• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.23 no.7
• /
• pp.807-815
• /
• 2019

In this paper, we design a power amplifier to support quad-band in wireless communication devices using RF CMOS 180-nm process. The proposed power amplifier consists of low-band 0.9, 1.8, and 2.4 GHz and high-band 5 GHz. We proposed a structure that can support each input matching network without using a switch. For maximum linear output power, the output matching network was designed for impedance conversion to the power matching point. The fabricated quad-band power amplifier was verified using modulation signals. The long-term evolution(LTE) 10 MHz modulated signal was used for 0.9 and 1.8 GHz, and the measured output power is 23.55 and 24.23 dBm, respectively. The LTE 20 MHz modulated signal was used for 1.8 GHz, and the measured output power is 22.24 dBm. The wireless local area network(WLAN) 802.11n modulated signal was used for 2.4 GHz and 5.0 GHz. We obtain maximum linear output power of 20.58 dBm at 2.4 GHz and 17.7 dBm at 5.0 GHz.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.44 no.1
• /
• pp.79-84
• /
• 2007

In this paper, a fully-integrated low phase noise multi-band CMOS VCO using automatic level controller (ALC) and switched LC tank has been presented. The proposed VCO has been fabricated in a 0.13-um CMOS process. The switched LC tank has been designed with a pair of capacitors and two pairs of inductors switched using MOS switch. By using this structure, four band (2.986 ${\sim}$ 3.161, 3.488 ${\sim}$ 3.763, 4.736 ${\sim}$ 5.093, and 5.35 ${\sim}$ 5.887 GHz) operation is achieved in a single VCO. The VCO with 1.2 V power supply has phase noise of -118.105 dBc/Hz @ 1 MHz at 2.986 GHz and -113.777 dBc/Hz @ 1 MHz at 5.887 GHz, respectively. The reduced phase noise has been approximately -1 ${\sim}$ -3 dBc/Hz @ 1 MHz in the broadest tuning range, 2.986 ${\sim}$ 5.887 GHz. The VCO has consumed 4.2 ${\sim}$ 5.4 mW in the entire frequency band.

• Journal of KIISE:Information Networking
• /
• v.29 no.2
• /
• pp.117-128
• /
• 2002

Virtual LAN (VLAN) is an architecture to enable communication between end stations as if they were on the same LAN regardless of their physical locations. VLAN defines a limited broadcast domain to reduce the bandwidth waste. The Newbridge Inc. developed a layer 3 VLAN product called VIVID, which configures a VLAN based on W subnet addresses. In a VIVID system, a single route server is deployed for address resolution, VLAN configuration, and data broadcasting to a VLAN. If the size of the network, over which the VLANS supported by the VIVID system spans, becomes larger, this single route server could become a bottleneck point of the system performance. One possible approach to cope with this problem is to deploy multiple route servers. We propose two architectures, organic and independent, to expand the original VIVID system to deploy multiple route servers. A course of simulations are done to analyze the performance of each architecture that we propose. The simulation results show that the performances of the proposed architectures depend on the lengths of VLAN broadcasting sessions and the number of broadcast data frames generated by a session. It has also been shown that there are tradeoffs between the scalability of the architecture and their efficiency in data transmissions.