• Korean Journal of Agricultural and Forest Meteorology
• /
• v.23 no.1
• /
• pp.15-33
• /
• 2021

In this study, the possibility of discriminating Fire blight (FB) infection tested using the hyperspectral imagery. The reflectance of healthy and infected leaves and branches was acquired with 5 nm of full width at high maximum (FWHM) and then it was standardized to 10 nm, 25 nm, 50 nm, and 80 nm of FWHM. The standardized samples were divided into training and test sets at ratios of 7:3, 5:5 and 3:7 to find the optimal bands of FWHM by the decision tree analysis. Classification accuracy was evaluated using overall accuracy (OA) and kappa coefficient (KC). The hyperspectral reflectance of infected leaves and branches was significantly lower than those of healthy green, red-edge (RE) and near infrared (NIR) regions. The bands selected for the first node were generally 750 and 800 nm; these were used to identify the infection of leaves and branches, respectively. The accuracy of the classifier was higher in the 7:3 ratio. Four bands with 50 nm of FWHM (450, 650, 750, and 950 nm) might be reasonable because the difference in the recalculated accuracy between 8 bands with 10 nm of FWHM (440, 580, 640, 660, 680, 710, 730, and 740 nm) and 4 bands was only 1.8% for OA and 4.1% for KC, respectively. Finally, adding two bands (550 nm and 800 nm with 25 nm of FWHM) in four bands with 50 nm of FWHM have been proposed to improve the usability of multispectral image sensors with performing various roles in agriculture as well as detecting FB with other combinations of spectral bands.

• Korean Journal of Remote Sensing
• /
• v.36 no.2_1
• /
• pp.155-165
• /
• 2020

In this present study, the sensitivity of O₄ Air Mass Factor (AMF) to Aerosol Peak Height (APH) has been investigated using radiative transfer model according to various parameters(wavelength (340 nm and 477 nm), aerosol type (smoke, dust, sulfate), aerosol optical depth (AOD), surface reflectance, solar zenith angle, and viewing zenith angle). In general, it was found that O₄ AMF at 477 nm is more sensitive to APH than that at 340 nm and is stably retrieved with low spectral fitting error in Differential Optical Absorption Spectroscopy (DOAS) analysis. In high AOD condition, sensitivity of O₄ AMF on APH tends to increase. O₄ AMF at 340 nm decreased with increasing solar zenith angle. This dependency isthought to be induced by the decrease in length of the light path where O₄ absorption occurs due to the shielding effect caused by Rayleigh and Mie scattering at high solar zenith angles above 40°. At 477 nm, as the solar zenith angle increased, multiple scattering caused by Rayleigh and Mie scattering partly leads to the increase of O₄ AMF in nonlinear function. Based on synthetic radiance, APHs have been retrieved using O₄ AMF. Additionally, the effect of AOD uncertainty on APH retrieval error has been investigated. Among three aerosol types, APH retrieval for sulfate type is found to have the largest APH retrieval error due to uncertainty of AOD. In the case of dust aerosol, it was found that the influence of AOD uncertainty is negligible. It indicates that aerosol types affect APH retrieval error since absorption scattering characteristics of each aerosol type are various.

• Geophysics and Geophysical Exploration
• /
• v.26 no.1
• /
• pp.18-30
• /
• 2023

Submarine mud volcanos are topographic features that resemble volcanoes, and are formed due to eruptions of fluidized or gasified sediment material. They have gained attention as a source of subsurface heat, sediment, or hydrocarbons supplied to the surface. In the continental slope of the Canadian Beaufort Sea, mud volcano exists at various water depths. The MV420, is an active mud volcano erupting at a water depth of 420 meters, and it has been the subject of extensive study. The Korea Polar Research Institute(KOPRI) collected high-resolution seismic data and heat flow data around the caldera of the mud volcano. By analyzing the multi-channel seismic data, we confirmed the reverse-polarity reflector assumed by a gas hydrate-related bottom simulating reflector(BSR). To further elucidate the relationship between the BSR and gas hydrates, as well as the thermal structure of the mud volcano, a numerical geothermal model was developed based on the steady-state heat equation. Using this model, we estimated the base of the gas hydrate stability zone and found that the BSR depth estimated by multi-channel seismic data and the bottom of the gas hydrate stability zone were in good agreement., This suggests the presence of gas hydrates, and it was determined that the depth of the gas hydrate was likely up to 50 m, depending on the distance from the mud conduit. Thus, this depth estimate slightly differs from previous studies.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.43 no.5 s.347
• /
• pp.35-44
• /
• 2006

Reflective semiconductor optical amplifiers(R-SOAs) were designed with high gain, wide optical bandwidth, high thermal reliability and wide modulation bandwidth in TO-can package for the transmitter of wavelength division multiplexed-passive optical network(WDM-PON) application. Double trench structure and current block layer were introduced in designing the active layer of R-SOA to enable high speed modulation. The injection power requirement and the viable temperature range of WDM-PON system are experimentally analysed in based on Amplified Spontaneous Emission(ASE)-injected R-SOAs. The effect of the different injection spectrum in the gain-saturated R-SOA was experimentally characterized based on the measurements of excessive intensity noise, Q factor, and BER. The proposed spectral pre-composition method reduces the bandwidth of injection source below the AWG bandwidth and thereby avoids spectrum distortion impeding the intensity noise reduction originated from the amplitude squeezing.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2013.02a
• /
• pp.416-417
• /
• 2013

최근 질화물계 발광다이오드(light emitting diode, LED) 소자는 핸드폰, 스마트 TV 등의 디스플레이 분야와 실내외조명, 감성조명, 특수조명 등의 조명분야에 그 응용분야가 급속히 확대되고 있다. 이러한 LED 소자는 에너지 절감과 친환경에 장점을 가지고, 가까운 미래에 조명시장을 대체할 것으로 예상된다. 이를 만족하기 위해서는 현재보다 더 높은 효율을 갖는 LED 개발이 요구되어지고 있는 상황이다. 일반적으로 질화물계 LED 소자의 효율은 내부양자 효율, 광추출 효율 등으로 나타낼 수 있다. 내부 양자효율은 성장된 결정의 질의 개선 및 다층의 이종접합 또는 다중양자우물 구조와 같이 활성층의 캐리어 농도를 높이는 접합구조로 설계되어 80% 이상의 효율을 나타낸다. 그러나 광추출 효율은 이에 미치지 못하고 있다. 이는 반도체 재료의 높은 굴절률로 인하여 빛이 외부로 탈출하지 못하고 내부로 반사되거나 물질 안에서 흡수가 일어나기 때문이다. 따라서 이러한 문제를 해결하기 위해 많은 연구 그룹들은, 표면에 패턴 형성하여 빛의 전반사를 줄여 그 효율을 올리는 연구결과를 보고하고 있다. 대표적인 방법으로는 wet etching, 전자빔 리소그라피, 나노임프린트 리소그라피, 레이저 홀로 리그라피, 나노스피어 리소그라피 등이 사용되고 있다. 이 중, 나노스피어 리소그라피는 폴리스틸렌 혹은 실리카 등과 같은 나노 크기의 bead를 사용하여 반도체 기판 표면에 단일층으로 고르게 코팅한 마스크로 사용하여 패턴을 주는 방법이다. 이 방법의 장점으로는 대면적에 균일한 패턴을 형성할 수 있고, 공정비용이 저렴하여 양산하기에 적합하다는 특징이 있다. 나노스피어 리소그라피를 통해서 표면에 생성된 패턴 모양의 각도에 따라서, 식각되는 깊이에 변화에 따라 실험한 결과들은 있지만, 아직까지 크기가 다른 나노입자들의 마스크 이용하여 형성된 패턴 밀도에 따른 광 추출 효과에 대한 연구가 많이 미흡하다. 따라서 본 연구에서는 다양한 크기의 실리카로 패턴을 형성시켜 패턴 밀도에 대한 광추출 효율의 효과에 대해서 조사하였다. 실험 방법으론, DI, 에탄올, TEOS, 암모니아의 순서대로 그 혼합 비율을 조정하여 100, 250, 500 nm 크기의 나노입자를 합성하였고 이것을 질화물계 LED의 표면 위에 단일층으로 스핀코팅 방법을 통해 코팅을 하였다. 그 후 ICP-RIE 방법으로 필라 패턴을 형성하였는데, 그 결과 100 nm SiO2 입자를 이용한 경우 $4.5{\times}10^9$/$cm^2$, 250 nm의 경우 $1.4{\times}10^9$/$cm^2$, 500 nm의 경우 $0.4{\times}10^9$/$cm^2$의 패턴의 밀도를 보여주었다(Fig. 1). 패턴의 밀도에 따라 전계광학적 특성을 확인하여 보았는데, 그 결과는 평평한 표면과 비교하였을 때 100 nm에서 383%, 250 nm에서는 320%, 500 nm에서는 244% 상승하는 결과를 보여주었다(Fig. 2). 이번 실험을 통해서 LED의 광추출 효율은 표면 모양과 깊이 뿐 아니라 밀도가 커질수록 그 효율이 올라간다는 사실을 알 수 있었다.

• Journal of the Korean Vacuum Society
• /
• v.20 no.4
• /
• pp.288-293
• /
• 2011

We investigated the effects of piezoelectric field on the electro-absorption characteristics in InGaN/GaN multiple-quantum well (MQW) green light emitting diodes (LED). Double crystal X-ray diffraction measurement was performed to study the crystalline property and indium (In) composition in the MQW active layer. To measure the electro-luminescence and electro-reflectance (ER) spectroscopy, we fabricated the $1{\times}1\;mm^2$ large-area green LED chip. The piezoelectric field inside the LED structure was evaluated from the Vcomp in active layer by the ER spectra. Finally, we analyzed the electro-absorption characteristics of the green LED by using the photo-current spectroscopy.

• The Journal of the Acoustical Society of Korea
• /
• v.34 no.6
• /
• pp.411-422
• /
• 2015

This paper presents an overview of the geological environment investigation and underwater acoustic measurements for the purpose of "Study on the Relationship between the Geological Environment and Acoustic Propagation in Shallow Water", which are jointly carried out by KIOST (Korea Institute of Ocean Science & Technology) and Hanyang University in the western shallow water off the Taean peninsula in the Yellow Sea in April-May 2013. The experimental site was made up of various sediment types and bedforms due to the strong tidal currents and coastal geomorphological characteristics. The geological characteristics of the study area were intensively investigated using multi-beam echo sounder, sub-bottom profiler, sparker system and grab sampler. Acoustic measurements with a wide range of research topics in a frequency range of 20~16,000 Hz: 1) low frequency sound propagation, 2) mid-frequency bottom loss, 3) spatial coherence analysis of ambient noise, and 4) mid- frequency bottom backscattering were performed using low- and mid-frequency sound sources and vertical line array. This paper summarizes the topics that motivated the experiment, methodologies of the acoustic measurements, and acoustic data analysis based on the measured geological characteristics, and describes summary results of the geological, meteorological, and oceanographic conditions found during the experiments.

• The Journal of Korean Academy of Prosthodontics
• /
• v.54 no.4
• /
• pp.379-386
• /
• 2016

Purpose: The present study aims at researching the subjective satisfaction of patients who have experienced both conventional impression taking and digital impression taking to measure the possibility of wide clinical application of digital impression. Materials and methods: The study surveyed 170 adult patients over the age of 20, between October 2015 and April 2016, who voluntarily consented to participation and who experienced both conventional impression and digital impression at five dental hospitals that use intraoral digital impression. A total of 128 surveys were used for data analysis, involving frequency analysis, multiple response frequency analysis, descriptive statistics, and contingency table analysis, with the significance level set at 0.05. Results: Responses on the reason for taking impressions using the digital method appeared in the order of 'for implant treatment' (43.8%), 'for crown treatment' (30.5%), and 'for inlay treatment' (15.6%). Patients satisfaction was higher for digital impression taking than conventional impression taking (P<.05). As the preferred choice of impression, digital impression (60.2%) was higher than conventional impression (11.7%). Responses on the reason for choosing digital impression taking appeared in the order of 'no vomiting reflex' (35.1%), 'reliability of 3D digital scanning' (33.8%), and 'short time' (33.8%). Conclusion: The patients preferred digital impression taking to conventional impression taking in terms of satisfaction.

• Korean Journal of Optics and Photonics
• /
• v.17 no.1
• /
• pp.47-53
• /
• 2006

The Integrated Ballistics Identification Systems (IBIS) is widely used for bullet and casing signature identification. The IBIS obtains a pair of ballistic signatures from two bullets (or casings) using optical microscopy, and estimates a correlation score which can represent the degree of signature match. However, this method largely depends on lighting and surface conditions because optical image contrast is primarily a function of test surface's slope, shadowing, multiple reflections, optical properties, and illumination direction. Moreover, it can be affected with surface height variation. To overcome these problems and improve the identification system, we used well known surface topographic techniques, such as confocal microscopy and white-light scanning interferometry. The measuring instruments were calibrated by a NIST step height standard and verified by a NIST sinusoidal profile roughness standard and a commercial roughness standard. We also suggest a new analysis method for the ballistic identification. In this method, the maximum cross-correlation function CCFmax is used to quantify the degree of signature match. If the compared signatures were exactly the same, CCFmax would be $100\%$.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.22 no.8
• /
• pp.745-753
• /
• 2011

In this paper, the planar monopole antenna for multi-band service is proposed. The proposed antenna, which is a rectangular patch antenna with a U-shaped slit based on a monopole antenna for wide bandwidth characteristic, is designed and analyzed. The antenna size has been miniaturized by using the U-shaped slit. The frequency characteristics are modified and optimized by varying specific parameters. To obtain desired frequency bands, the U-shaped slit and patch lines have been applied. Whole antenna dimensions including the ground plane are $35{\times}50{\times}1\;mm^3$, and the antenna part size is $35{\times}27\;mm^2$. It is fabricated on the FR-4 substrate(${\epsilon}_r=4.4$) using a microstrip line of $50{\Omega}$ for impedance matching. For the measured results, the impedance bandwidth below a VSWR of 2 is 790~916 MHz, 1.74~2.14 GHz, and 2.36~3.13 GHz. The fabricated antenna is satisfied with the aimed impedance bandwidth in GSM/DCS/US-PCS/UMTS/Bluetooth/S-DMB applications.