• Applied Chemistry for Engineering
• /
• v.27 no.5
• /
• pp.521-526
• /
• 2016

Some thiadiazole and dithiocarbamate derivatives were desinged and synthesized in order to study the potential use as anti- wear additives. Their anti-wear properties in three different base oils (DB-51, soybean, and 100 N) were evaluated using a four-ball wear tester (ASTM D4172). The solubilities of dithiocarbamate derivatives in the base oils were better than those of thiadiazole derivatives. The compounds containing oleoyl group rather than nonanoyl group gave good anti-wear properties. The solubilities and anti-wear properties were explained by the polarity of the compounds.

• Proceedings of the Korean Vacuum Society Conference
• /
• 1999.07a
• /
• pp.194-194
• /
• 1999

다이아몬드 박막은 결정립에 의해 심한 표면 거칠기를 나타낸다. 루비를 상대재료로 사용하여 하중 50g, 50rpm의 회전속도로 마모시험을 하였으며 마모 track의 직경은 100mm였다. 마찰계수는 0.5에서 계속 감소하며 0.1이하에서 안정한 상태를 유지하게 된다. 이 다이아몬드 박막위에 저마찰재료로 알려진 PTFE를 타겟으로 RF로 증착한 후 같은 조건으로 마모시험을 행하면 마찰계수가 초기부터 일정하게 유지할 수 있게 된다. 반면에 MoS2박막이 증착된 경우에는 완만한 마찰계수의 감소가 나타난다. 이러한 변화의 원인으로는 DLC 박막에서 보고되고 있는 바와 같이 다이아몬드의 sp3 결합구조가 마모시험중 흑연화하여 sp2 결합구조로 변하기 때문인 것인지 살펴보기 위하여 micro Raman을 통하여 마모 track을 분석하였고 AFM을 통하여 표면거칠기 변화와 표면 스크래치 발생 여부를 살펴보았다.

• Composites Research
• /
• v.16 no.4
• /
• pp.22-28
• /
• 2003

This article deals with the manufacture and test results of asbestos-free friction material for Aluminium at toy disk. In order to obtain optimum formulation, various formulations of fibres, matrix, modifiers, fillers, etc were designed and evaluated. The constant friction and brake dynamometer tests were performed to know weak and strong point for each friction material. The C21 formulation of various tested formulations exhibited superior friction constant(0.38∼38), fade rate (18%) by JASO C406 test mode and maximum wear 1.6 mm. disc wear 0.08 mm by JASO C427 test mode. The surface morphology of AL alloy disk(before and after test) was observed by Scanning Electron Microscope(SEM) and Image Analyzer.

• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.37 no.2
• /
• pp.95-101
• /
• 2024

This paper introduces an optimized design for a sensor bracket used to measure the wear amount of an automobile brake pad, based on a dynamic kriging surrogate model. During testing, the temperature of the brake pad can increase beyond 600℃, which often causes sensor malfunction. Therefore, it is essential to optimize the shape of the sensor bracket to minimize heat transfer. To reduce the computational cost of the optimization, the heat-transfer simulation is replaced by a dynamic kriging surrogate model. Dynamic kriging utilizes the best combination of correlation and basis functions and constructs an accurate surrogate model. Following optimization, the temperature of the sensor position decreases by 7.57%. The results from the surrogate model under optimum conditions are verified by a heat-transfer simulation, and the design optimization using a surrogate model is found to be effective.

• Journal of Korea Foundry Society
• /
• v.42 no.4
• /
• pp.255-260
• /
• 2022

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.36 no.7
• /
• pp.723-730
• /
• 2012

During the cold wire-drawing process, the diameter of a wire is reduced and the length of the wire is increased as the wire passes through the die. The pressure and sliding motion at the interface between the wire and die cause elastic recovery of the workpiece and friction and wear on the die. In addition, wire deformation and frictional heating raise the temperature of the wire and die, resulting in difficulty in manufacturing the drawn products according to a designated inner diameter of the die, deviating from the designated dimension or the inner diameter of the die. In this study, considering the die temperature distribution, the effects of dimensional changes of the drawn products were analyzed quantitatively; these changes are caused by the elastic deformation of the die, the elastic recovery of the workpiece, and the thermal deformation of both the die and the workpiece. It was confirmed that the elastic recovery of the workpiece influenced these changes the most. The initial dies considering these factors could avoid deviation from the designated dimension, and the desired drawn products were obtained by using the designed initial drawing dies.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.13 no.1
• /
• pp.36-40
• /
• 2003

The diamond-like nanocomposite (DLN) thin films were deposited on Si substrates using $CH_4/(C_2H_5O)_4Si/H_2$/Ar gas mixtures as source gases by the plasma enhanced chemical vapor deposition (PECVD). The chemical structure and microstructure of grown films were investigated and their tribological properties were evaluated by a ball-on-plate type tribometer. The deposited DLN films mainly consisted of diamond-like a-C:H and quartz-like a-Si:O networks. The DLN films had a good agreement with tribological coating applications due to their extremely low friction coefficients and low wear rates.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.20 no.1
• /
• pp.77-87
• /
• 2012

In this paper, the method and its effectiveness to decrease the uneven wear of the brake pad were proposed. A finite element analysis was performed to analyze the pressure distributions on the contact surfaces. The optimum brake pad shape was determined by a robust design using the Taguchi method. The effectiveness of the optimum design was clarified by the wear tests with a dynamometer.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.10 no.4
• /
• pp.199-205
• /
• 2002

This paper presents a numerical technique to analyze wear life of automotive disk brake pad, where FFT-FEM method is adopted to determine the transient temperature distribution of the disk surface. A specimen ova frictional material is tested on a small scale brake dynamometer to find the dependency of the wear rate on temperature change, from which and the temperature analysis results, given the wear test mode, wear behavior of the pad material fur the vehicle can be predicted. Numerical examples show the predicted wear life of the vehicle coincides with the manufacture's recommended time interval for replacing the pads.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.22 no.1
• /
• pp.8-19
• /
• 2014

In this paper, a robust design of the back-plate of the brake pad to decrease the uneven wear of the pad was studied. A finite element analysis was performed to analyze the pressure distributions on the contact surfaces. Optimized back-plate shape of the brake pad was determined using the Taguchi method. The effectiveness of the robust design was clarified by the wear tests with a dynamometer.