• Journal of Drive and Control
• /
• v.11 no.2
• /
• pp.22-29
• /
• 2014

This paper presents simulation-based analysis of energy flow of a wheel loader. The objective of this study is to analyze the energy flow of a wheel loader during driving and working. Because the wheel loader powertrain consists of a mechanical and hydraulic powertrain, the generated power from the engine is divided into 2 powertrains. Further, a virtual prediction of energy flow in the powertrains is a key factor in terms of optimal design. Accordingly, the simulation model that is able to predict the virtual energy flow is developed and analyzed in this study. The proposed wheel loader simulation model has been constructed in the Matlab/Simulink environment. It is expected that the developed simulation model will analyze the energy flow and efficiency in the design stage.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.36 no.4
• /
• pp.437-442
• /
• 2012

To analyze a multibody system, this paper proposes an implicit numerical integration method for joint coordinates subsystem synthesis method. To verify the proposed method, a multibody model for an unmanned robot vehicle, which consists of six identical independent suspension systems, is developed. The symbolic method is applied to compute the system Jacobian matrix for the implicit integration method. The proposed method is also verified by performing rough terrain run-over simulation in comparison with the conventional implicit integration method. In addition, to evaluate the efficiency of the proposed method, the CPU time obtained by using this method is compared with that obtained by using the conventional implicit method.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.10 no.4
• /
• pp.106-113
• /
• 2002

A procedure to model and simulate control systems is presented using CADyna and MATLAB/Simulink computer codes. For the plant modeling, a technique for obtaining the state matrices from CADyna is presented. To obtain state matrices from CADyna models, perturbation theory is used. These state matrices are then used in NATLAB to design a controller for the plant. The controller design can subsequently be incorporated into the CADyna model and its closed loop performance is evaluated. Examples are presented to verify the developed methodology.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.38 no.5
• /
• pp.575-584
• /
• 2014

In this study, the NREL 5 MW wind turbine tower model was optimized according to the multi-body dynamics and reliability-based design. The mathematical model was defined as a link-joint system including dynamic characteristics derived from Timoshenko's beam theory. For the optimization problem, the sensitivities to variations in the tower thicknesses and inner and outer diameters were acquired and arranged in terms of safety and efficiency according to bending stress and buckling standards. An optimal design was calculated with the advanced first-order second moment method and used to define a finite element model for validation. The finite element model was simulated by static analysis. The relationship between the multi-body dynamic and finite element method throughout the process was investigated, and the optimal model, which had high endurance despite its low mass, was determined.

• Journal of Aerospace System Engineering
• /
• v.12 no.1
• /
• pp.1-9
• /
• 2018

In this study, a hybrid control method that adjusts for the existing force control technique has been presented for consideration. The proposed hybrid control technique does away with the chattering phenomenon occurring in existing force control technique and provides high shock absorption efficiency. In order to design the controller for the landing gear with MR damper, the equation of motion of the landing gear was derived. The hybrid controller was designed after constructing a simulation model using Recur-Dyne, multi-body dynamic analysis software. The hybrid controller can reduce the maximum strut force and displacement based on the skyhook controller, and is able to get the high efficiency by making it work for the additional force control technique. In addition, an effective switching control technique and input shaping technique was applied to prevent the chattering in the drop simulation. Finally, the performance of the landing characteristics was evaluated throughout the various drop simulations.

• Journal of the Korean Society for Railway
• /
• v.18 no.3
• /
• pp.175-185
• /
• 2015

Generally, in the train area, switch tracks have required high reliability because this system is directly associated with derailment. Especially, switch tracks of Maglev vehicles must be moved in terms of the whole geometric characteristics, in which the bogies are encased in the switch track. For this reason, switch track was constructed with steel lighter than concrete girders. But, the steel switch track was weak because of structural vibration as well as structural deformation. Therefore, it is important to predict the levitation stability when a vehicle passes over flexible switch track. The aims of this paper are to develop a coupled dynamic model to describe the relationship between a Maglev vehicle and switch track and to predict the levitation stability. In order to develop the coupled dynamic model, a three dimensional vehicle model was developed based on multibody dynamics; a switch model was made using the modal superposition method. And, the developed model was verified using comparison measured data.

• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.26 no.4
• /
• pp.247-254
• /
• 2013

In this paper, dynamic response analysis of a heave compensation system is performed for offshore drilling operations based on multibody dynamics. With this simulation, the efficiency of the heave compensation system can be virtually confirmed before it is applied to drilling operations. The heave compensation system installed on a semi-submersible platform consists of a passive and an active heave compensator. The passive and active heave compensator are composed of several bodies that are connected to each other with various types of joints. Therefore, to carry out the dynamic response analysis, the dynamics kernel was developed based on mutibody dynamics. To construct the equations of motion of the multibody system and to determine the unknown accelerations and constraint forces, the recursive Newton-Euler formulation was adapted. Functions of the developed dynamics kernel were verified by comparing them with other commercial dynamics kernels. The hydrostatic force with nonlinear effects, the linearized hydrodynamic force, and the pneumatic and hydraulic control forces were considered as the external forces that act on the platform of the semi-submersible rig and the heave compensation system. The dynamic simulation of the heave compensation system of the semi-submersible rig, which is available for drilling operations with a 3,600m water depth, was carried out. From the results of the simulation, the efficiency of the heave compensation system were evaluated before they were applied to the offshore drilling operations. Moreover, the calculated constraint forces could serve as reference data for the design of the mechanical system.

• Journal of the Korean Society of Industry Convergence
• /
• v.27 no.4_2
• /
• pp.943-951
• /
• 2024

This paper considers the simulation-based installation and operation safety analysis of installation and operation machinery of USBL as underwater equipment in operation environments. The simulation model of this mechanical system was developed using flexible multibody dynamics simulation technology. Operation and environmental conditions were applied using dynamic forces model considering ocean environments. The developed simulation model was used to evaluate operation safety through eigenvalue analysis, dynamic forces analysis, and structural analysis. As the analysis results, the operation safety was very low in extreme operation condition due to increase of dynamic loads by VIV effect. It was not a problem because safety factor had more than 2.0 in this case. However, the operation safety should be further strengthened because the USBL and LARS was installed and utilized in unmanned vessel with automatic controls. In order to improve safety by avoiding VIV frequency, we redesigned the USBL pole.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.40 no.7
• /
• pp.685-692
• /
• 2016

A cutting head is an attachment on the front of an excavator that cuts or grinds rocks. Cutting tools, called pick cutters, are arranged on the surface of the cutting head. The exact arrangement and configuration of pick cutters is one of the most important factors in determining grinding efficiency. This study focuses on the problem of automation for pick arrangement design, in order to make the design process more efficient and convenient. Design automation was carried out using RecurDyn/ProcessNet, and it was composed of three parts: 'Drum set', 'Pick load', and 'Pick arrangement' sections. The presented method helps to decrease costs attributed to designing cutting heads and can be used to generate a wide range of attachment mechanisms.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.44 no.12
• /
• pp.1087-1094
• /
• 2016

The responsibility of the vehicle holding device (VHD) is to hold the launch vehicle while it is stayed on launch pad and release the holding mechanism to allow a lift-off of launch vehicle at a moment of lift-off. During a release of the holding mechanism, in order to prevent the Ka doing a doing a doing mode which is vertical oscillation of entire liquid propellant and very severe for vehicle structure, gradual release of holding force is required. Also, a release operation of all 4 VHD should be synchronized very precisely. In this study, to comply the "gradual release and synchronized operation requirement", concept of VHD hydraulic system using an accumulator, pyro valve and orifice to control speed of hydraulic cylinder is proposed instead of using complicated hydraulic components. Then through multi-body dynamic analysis and computational hydraulic analysis, a size of orifice to meet a target speed of hydraulic cylinder is calculated. Through this study, simple and reliable VHD hydraulic system complying requirements is designed.