• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.39 no.5
• /
• pp.433-441
• /
• 2011

The optimization of a centrifugal compressor was conducted. The ANN (Artificial Neural Network) was adopted as an optimization algorithm, and it was learned and trained with the DOE (Design of Experiment). In the DOE, it was predicted the main effect and the interaction effect of design variables to the objective function. The ANN was improved in the optimization process using the GA (Genetic Algorithm). When any output at each generation was reached a standard level, it was re-calculated by the CFD (Computational Fluid Dynamics) and it was applied to develop a new ANN. After 6th generation, the prediction difference between ANN and CFD was less than 1%. A pareto of the efficiency versus the pressure ratio was obtained through the 21th generation. Using this method, the computational time for the optimization was equivalent to the time consumed by the gradient method, and the optimized results of multi-objective function were obtained.

• Journal of the Korean Institute of Intelligent Systems
• /
• v.15 no.3
• /
• pp.375-381
• /
• 2005

Usually genetic algorithms are used to design optimal system. However the performance of the algorithm is determined by the fitness function and the system environment. It is expected that a co-evolutionary algorithm, two populations are constantly interact and co-evolve, is one of the solution to overcome these problems. In this paper we propose three types of co-evolutionary algorithm to solve GA-Hard problem. The first model is a competitive co-evolutionary algorithm that solution and environment are competitively co-evolve. This model can prevent the solution from falling in local optima because the environment are also evolve according to the evolution of the solution. The second algorithm is schema co-evolutionary algorithm that has host population and parasite (schema) population. Schema population supply good schema to host population in this algorithm. The third is game model-based co-evolutionary algorithm that two populations are co-evolve through game. Each algorithm is applied to visual servoing, robot navigation, and multi-objective optimization problem to verify the effectiveness of the proposed algorithms.

• Proceedings of the KIEE Conference
• /
• 2000.07a
• /
• pp.233-235
• /
• 2000

SVC(Static Var Compensator) is commonly installed with conventional mechanically switched existing reactor or capacitor banks for wide range voltage control. The frequencies of switching of external banks have a great impact on the quality of voltage, but is limited since the life time of the external banks depends severely on the number of switching. So it is a complete multi-objective nonlinear optimization problem with conflicting objectives. This paper presents a method to determine the optimal coordination of SVC and external banks using genetic algorithm based on the multi-objective criteria. Optimal dead band and delay time of external banks is sought for reliable and efficient operation

• IE interfaces
• /
• v.20 no.4
• /
• pp.504-514
• /
• 2007

The multicast routing problem lies in the composition of a multicast routing tree including a source node and multiple destinations. There is a trade-off relationship between cost and delay, and the multicast routing problem of optimizing these two conditions at the same time is a difficult problem to solve and it belongs to a multi-objective optimization problem (MOOP). A multi-objective genetic algorithm (MOGA) is efficient to solve MOOP. A micro-genetic algorithm(${\mu}GA$) is a genetic algorithm with a very small population and a reinitialization process, and it is faster than a simple genetic algorithm (SGA). We propose a multi-objective micro-genetic algorithm (MO${\mu}GA$) that combines a MOGA and a ${\mu}GA$ to find optimal solutions (Pareto optimal solutions) of multicast routing problems. Computational results of a MO${\mu}GA$ show fast convergence and give better solutions for the same amount of computation than a MOGA.

• 한국신재생에너지학회:학술대회논문집
• /
• 2011.05a
• /
• pp.58.2-58.2
• /
• 2011

본 연구에서는 5MW급 수평축 풍력터빈 블레이드에 대해 국내 서남해안의 풍속특성을 고려한 최적설계를 수행 하였다. 최적설계를 수행하기 위해 블레이드 해석은 Blade Element and Momentum Theory를 이용 하였으며, 설계 시 적용된 기저형상은 NREL에서 제안한 5MW급 풍력터빈 블레이드을 선정하였다. 최적설계를 수행하기 전 설계에 사용된 설계변수들이 풍속에 대해 어떠한 경향을 가지고 있는지 알아보기 위해 Parametric Study를 수행 하였으며, 최적설계는 다목적 최적화 유전 알고리즘인 NSGA-II를 이용하여 평균풍속이 낮은 서남해안의 연간에너지 생산량과 설비이용률을 최대화하였다. 최적화 결과들로부터 설계 조건에 맞는 최적해를 도출 할 수 있었으며, 이를 통해 기저형상의 연간에너지 생산량 및 설비이용률을 보다 향상 시킬 수 있었다.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.48 no.6
• /
• pp.411-418
• /
• 2020

In this paper, approximation and optimization methods are proposed for the structural performance of the composite fan blade. Using these methods, we perform the optimal design of the stacking sequence to maximize stiffnesses without changing the mass and the geometric shape of the composite fan blade. In this study, the lamination parameters are introduced to reduce the design variables and space. From the characteristics of lamination parameters, we generate response surface model having a high fitness value. Considering the requirements of the optimal stacking sequence, the multi-objective optimization problem is formulated. We apply the two-step optimization method that combines gradient-based method and genetic algorithm for efficient search of an optimal solution. Finally, the finite element analysis results of the initial and the optimized model are compared to validate the approximation and optimization methods based on the lamination parameters.

• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.24 no.2
• /
• pp.157-165
• /
• 2011

Base isolation system is widely used for reduction of dynamic responses of structures subjected to seismic load. Recently, research on a smart base isolation system that can effectively reduce dynamic responses of the isolated structure without accompanying increases in base drifts has been actively conducted. In this study, a smart base isolation system was applied to an arch structure subjected to seismic excitation and its control performance for reduction of seismic responses was evaluated. In order to make a smart base isolation system, 4kN MR dampers and low damping elastomeric bearings were used. Seismic response control performance of the proposed smart base isolation system was compared to that of the optimally designed lead-rubber bearing(LRB) isolation system. To this end, an artificial ground motion developed based on KBC2009 design response spectrum was used as a seismic excitation. Fuzzy control algorithm was used to control MR damper in the smart base isolation system and multi-objective genetic algorithm was employed to optimize the fuzzy controller. Based on numerical simulation results, it has been shown that the smart base isolation system can drastically reduce base drifts and seismic responses of the example arch structure in comparison with LRB isolation system.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.42 no.2
• /
• pp.108-118
• /
• 2014

On the optimization design problem using surrogate model, it requires considerable number of sampling points to construct a surrogate model which retains the accuracy. As an alternative to reduce construction cost of the surrogate model, Variable-Fidelity Modeling(VFM) technique, where correct high fidelity model based on the low fidelity surrogate model is introduced. In this study, hierarchical kriging model for variable-fidelity surrogate modeling is used and an optimization framework with multi-objective genetic algorithm(MOGA) is presented. To prove the feasibility of this framework, airfoil design optimization process is performed for the transonic region. The parameters of PARSEC are used to design variables and the optimization process is performed in case of varying number of grid and varying fidelity. The results showed that pareto front of all variable-fidelity models are similar with its single-level of fidelity model and calculation time is considerably reduced. Based on computational results, it is shown that VFM is a more efficient way and has an accuracy as high as that single-level of fidelity model optimization.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.40 no.9
• /
• pp.557-567
• /
• 2016

In this study, the optimal design of heat exchangers, including the evaporator and condenser of a solar-heating ocean thermal energy conversion (SH-OTEC), is investigated. The power output of the SH-OTEC is assumed to be 100 kW, and the SH-OTEC uses the working fluid of R134a and high-performance commercial tubes. The surface heat transfer area and the pressure drop were strongly dependent on the number of tubes, as well as the number of tube passes. To solve the reciprocal tendency between the heat transfer area and pressure drop with respect to the number of tubes, as well as the number of tube passes, a genetic algorithm (GA) with two objective functions of the heat transfer area (the capital cost) and operating cost (pressure drop) was used. Optimal results delineated the feasible regions of heat transfer area and operating cost with respect to the pertinent number of tubes and tube passes. Pareto fronts of the evaporator and condenser obtained from multi-objective GA provides designers or investors with a wide range of optimal solutions so that they can select projects suitable for their financial resources. In addition, the surface heat transfer area of the condenser took up a much higher percentage of the total heat transfer area of the SH-OTEC than that of the evaporator.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.11 no.12
• /
• pp.4697-4706
• /
• 2010

This paper suggested the optimal operating design method using simulation and ANP(Analytic Network Process) for mass-customization in the automotive component manufacturing industry. For this, first of all, we built the simulation model including various and complex factors in the field, and estimated the meta-model by RSM(Response Surface Method). Secondly using ANP, we calculated the weight of relative importance of evaluation factors gathered from decision makers. And then, we proposed the optimal operation designs by MOGA(Multi-Objective Genetic Algorithm), analyzed results of them. Moreover, by comparing the results with the consequences using AHP(Analytic Hierarchy Process), we showed its superiority of suggested method to the manner using AHP, because it reflects inner, outer dependency, and inter-relation among judgement factors. In conclusion, through this process, we can present the better way to serve mover effective, precise, and accurate information to decision makers when they build operation design for mass-customization system as automotive parts production system.