• Korean Journal of Optics and Photonics
• /
• v.14 no.2
• /
• pp.142-145
• /
• 2003

The nonreciprocal phase shift characteristics of infinite slab optical waveguides with magneto-optic materials in the cladding layer was calculated at 1.55 ${\mu}{\textrm}{m}$ for optical isolators. The infinite slab waveguide structures considered in this paper were as follows. rho magneto-optic materials used as a cladding layer were Ce:YIG and LNB(LuNdBi)$_3$(FeAl)$_{5}$)$_{12}$,). Their specific Faraday rotations Θ$_{F}$ are 4500$^{\circ}$/cm, 500$^{\circ}$/cm at wavelength 1.55 ${\mu}{\textrm}{m}$ respectively. The guiding layer with multi-quantum well structure was used, and it consists of 1.3Q and InGaAs. In order to investigate the effect of evanescent field penetrating the cadding, layer, guiding mode characteristics were calculated for the cases when the substrate is InP and air. We calculated the minimum lengths of 90$^{\circ}$ nonreciprocal phase shifters and their optimum guiding layer thicknesses in various optical waveguide structures.res.s.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.28 no.2
• /
• pp.105-112
• /
• 2017

In order to satisfy the diffusion of multimedia service in mobile communication and the demand for high-speed communication, it is essential to modify and improve high efficiency, wideband and nonlinear characteristic of multiband power amplifier. This research is designed to implement a single-stub matching circuit as a 2nd harmonic one that meets conditions of the Class-J power amplifier. Low characteristic impedance of the single-stub line is necessary to suit conditions of wideband Class-J. This research uses ceramic substrates having high permittivity to implement the single-stub line with low characteristic impedance, which eventually results in an amplifier satisfying the output impedance terms of Class-J in wideband frequency range. This result attributes to use of GaN HEMT packaged with a 2nd harmonic matching circuit and external fundamental circuit. The measurement results of the Class-J amplifier confirms the following characteristics: more than output power of 50 W(47 dBm) in bandwidth of 1.8~2.7 GHz(0.9GHz), maximum drain efficiency of 72.6 %, and maximum PAE characteristic of 66.5 %.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2010.02a
• /
• pp.315-315
• /
• 2010

결정질 실리콘을 포함하는 태양전지의 광전효율은 표면에 입사되는 태양광의 반사를 제외하면 흡수된 광자에 의해 생성되는 전자-정공쌍의 상대적인 비율인 내부양자효율에 의존하게 된다. 실제 생성된 전자-정공쌍은 기판재료의 결정상태와 전기광학적 물성 등에 의해 일부가 재결합되어 2차적인 광자의 생성이나 열로서 작용하고 최종적으로 전자와 정공이 완전히 분리되고 전극에 포집되어 실질적인 유효전류로 작용한다. 16% 이상의 고효율 결정질 실리콘 태양전지양산이 요구되고 있는 현실에서 광전효율 개선 위해 가장 우선적으로 고려되어야 할 변수는 입력 태양광스펙트럼에 대한 결정질 실리콘 표면반사율을 최소화하여 광흡수를 극대화하는 것이라 할 수 있다. 이의 해결을 위하여 대기와 실리콘표면 사이의 굴절률차이가 크면 클수록 태양광스펙트럼에 대한 결정질 실리콘의 광반사는 증가하기 때문에 상대적으로 낮은 굴절률의 $SiO_x$나 $SiN_x$와 같은 반사방지막을 광입력 실리콘표면에 증착하여 광반사율 저감공정을 적용하고 있다. 이와 더불어 결정질 실리콘표면을 화학적으로 혹은 플라즈마이온으로 50-100nm 직경의 바늘형 피라미드형상으로 texturing 함으로 광자들의 다중반사 등에 기인하는 광흡수율의 증가를 기대할 수 있기 때문에 태양전지효율 개선에 긍정적인 영향을 미치는 것으로 이해된다. 본 실험에서도 고효율 다결정 실리콘 태양전지 양산공정에 적용 가능한 ICP-RIE기반 결정질 실리콘표면에 대한 texturing 공정기술을 연구하였다. Double Langmuir 플라즈마 진단시스템(DLP2000)을 적용하여 사용한 $SF_6$와 $O_2$ 개스유량과 챔버압력, 플라즈마 파워에 따른 이온밀도, 전자온도, 포화이온전류밀도, 플라즈마포텐셜의 공간분포를 모니터링하였고 texturing이 완료된 시료에 대하여 A1.5G 표준태양광스펙트럼의 300-1100nm 파장대역에서 반사율을 측정하여 그 변화를 관찰하였다. 본 연구에서 얻어진 결과를 간략히 정리하면 Si texturing에 가장 적합한 플라즈마파워는 100W, $SF_6/O_2$ 혼합비는 18:22, 챔버압력은 30mtorr 등이고 이에 상응하는 플라즈마의 이온밀도는 $2{\sim}3{\times}10^8\;ions/cm^3$, 전자온도는 14~15eV, 포화전류밀도는 $0.014{\sim}0.015mA/cm^2$, 플라즈마포텐셜은 38~39V 범위 등이었다. 현재까지 얻어진 최소 평균반사율은 14.2% 였으며 최적의 texturing패턴 플라즈마공정 조건은 이온에 의한 Si표면원자들의 스퍼터링과 화학반응에 의한 증착이 교차하는 플라즈마 에너지 및 밀도 상태인 것으로 해석된다.

• Korean Journal of Optics and Photonics
• /
• v.29 no.1
• /
• pp.19-27
• /
• 2018

A change in object distance would generally change the magnification of an optical system. In this paper, we have proposed and designed a double-Gauss optical system with a fixed magnification and image surface regardless of any change in object distance, according to moving the lens groups a little bit to the front and rear of the stop, independently parallel to the direction of the optical axis. By maintaining a constant size of image formation in spite of various object-distance changes in a projection system such as a head-up display (HUD) or head-mounted display (HMD), we can prevent the field of view from changing while focusing in an HUD or HMD. Also, to check precisely the state of the wiring that connects semiconductor chips and IC circuit boards, we can keep the magnification of the optical system constant, even when the object distance changes due to vertical movement along the optical axis of a testing device. Additionally, if we use this double-Gauss optical system as a vision system in the testing process of lots of electronic boards in a manufacturing system, since we can systematically eliminate additional image processing for visual enhancement of image quality, we can dramatically reduce the testing time for a fast test process. Also, the Gaussian bracket method was used to find the moving distance of each group, to achieve the desired specifications and fix magnification and image surface simultaneously. After the initial design, the optimization of the optical system was performed using the Synopsys optical design software.

• Korean Journal of Optics and Photonics
• /
• v.33 no.1
• /
• pp.28-34
• /
• 2022

We study through computational simulation the focal performance of an infrared (IR) Fresnel lens, composed of a multilayer-graphene zone plate formed under a graphene electrode. Here the Fermi level E_F of the patterned multilayer graphene is adjusted by the overlying graphene electrode. The Fresnel lens effect, with respect to the reflectance contrast between the graphene electrode and the 8-layer graphene zone plate placed on a glass substrate, has been analyzed over a broad wavelength range from 4 to 30 ㎛. As the optimal wavelength of 8 ㎛ (considering the reflectance and the reflectance-contrast ratio) is incident upon the Fresnel lens with a focal length of 240 ㎛, the focal intensity is enhanced by a factor of 4.3 as the E_F of multilayer graphene increases from 0.4 eV to 1.6 eV, and is improved by a factor of 5.8 as the number of graphene layers increases from two to eight. As a result, an all-graphene-based IR Fresnel zone-plate lens, exhibiting multifocal function (240 ㎛ and 360 ㎛) according to the selected E_F, is proposed as an ultrathin lens platform.

• Journal of Advanced Navigation Technology
• /
• v.25 no.6
• /
• pp.536-542
• /
• 2021

In this paper, we proposed a triple band printed monopole antenna with a bent branch strips for WiFi / 5G. An antenna structure in which bent strips for generating multiple resonance are attached in the form of branches was newly proposed based on a typical monopole strip vertically erected as a triple band antenna structure. The proposed antenna is designed on a FR-4 substrate with dielectric constant 4.3, thickness of 1.6 mm, and size of 28×40 mm². The measured impedance bandwidth is 430 MHz (2.22~2.65 GHz) in the 2.4 GHz WLAN, 450 MHz (3.38~3.83 GHz) in the 3.5 GHz and 2390 MHz (4.95~7.34 GHz), In particular, it has been observed that antenna has a stable omnidirectional radiation patterns as well as gain of 1.537 dBi, 1.878 dBi and 2.337 dBi in the entire frequency band of interest.

• Journal of Sensor Science and Technology
• /
• v.7 no.3
• /
• pp.154-162
• /
• 1998

A planar Bi-Sb multijunction thermal converter with high thermal sensitivity and small ac-dc transfer error has been fabricated by preparing the bifilar thin film Pt-heater and the hot junctions of thin film Bi-Sb thermopile on the $Si_{3}N_{4}/SiO_{2}/Si_{3}N_{4}$-diaphragm, which functions as a thermal isolation layer, and the cold junctions on the dielectric membrane supported with the Si-substrate, which acts as a heat sink, and its ac-dc transfer characteristics were investigated with the fast reversed dc method. The respective thermal sensitivities of the converter with single bifilar heater were about 10.1 mV/mW and 14.8 mV/mW in the air and vacuum, and those of the converter with dual bifilar heater were about 5.1 mV/mW and 7.6 mV/mW, and about 5.3 mV/mW and 7.8 mV/mW in the air and vacuum for the inputs of inside and outside heaters, indicating that the thermal sensitivities in the vacuum, where there is rarely thermal loss caused by gas, are higher than those in the air. The ac-dc voltage and current transfer difference ranges of the converter with single bifilar heater were about ${\pm}1.80\;ppm$ and ${\pm}0.58\;ppm$, and those of the converter with dual bifilar heater were about ${\pm}0.63\;ppm$ and ${\pm}0.25\;ppm$, and about ${\pm}0.53\;ppm$ and ${\pm}0.27\;ppm$, respectively, for the inputs of inside and outside heaters, in the frequency range below 10 kHz and in the air.

• Journal of the Korean Vacuum Society
• /
• v.19 no.3
• /
• pp.211-216
• /
• 2010

The luminescence properties of $In_{0.5}Ga_{0.5}As/In_{0.5}Al_{0.5}As$ multiple quantum wells (MQWs) grown on $In_{0.5}Al_{0.5}As$ buffer layers have been studied by using photoluminescence (PL) and time-resolved PL measurements. A$1-{\mu}m$ thick $In_{0.5}Al_{0.5}As$ buffer layers were deposited on a 500 nm thick GaAs layer, followed by the deposition of the InGaAs/InAlAs MQWs. In order to investigate the effects of InAlAs buffer layer on the optical properties of the MQWs, four different temperature sequences are used for the growth of InAlAs buffer layer. The growth temperature for InAlAs buffer layer was varied from 320^{\circ}C to $580^{\circ}C$. The MQWs consist of three $In_{0.5}Ga_{0.5}$As wells with different well thicknesses (2.5 nm, 4.0 nm, and 6.0 nm thick) and 10 nm thick $In_{0.5}Al_{0.5}$As barriers. The PL spectra from the MQWs with InAlAs layer grown at lower temperature range ($320-580^{\circ}C$) showed strong peaks from 4 nm QW and 6 nm QW. However, for the MQWs with InAlAs buffer grown at higher temperature range ($320-480^{\circ}C$), the PL spectra only showed a strong peak from 6 nm QW. The strongest PL intensity was obtained from the MQWs with InAlAs layer grown at the fixed temperature of $480^{\circ}C$, while the MQWs with buffer layer grown at higher temperature from $530^{\circ}C$ to $580^{\circ}C$ showed the weakest PL intensity. From the emission wavelength dependence of PL decay times, the fast and slow decay times may be related to the recombination of carriers in the 4 nm QW and 6 nm QW, respectively. These results indicated that the growth temperatures of InAlAs layer affect the structural and optical properties of the MQWs.

• Journal of the Korean Vacuum Society
• /
• v.20 no.6
• /
• pp.449-455
• /
• 2011

The luminescence properties of $In_{0.5}Ga_{0.5}As/In_{0.5}Al_{0.5}As$ multiple quantum wells (MQWs) grown on $In_{0.4}Al_{0.6}As$ buffer layer have been investigated by using photoluminescence (PL) and time-resolved PL measurements. A 1-${\mu}m$-thick $In_{0.4}Al_{0.6}As$ buffer layers were deposited at various temperatures from $320^{\circ}C$ to $580^{\circ}C$ on a 500-nm-thick GaAs layer, and then 1-${\mu}m$-thick $In_{0.5}Al_{0.5}As$ layers were deposited at $480^{\circ}C$, followed by the deposition of the InGaAs/InAlAs MQWs. In order to study the effects of $In_{0.4}Al_{0.6}As$ layer on the optical properties of the MQWs, four different temperature sequences are used for the growth of $In_{0.4}Al_{0.6}As$ buffer layer. The MQWs consist of three $In_{0.5}Al_{0.5}As$ wells with different well thicknesses (2.5-nm, 4.0-nm, and 6.0-nm-thick) and 10-nm-thick $In_{0.5}Al_{0.5}As$ barriers. The PL peaks from 4-nm QW and 6-nm QW were observed. However, for the MQWs on the $In_{0.4}Al_{0.6}As$ layer grown by using the largest growth temperature variation (320-$580^{\circ}C$), the PL spectrum only showed a PL peak from 6-nm QW. The carrier decay times in the 4-nm QW and 6-nm QW were measured from the emission wavelength dependence of PL decay. These results indicated that the growth temperatures of $In_{0.4}Al_{0.6}As$ layer affect the optical properties of the MQWs.

• Korean Journal of Materials Research
• /
• v.9 no.3
• /
• pp.274-281
• /
• 1999

Usually sputtering and electroless plating methods were used for manufacturing metal-alloy thin film magnetic memory devices. Since electroless plating method has many merits in mass production and product variety com­pared to sputtering method, many researches about electroless plating have been performed in the United State of America and Japan. However, electroless plating method has not been studied frequently in Korea. In these respects the purpose of this research is manufacturing Co-Mn-P alloy thin film on the corning glass 2948 by electroless plating method using sodium hypophosphite as a reductant, and analyzing deposition rate, alloy composition, microstructure, and magnetic characteristics at various pH's and temperatures. For Co-P alloy thin film, the reductive deposition reaction 0$\alpha$urred only in basic condition, not in acidic condition. The deposition rate increased as the pH and temperature increased, and the optimum condition was found at the pH of 10 and the temperature of $80^{\circ}C$. Also magnetic charac­teristics was found to be most excellent at the pH of 9 and the temperature of $70^{\circ}C$, resulting in the coercive force of 8700e and the squareness of 0.78. At this condition, the contents of P was 2.54% and the thickness of the film was $0.216\mu\textrm{m}$. For crystal orientation, we could not observe fcc for $\beta$-Co. On the other hand,(1010), (0002), (1011) orientation of hcp for a-Co was observed. We could confirm the formation of longitudinal magnetization from dominant (1010) and (1011) orientation of Co-P alloy. For Co-Mn-P alloy deposition, coercive force was about 1000e more than that of Co P alloy, but squareness had no difference. For crystal orientation, (l01O) and (lOll) orientation of $\alpha$-Co was dominant as same as that of Co- P alloy. Likewise we could confirm the formation of longitudinal magnetization.