• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.20 no.4
• /
• pp.93-99
• /
• 2019

The purpose of this study was to investigate the bond strength between PEKK(Polyetherketoneketone) and Sinfony(3M ESPE, Seefeld, Germany) the dental composite resin by proposing the three representative surface treatment methods and evaluate to see if they affect the bond strength between two materials. A total of 30 PEKK($Pekkton^{(R)}$ Ivory, $Cendres+M{\acute{e}}taux$, Bienne, Switzerland) specimens were prepared, embedded in acrylic resin, polished(P 1200 grid) to surface, and each group was divided into 10 specimens. After then, by the surface treatment method, it classified into three groups(n=10) such as Air abrasion group(PN), applying Single Bond Universal(3M ESPE) after Air abrasion(PB), applying OPAQUE(3M ESPE) after Air abrasion(PO). Then, veneering was performed by using Sinfony(3M ESPE, Seefeld, Germany). All completed specimens were allowed to rest in a $37^{\circ}C$ water bath for 24 hours. Shear bond strength of each group was measured and fracture patterns were classified. Statistic analysis was performed with One-way ANOVA followed by post hoc Scheffe tast (p<.05). Statistical analysis was performed using the SPSSWIN 21.0 program. As a result of one-way ANOVA, the average value of PB group was $27.67{\pm}4,18MPa$ and it was shown as the highest bond strength, PN and PO were $20.43{\pm}1.70$ and $19.8{\pm}4.77MPa$ each, and these were relatively low(F=18.4, P<.001), and as the post-test the Scheffe test was conducted and verified (p<.05). After examining the scheffe test, it was showed significant differences as PB>PO, PB>PN(p<.001). Through this study, in order to enhance the bonding force between PEKK and the composite resin, perform the Air abrasion and surface treatment by using Single Bond Universal(3M ESPE) is recommended, and as coMPared with other studies. And it is assumed that the increase of the application time of the Air abrasion affects the increase of the shear bond strength. Thus, further research is required.

• The Journal of the Korea Contents Association
• /
• v.19 no.6
• /
• pp.620-631
• /
• 2019

Be an important competitive appearance for both boys and girls in modern society, and highlight the importance of enhancing their appearance. Administrative activity is considered traditionally feminine behavior and appearance, almost all female is subject of a consumer market is continuing, and recognition, but since the 1990s.Gender role stereotypes and women's social activity due to changes in status and role of men and women affected. Accordingly, the men in the realm of women than it used to be a glass half full and inclusive attitude began to improve her appearance are also men, and well in yourself. Investing a lot of time and money to their appearance to describe behavior. Furthermore, workers men to appearance factor for the career achievement, such as promotion or salary competitiveness is gradually spreading awareness of social life on whose behalf the men. The halo effect for a positive image formation and desirable looks to be. A Study on the self-wor Second, the higher the self-esteem of psychologically stable social approval of the important aesthetic of clothing, is less dependent on increased manageability and clothing. The study by analysis of the self respect persimmon and appearance for his own body satisfaction and a high correlation study and OK. Interpersonal and that a significant impact on the formation.Be an important competitive appearance for both boys and girls in modern society, and highlight the importance of enhancing their appearance. Administrative activity is considered traditionally feminine behavior and appearance, almost all female is subject of a consumer market is continuing, and recognition, but since the 1990s.Gender role stereotypes and women's social activity due to changes in status and role of men and women affected. Accordingly, the men in the realm of women than it used to be a glass half full and inclusive attitude began to improve her appearance are also men, and well in yourself. Investing a lot of time and money to their appearance to describe behavior. Furthermore, workers men to appearance factor for the career achievement, such as promotion or salary competitiveness is gradually spreading awareness of social life on whose behalf the men. The halo effect for a positive image formation and desirable looks to be. A Study on the self-wor Second, the higher the self-esteem of psychologically stable social approval of the important aesthetic of clothing, is less dependent on increased manageability and clothing. The study by analysis of the self respect persimmon and appearance for his own body satisfaction and a high correlation study and OK. Interpersonal and that a significant impact on the formation.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.20 no.8
• /
• pp.200-206
• /
• 2019

Korea is introducing new animal welfare rearing standards for swine farmers in order to improve the breeding environment of livestock on Korean farms, Korea is establishing a policy to apply to all new farms in 2019 and to all existing farms in 2025. These guidelines are limiting stall breeding of sows after 4 weeks of pregnancy, the light intensity should be above 40lux, the ammonia level should be below 25ppm and the breeding density area should be increased from $1.4m^2$ to $2.25m^2$. In Europe, where animal welfare has been studied and applied for nearly 100 years, the facility specifications and management manuals are available and provided to farmers to introduce proper animal welfare for pigs and to enhance the convenience and utility of farmers who are converting to raising pigs. The EU has established independent standards for each country, and the EU has set the standards for floor facilities to improve animal welfare on pig farms and as applied by farmers. Yet in Korea, there are no methods and techniques for breeding methods that do not use an ordinary stall, except on a few leading farms. There has been no research on the welfare of sows so that farmer could improve sows' living conditions. Thus, farmers can minimize the difficulty of implementing the changing government policies, and they must develop farm turnover policies and specification management manuals to cope with the introduced regulations on sow group housing. We suggest that conducting research and evaluating the level of sows' welfare are important for farmers.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.20 no.1
• /
• pp.278-283
• /
• 2019

3 kinds of fine powder, Fe-2%Ni alloy powder(N Ltd.) and Fe+2%Ni mixed powder(B Ltd. and S Ltd.), were fabricated into sintered compacts of bending strength specimens and ring type specimens by metal injection molding, debinding and controlling sintering conditions (reduction and sintering atmospheres, sintering temperature, sintering time and cooling rates). Density and magnetic properties of the sintered compacts were evaluated with the following conclusions. (1) When each compact was hold at 1123K for 3.6ks in H2 and sintered at 1623K for 14.4ks in Ar, the density of N, B and S Ltd.'s sintered compacts were measured as 96, 99 and 99%, and oxygen/carbon contents were measured as 0.0041%O/0.0006%C, 0.0027%O/0.0022%C, and 0.160%O/0.0026%C, respectively. (2) Magnetic characteristics of B Ltd. compact in Ar with the best results showed $B_{25}=14.3KG$, $B_r=7.75KG$, and $H_c=2.1Oe$, but not enough as those made by melting process. (3) Magnetic properties of B Ltd. compact which were sintered at 1673K for 14.4ks in Ar gas, and cooled at $0.83Ks^{-1}$ to 1123K and then cooled at $0.083Ks^{-1}$ down to room temperature were measured as $B_{25}=14.8KG$, $B_r=8.3KG$, and $H_c=1.3Oe$, almost similar to those made by melting process. Objected soft magnetic materials properties were obtained through sintering process by controlling sintering conditions (reduction condition, sintering atmosphere, sintering temperature and sintering time) and cooling rates.

• Journal of Korean Tunnelling and Underground Space Association
• /
• v.20 no.6
• /
• pp.1125-1146
• /
• 2018

Segment lining applied to the TBM tunnel is mainly made of concrete, and it requires sufficient structural capacity to resist loads received during the construction and also after the completion. When segment lining is design to the Limit State Design, both Ultimate Limit State (ULS) and Service Limit State (SLS) should be met for the possible load cases that covers both permanent and temporary load cases - such as load applied by TBM. When design segment lining, it is important to check structural capacity at the joints as both temporary and permanent loads are always transferred through the segment joints, and sometimes the load applied to the joint is high enough to damage the segment - so called bursting failure. According to the various design guides from UK (PAS 8810, 2016), compression stress at the joint surface can generate bursting failure of the segment. This is normally from the TBM's jacking force applied at the circumferential joint, and the lining's hoop thrust generated from the permanent loads applied at the radial joint. Therefore, precast concrete segment lining's joints shall be designed to have sufficient structural capacity to resist bursting stresses generated by the TBM's jacking force and by the hoop thrust. In this study, bursting stress at the segment joints are calculated, and the joint's structural capacity was assessed using Leonhardt (1964) and FEM analysis for three different design cases. For those three analysis cases, hoop thrust at the radial joint was calculated with the application of the most widely used limit state design codes Eurocode and AASHTO LRFD (2017). For the circumferential joints bursting design, an assumed TBM jack force was used with considering of the construction tolerance of the segments and the eccentricity of the jack's position. The analysis results show reinforcement is needed as joint bursting stresses exceeds the allowable tensile strength of concrete. This highlights that joint bursting check shall be considered as a mandatory design item in the limit state design of the segment lining.

• Journal of the Korean Applied Science and Technology
• /
• v.35 no.4
• /
• pp.1456-1471
• /
• 2018

This article discusses the nutritional requirements, reviews senior or geriatric dog nutritional evaluation, and then addresses some common nutrition-related problems in older dogs. The purpose of this study was to investigate the Physiologic change associated with aging, essential nutrients and their diseases in senior or geriatric dog subjects. According to a 2002 market research, 30% to 40% of dogs raisedin the United States are 7 years of age. In Europe the number of dogs considered to be "senior or geriatric" (>7 years of age) increased by approximately 50% between 1983 and 1995. A 2012 e-mail survey of 50,347 respondents revealed that 33.2% of dogs were 6 to 10 years of age and 14.7% were older than 11 years in the United States. The average life expectancy of dogs raised in the home is affected by health care, aging and nutrition.And, the aging process is influenced by breed size, genetics, nutrition, environment, and other factors. Although many pets remain active and youthful well into their teens, most dogs start to slow down and may show signs of aging beginning as early as 5 or 6 years of age. Improvements in the control of various diseases and in the nutrition of dogs have resulted in a gradual increase in the average lifespan of companion dogs. Nutritional goals for aging dogs include supporting health and vitality, preventing the onset or slowing the progression of age-related health disorders, and enhancing the dog's quality of life and, if possible, life expectancy. Aging brings with its physiologicchanges. Some changes are obvious, such as whitening of hair, a general decline in body and coat condition, and failing senses including sight and hearing. Other changes are less obvious, however, and these include alterations in the physiology of the digestive tract, immune system, kidneys, and other organs. Nutritional requirements can change with age. In addition, many diseases common in older dogs may be nutrient-sensitive, meaning that diet can play an important role in the management of the condition.

• Journal of the Korean Society of Radiology
• /
• v.13 no.3
• /
• pp.339-348
• /
• 2019

The purpose of this study was to investigate the effect of carotid artery ultrasound Respectively. The carotid intima-media thickness is known to have a significant correlation with cardiovascular disease and cerebrovascular disease. We investigated the relationship between carotid intima - media thickness, body mass index, waist circumference, the blood lipid value, fasting blood glucose, glycated hemoglobin, and blood pressure using carotid artery ultrasound. The carotid artery ultrasound was considered to be abnormality of IMT thickness over 0.8 mm and the presence or absence of atherosclerotic plaque was evaluated. Serological tests were used to compare the geologic value, fasting blood glucose level, and glycated hemoglobin. As a result, waist circumference (=.022), low density cholesterol (=.004), fasting blood glucose level (.019), and glycemic index (.002) were analyzed as predictors of atherosclerosis. In the ROC curve analysis, sensitivity was 87.80% (95% CI: 73.8-95.9), specificity was 41.67% (95% CI: 30.2-53.9), sensitivity was 78.05% (95% CI: 62.4-89.4) in low density lipoprotein, Specificity was 50.00% (95% CI: 38.0-62.0), sensitivity was 73.11% (95% CI: 57.1-85.8), specificity was 61.11 (95% CI: 48.9-72.4) and sensitivity was 82.93%-91.8) and a specificity of 43.06% (31.4-55.3). In logistic regression analysis, the risk of atherosclerosis was 0.248 times at waist circumference (WC)> 76 cm, 3.475 times at low-density lipoprotein (LDL-C) ${\geq}124mg/dL$, 0.618 at HbA1c> 5.4% It appeared as a times. We suggest that prospective study of carotid artery ultrasound should be performed for the effective prevention of cardiovascular diseases.

• Journal of the Korean Society of Radiology
• /
• v.13 no.4
• /
• pp.495-502
• /
• 2019

A typical cerebrovascular disease among cerebrovascular diseases is vascular diseases such as cerebral infarction, cerebral hemorrhage, cerebral aneurysm, cerebrovascular stenosis. If the disease occurs and causes cerebral damage, it may be difficult to recover completely. So that, Must continue to perform health care through examination early. In particular, Because most cerebrovascular disease examining use radiation equipment and Thus this study was to find out how to select about the optimal examining method and X-ray dose decrease method among different examining method though comparison and analysis for the entrance surface dose (ESD) on cerebrovascular examining with Trance Femoral Cerebral angiography (TFCA) and Cerebral Computed Tomographic Angiography (CCTA). Also, want to find out how to select about the optimal examining method for worried patient that contrast medium side effect though measuring and evaluating for contrast usage. Data were collected from 70 patients (43 males and 27 females) who underwent CCTA at Yeosoo region hospital from June 2018 to December 2018 and 61 patients (34 males and 27 females) who underwent TFCA at Pyeongtaek region hospital from June 2018 to November 2018. ESD analysis method collected retrospective data though M-view and PACS PLUS program, Used contrast usage measuring method did reality measuring method. In the analysis using SPSS, the ESD of TFCA was $245.74{\pm}71.91$, which was $32.05{\pm}7.74$ lower than the dose of $277.79{\pm}79.65$ of CCTA ESD, and statistically significant at t = 3.249, p = 0.017 (p<0.05). As a result of the comparison of the total amount of contrast agent, the mean contrast agent used in TFCA was $55.05{\pm}17.68ml$, which was about 14.95 smaller than the amount of contrast agent used in CCTA, and statistically significant t = -4.548, p<0.001. In conclusion, the ESD of TFCA was statistically significantly lower than that of CCTA, and also the used contrast usage was significantly tiny than that of CCTA. Therefore, Select the method to increase the utilization of TFCA for cerebral disease examining, we can consider X-ray dose decrease method at the same time as to decrease side effect of contrast medium.

• Journal of the Korean Society of Radiology
• /
• v.13 no.4
• /
• pp.503-508
• /
• 2019

In short a binary value according to a change in the tube voltage by using one of VOLUME AXIAL MODE of scanning techniques of chest CT image quality evaluation in order to obtain high image and to present the appropriate tube voltage. CT instruments were GE Revolution (GE Healthcare, Wisconsin USA) model and Phantom used Pediatric Whole Body Phantom PBU-70. The test method was examined in Volume Axial mode using the pediatric protocol used in the Y university hospital of mass-produced material. The tube voltage was set to 70kvp, 80kvp, 100kvp, and mAs was set to smart mA-ODM. The mean SNR difference of the heart was $-4.53{\pm}0.26$ at 70 kvp, $-3.34{\pm}0.18$ at 80 kvp, $-1.87{\pm}0.15$ at 100 kvp, and SNR at 70 kvp was about -2.66 higher than 100 kvp and statistically significant (p<0.05) In the Lung SNR mean difference analysis, $-78.20{\pm}4.16$ at 70 kvp, $-79.10{\pm}4.39$ at 80 kvp, $-77.43{\pm}4.72$ at 100 kvp, and SNR at 70 kvp at about -0.77 higher than 100 kvp were statistically significant. (p<0.05). Lung CNR mean difference was $73.67{\pm}3.95$ at 70 kvp, $75.76{\pm}4.25$ at 80 kvp, $75.57{\pm}4.62$ at 100 kvp and 20.9 CNR at 80 kvp higher than 70 kvp and statistically significant (p<0.05) At 100 kvp of tube voltage, the SNR was close to 1 while maintaining the quality of the heart image when 70 kvp and 80 kvp were compared. However, there is no difference in SNR between 70 kvp and 80 kvp, and 70 kvp can be used to reduce the radiation dose. On the other and, CNR showed an approximate value of 1 at 70 kvp. There is no difference between 80 kvp and 100 kvp. Therefore, 80 kvp can reduce the radiation dose by pediatric chest CT. In addition, it is possible to perform a scan with a short scan time of 0.3 seconds in the volume axial mode test, which is useful for pediatric patients who need to move or relax.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.20 no.9
• /
• pp.405-411
• /
• 2019

In this study, tensile tests were carried out on materials (A516-60, A283-C, A285-C, and SB410) for structural and pressure vessels at temperatures of $20^{\circ}C$, $-20^{\circ}C$, and $-40^{\circ}C$, and the changes in the mechanical properties were analyzed. Compared to the results at $20^{\circ}C$, the average yield stress increased by 6.4% and 7.5% at $-20^{\circ}C$ and $-40^{\circ}C$ for A516-60, while the average tensile stress increased by 1.3% and 4.1%, respectively. The average elongation decreased by 4.7% and 20.4% at these temperatures. In the case of A283-C, the average yield stress increased 8.8% and 9.8%, the average tensile stress increased by 4.1% and 5.9%, and the average elongation rate decreased by 7.4% and 9.9% at $-20^{\circ}C$ and $-40^{\circ}C$, respectively. For A285-C, the average yield stress increased by 1.8% and 8.6%, and the average tensile stress increased by 2.6% and 5.3%, respectively, but there was little change in the average elongation. Finally, for SB410, the average yield stress increased by 7.1% and 11.8%, the average tensile stress increased by 4.3% and 5.5%, but the average elongation rate decreased by 8.7% and 13.5%, respectively.