-25
• /
• 2011

The purpose of this work is an experimental investigation of combustion and emission characteristics in DI diesel engine applied high EGR rate as a method of low-temperature combustion. In order to analyze the effect of EGR rate variation, a single-cylinder DI diesel engine was operated under various EGR rate conditions. In addition, injection timing was variously controlled to investigate the effect of injection timing in DI diesel engine using the cooled-EGR system. The NOx emissions were decreased in accordance with the increase of EGR rate. On the contrary, soot emissions were generally increased under applied EGR conditions. However, soot emissions were decreased in a few injection timings under high EGR rate conditions. The EGR results show that the ignition delay were increased by decreased oxygen concentrations in combustion chamber under the high EGR rate.