• Journal of the Korean Electrochemical Society
• /
• v.14 no.3
• /
• pp.157-162
• /
• 2011

The stability at elevated temperatures of a surface film formed on a graphite electrode in lithium secondary batteries was investigated by transmission electron microscopy (TEM) and electrochemical AC impedance spectroscopy (EIS). TEM analysis revealed that the surface film partly dissolved in the electrolyte solution during storage at $60^{\circ}C$, resulting in a decrease in the thickness of the surface film and a change in its morphology to a porous structure. On the other hand, an increase in the impedance of the surface film which is attributable to a change in composition of the surface film was confirmed by EIS analysis during the storage at $60^{\circ}C$. It was also shown that the addition of vinylene carbonate or 1,3-propane sultone or etylene sulfite, even if limited, improves the stability of the surface film at elevated temperatures.

• Journal of the Korean institute of surface engineering
• /
• v.28 no.5
• /
• pp.276-288
• /
• 1995

A nickel mesh and an expanded nickel sheet were used as a current collector for supporting active materials of cathode in rechargeable batteries, while a porous nickel substrate was extensively studied because of its 3-dimensional structure which has high capabilities for active materials and current collection. Optimum coating conditions were studied by SEM and two step d. c. constant current electrolysis for the graphite coating and electro-plated nickel on an urethane substance which was highly porous and 3-dimensional structure. The density and the porosity of nickel support obtained by using two step current density and 80 ppi urethane substance were 0.38∼0.40 g /㎤ and 94∼96%, respectively. It was possible to fabricate a highly porous and good packable nickel substrate using two step current density and surfactants at sulfamic acid nickel plating bath.

• Korean Journal of Materials Research
• /
• v.28 no.3
• /
• pp.189-194
• /
• 2018

Porous graphites were synthesized by removing the template in HF after cabothermal conversion for 3 h at $900^{\circ}C$, accompanied by intercalations of pyrolyzed fuel oil (PFO) in the interlayer of Co or Ni loaded magadiite. The X-ray powder diffraction pattern of the porous graphites exhibited 00l reflections corresponding to a basal spacing of 0.7 nm. The particle morphology of the porous graphites was composed of carbon plates intergrown to form spherical nodules resembling rosettes like a magadiite template. TEM shows that the cross section of the porous graphites is composed of layers with very regular spaces. In particular, crystallization of the porous graphite was dependent on the content of Co or Ni loaded in the interlayer. The porous graphite had a surface area of $328-477m^2/g$. This indicates that metals such as Co and Ni act as catalysts that accelerate graphite formation.

• 한국신재생에너지학회:학술대회논문집
• /
• 2009.11a
• /
• pp.230-230
• /
• 2009

In this work, Porous Carbons (PCs) were prepared by using a chemical acid treatment, and the hydrogen storage behaviors of PCs doped by Pt nanoparticles were investigated. The hydrogen storage capacities of the Pt-doped carbons with a platinum content of 0.2 - 1.5 wt.% were evaluated by a volumetric adsorption method at 298K and 10 MPa. The microstructures of samples were examined by XRD and SEM. It was found that the hydrogen storage capacitiesof the PCs dramatically increased, but the amount of hydrogen stored from the samples began to decrease after 0.6 wt.% of Pt content due to the pore blocking. These results indicate that a suitable amount of supported catalysts and layer intervals of carbons had a very important impact on hydrogen storage behaviors.

• Journal of Powder Materials
• /
• v.12 no.2 s.49
• /
• pp.151-158
• /
• 2005

Porous graphite was synthesized by removal of template in HF after pyrolysis of pyrolyzed fuel oil (PFO) at $900^{\circ}C$ using the template of Co or Ni intercalated magadiite. Porous graphite had a plate structure like template, and d-spacing value of about 0.7 nm. The extent of crystallization of porous graphite was dependent on the contents of Co or Ni intercalated in interlayer. It can be explained that the metal such as Co and Ni acts as a promotion catalyst for graphite formation. Porous graphite shows the surface area of $328\sim477 m^2/g$.

• Applied Chemistry for Engineering
• /
• v.19 no.2
• /
• pp.185-190
• /
• 2008

In order to increase the surface area of electrodes for electrosorption, porous carbon electrodes were fabricated by a wet phase inversion method. A carbon slurry consisting of a mixture of activated carbon powder (ACP), polyvinylidene fluoride (PVdF), and N-methyl-2-pyrrolidone (NMP) as a solvent was cast directly on a graphite sheet. The cast film was then immersed in pure water for phase inversion. The physical and electrochemical properties of the electrodes were investigated using scanning electron microscopy (SEM), porosimetry, and cyclic voltammetry. The SEM images verified that the pores of various sizes were formed uniformly on the electrode surface. The average pore sizes determined for the electrodes fabricated with various NMP contents ranged from 64.2 to 82.4 nm and the size increased as the NMP content increased. All of the voltammograms showed a typical behavior of charging and discharging characteristic at the electric double layer. The electrical capacitance ranged from 3.88 to $5.87F/cm^2$ depending on the NMP contents, and the electrical capacitance increased as the solvent content decreased. The experimental results showed that the solvent content is an important variable controlling pore size and ultimately the capacitance of the electrode.

• Journal of Korean Society of Environmental Engineers
• /
• v.30 no.4
• /
• pp.409-414
• /
• 2008

Porous carbon electrode for electrosorption was prepared by a wet phase inversion method. Carbon slurry that was a mixture of activated carbon powder(ACP) and PVdF solution was cast directly upon a graphite sheet by means of a casting knife. Porous carbon electrodes were fabricated by immersing the cast film in pure water as a non solvent. Physical and electrochemical properties of carbon electrodes prepared with various ACP contents(50.0, 75.0, 83.3, 87.5, 90.0 wt %). From the SEM images we can verify that the electrode was porous. The average pore sizes determined for the electrodes fabricated with various ACP contents ranged from 72.7 to 86.4 nm and the size decreased as the ACP content increased. The electrochemical properties were characterized by cyclic voltammetry(CV) method. All of the voltammograms showed typical behavior of an electric double layer charging/discharging on the carbon surface. The capacitance increased with the ACP content and the values ranged from 2.18 F/cm$^2$ for 50 wt% ACP to 4.77 F/cm$^2$ for 90 wt% ACP.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2015.08a
• /
• pp.239.1-239.1
• /
• 2015

1차원 탄소나노재료이며 한 겹의 흑연을 말아 놓은 형태인 단일벽 탄소나노튜브(Single-walled carbon nanotubes, SWNTs)는 감긴 형태에 따라 반도체성, 금속성 성질을 나타내는 특이성과 우수한 기계적 성질을 지니고 있어 광범위한 분야로 응용이 기대되어왔다. 이러한 SWNTs의 응용가능성을 실현시키기 위해서는 보다 경제적, 산업적인 면에서 손쉬운 합성방법의 개발이 필요한 실정이다. SWNTs의 합성 방법들로는 아크방전법과 레이저 증발법, 그리고 열화학기상증착법(Thermal chemical vapor deposition, TCVD) 등이 이용되었다. 이 중 TCVD법은 대면적의 균일한 CNTs를 합성할 수 있다는 장점이 있다. 그러나 탄화수소가스를 효율적으로 분해하기 위하여 $800^{\circ}C$ 이상의 고온 공정이 요구되며, 이는 경제적, 산업적인 면에서 사용이 제한적이다. 따라서 저결함, 고수율의 SWNTs를 저온합성 할 수 있는 공정의 개발이 지속적으로 필요하다. 본 연구에서는, TCVD법을 이용하여 에틸렌 원료가스로 SWNTs의 저온합성 가능성을 확인하였다. 합성을 위한 기판과 촉매로는 실리콘 산화막 기판(SiO2/Si wafer)에 철 나노입자를 지닌 ferritin을 스핀코팅 후 산화하여 이용하였다. 저온합성 공정의 변수로는 합성온도와 원료가스인 에틸렌의 분율을 설정하여, 변수가 SWNTs의 결정성과 수율에 미치는 영향을 고찰하였다. 합성된 SWNTs의 분석의 용이함과 손지기(Chirality)의 제어를 위하여 나노 다공성 물질인 제올라이트(Zeolite)를 보조 기판으로 사용하였다. 실험결과 에틸렌 원료가스로 합성한 SWNTs는 $700^{\circ}C$ 부근의 저온에서도 합성이 가능함을 확인하였다. 또한 에틸렌 원료가스의 분율과 합성시간의 정밀한 제어를 통해 SWNTs의 합성온도를 더욱 감소시키는 것도 가능할 것으로 예상된다.

• Journal of the Korean institute of surface engineering
• /
• v.49 no.1
• /
• pp.104-109
• /
• 2016

Graphite's thermal stability facilitates its widespread use as crucibles and molds in high temperatures processes. However, carbon atoms can be rather easily detached from pores and outer surfaces of the graphite due to the weak molecular force of the c axis of graphites. Detached carbon atoms are known to become a source of dust during fabrication processes, eventually lowering the effective yield of products. As an effort to reduce these problems of dust scattering, we have fabricated SiC composites by employing Si vapor infiltration method into the pores of graphites. In order to understand the diffusion process of the Si vapor infiltration, Si and C atomic percentages of fabricated SiC composites are carefully measured and the diffusion law is used to estimate the diffusion coefficient of Si vapor. A quadratic equation is obtained from the experimental results using the least square method. Diffusion coefficient of Si vapor is estimated using this quadratic equation. The result shows that the diffusion length obtained through the Si vapor infiltration method is about 10.7 times longer than that obtained using liquid Si and clearly demonstrates the usefulness of the present method.

• Applied Chemistry for Engineering
• /
• v.8 no.2
• /
• pp.161-171
• /
• 1997

Anodic regeneration of PCB enchant and cathodic deposition of copper using electrochemical method has been studied. Cu(I)/Cu(II) concentration ratio as a function of Cu(I) oxidation at the anode was measured from the potential difference between platinum and Ag/AgCl/4M KCl electrodes. Chlorine gas evolution was minimized by maintaining Cu(I) concentration above a specific concentration and using non-porous graphite electrode. Dendritic copper deposition was observed at the cathode and the optimum conditions for Cu deposition was identified as the current density of $360mA/cm^2$, and copper concentration of 12 g/l. Titanium was the most effective cathode material which showed a higher current efficiency and copper recovery. The current efficiency decreased with increasing temperature, but the highest power efficiency was achieved at $50^{\circ}C$.