• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.27 no.4
• /
• pp.544-550
• /
• 2003

The contact analyses of arbitrary shaped spatial bodies are important in the study of multi-body dynamics. This paper presents a method fur calculating contact force between bodies in space. At each integration time step, the proposed method finds potential contact points on bodies and then calculates the penetration, the velocity of penetration, and the contact force. A continuous analysis method is adopted to calculate the contact force. To get contact points accurately on their outlines, a new algorithm is developed. The proposed algorithm is tested and compared the results of DADS. As applications, the contact of two steel balls, spatial pendulums, and the problem of a ball and bat are demonstrated.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2009.04a
• /
• pp.559-560
• /
• 2009

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2010.05a
• /
• pp.423-424
• /
• 2010

• Proceedings of the KSME Conference
• /
• 2003.04a
• /
• pp.874-880
• /
• 2003

Many mechanical systems are over-constrained if only rigid bodies are used to model the system. One example of such system is a satellite system with solar panels. To avoid this over-constrained problem, solar panels can be modeled as flexible bodies. The CMS(Component Mode Synthesis) method is widely used to analyze the flexible multi-body system because it can considerably approximate the deformation of the flexible bodies using small number of well-selected mode. However, it is very difficult to decide the boundary condition and the selection of modes. In this paper, the methods for mode synthesis and setting the boundary condition are presented to analyze the flexible multi-body system with over-constraints. Finally, the reliability of proposed method is verified by solar panel's deployment test.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.18 no.5
• /
• pp.541-549
• /
• 2008

The dynamic contact between a high-speed wheel and an elastic beam is numerically analyzed by solving the whole equations of motion of the wheel and the beam subjected to the contact condition. For the stability of the numerical solution, the velocity and acceleration constraints as well as the displacement constraint are imposed on the contact point. Through the numerical examples, it is shown that the acceleration contact constraint including the Coriolis and centripetal accelerations are crucial for the numerical stability.

• Proceedings of the KSME Conference
• /
• 2008.11a
• /
• pp.817-821
• /
• 2008

Wind turbine requires service life of about 20 years and each components of wind turbine requires high durability, because installation and maintenance costs are more expensive than generated electricity by wind turbine. So the design of wind turbine must be verified in various condition before production step. This paper demonstrates the application of a generic methodology, based on the flexible multibody simulation technique, for the dynamic analysis of a wind turbine and its drive train. The concern of the paper is the computation of dynamic loads of wind turbine in emergency-stop condition. The finite element model is used to analyse the dynamic behaviour of the wind turbine.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.38 no.1
• /
• pp.25-30
• /
• 2014

The dynamic characteristics of a gas circuit breaker depend on the underlying high-speed operating mechanism with a spring-actuated latch system. Many studies have been carried out to reduce the breaking time of circuit breakers. In this study, the optimum latch contour design is determined for reducing the breaking time of a circuit breaker. A multi-body dynamic model of the latch is established for analyzing the dynamic behaviors of the circuit breaker by using the MSC/ADAMS program. Simulation results are matched against experimental data. VisualDoc is employed for determining the optimal latch contour. From the optimum design, the breaking time of a gas circuit breaker is improved by about 8.6%.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.18 no.3
• /
• pp.26-32
• /
• 2019

This study was conducted to analyze the stresses by impact loads on front-end loaders attached to tractors using flexible multi-body dynamics. The model was designed and validated by comparing previous experimental data with the simulation data obtained in this study. Nine sets of conditions were designed using three weights (500, 300, and 100 kg) loaded inside a bucket and three heights (1700, 1350, and 1000 mm) of the bucket from ground level. A parametric study was carried out at five locations for two types of parts of a front-end loader. All the safety factors for the five locations under all conditions were calculated and were greater than 1. Thus, the designs of the front-end loaders were structurally safe. Based on this study, front-end loaders attached to tractors can be designed effectively in terms of cost and safety.

• Journal of Ocean Engineering and Technology
• /
• v.7 no.2
• /
• pp.141-149
• /
• 1993

삼 자유도를 가진 부유물체의 동적 응답을 이론적으로 연구하였다. 평면내 방향 운동모우드에 대한 지배방정식을 선형화한 후, 그들의 조화해를 평명밖 방향 운동모우드의 방정식과 연성시켰다. 그렇게 해서 주어지는 방정식은 시간에 따라 변화하는 계수를 가진 형태로서, 평면밖 방향의 운동만을 보일 것으로 예측되는 부유물체가 평면밖 방향의 운동을 보일 수도 있음을 밝혔다. 동역학적 불안정성과 그 결과로 나타나는 평면밖 방향의 대진폭 운동을 보이고 있다. 본 결과는 주기적으로 동요하는 부유물체가 서로 연성된 운동을 하는 현상으로도 해석할 수 있다.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2007.11a
• /
• pp.409-414
• /
• 2007

Nowadays, with the advancement of computational mechanics, and vehicle dynamics simulation linked up with virtual testing laboratory(VTL) and virtual proving ground(VPG) technologies has become a useful method for analyzing numerous driving performances and diverse noise/vibration characteristics. In this paper, the analytical vehicle model based on multi-body dynamics theory was developed to investigate the vibration characteristics according to various road conditions. For the purpose, the whole vehicle parameters, each vehicle's part parameter, and part connecting elements such as spring, damper, and bush were measured by an experiment. Also, the vehicle dynamics model, which includes the front suspension, rear suspension, steering, front wheel, rear wheel, and body subsystems has been constructed for computer simulation. With the developed vehicle dynamics model, three forces and three moments measured at each wheel center were applied to evaluate and analyze dynamics and vibration characteristics for miscellaneous road conditions.