• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.32 no.6
• /
• pp.251-261
• /
• 2022

This paper describes the finite element analysis and die design change of spring retainer forging process to reduce the cold forging load and plastic forming stress concentration. Plastic deformation analysis was carried out in order to understand the forming process of workpieces and elastic stress analysis of the die set was performed in order to get basic data for the die fatigue life estimation. Cold forging die design was set up to each process with different four types analysis progressing, the upper and lower dies shapes with combination of fillets and chamfers shapes of cold forging dies. This study suggested optimal cold forging die geometry to reduce cold forging load. The design parameters of fillets and chamfers are selected geometry were selected to apply optimization with the DoE (design of experiment) and Taguchi method. DoE and Taguchi method was performed to optimize the workpiece preform shape for spring retainer forging process, it was possible to expect an increase in cold forging die life due to the 20 percentage forging load reduction.

• Journal of Advanced Marine Engineering and Technology
• /
• v.40 no.4
• /
• pp.314-319
• /
• 2016

Flange bolt has a circular flange under the head that acts like a washer to distribute the clamping load over a large area. Flange bolt has usually been manufactured by cold forging. Flower shape defect occurs in the flange forging stage. This defect causes lack of dimensional accuracy and low quality. So it is needed to improve these forging defects. In this study, die design method for flower shape defect of flange bolt was suggested. In order to improve flower shape defect, inner diameter of the addition die in conventional forging process was modified. The forging process with applied modified die was simulated by commercial FEM code DEFORM-3D. The simulated results for modified die were confirmed by experimental trials with the same condition.

• Journal of the Korean Society for Precision Engineering
• /
• v.17 no.1
• /
• pp.61-67
• /
• 2000

Gears are the most commonly used parts in automotive and industrial applications. One of most common modes of gear failures is tooth breakage, which is usually produced by the bending fatigue failure. It is important to manufacture the gears which can withstand the applied stresses in view of safety and economic requirement. This paper deals with bending fatigue strength for cold forged bevel gear. Especially, to compare fatigue characteristics for manufacturing processes difference, bending fatigue tests of bevel gears made by three different processes respectively. Results indicate that the fatigue strength of bevel gear is improved by cold forging process. Intergranular fracture is found on fatigue fracture surface, and dimples are observed on final fracture surface. The fatigue failure cannot be considered as a deterministic quantity, but must be characterized statistically. This study proposes a method to estimate bending fatigue lift of the bevel gear using the probability-load-life and Weibull analysis.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.17 no.7
• /
• pp.256-262
• /
• 2016

This study performed the back-pressure cold forging analysis to minimize the non-forming area of gear teeth for the output hub and reaction hub in automatic transmission. Two important factors of the back-pressure cold forging process, the load of the punch and the backup force applied to the sleeve, were determined through displacement control analysis. The non-forming area of the gear teeth was compared with both cases of the displacement control analysis and load control analysis, and their solution is similar to the measuring result of a real workpiece. The results show that the load of the punch is dependent on the reduction area of the workpiece, and the backup force applied to the sleeve is determined with regard to the cross-section-area of sleeve. This analysis procedure can be useful and effective in determining the manufacturing condition of the back-pressure cold forging process to minimize the non-forming area.

• Proceedings of the Materials Research Society of Korea Conference
• /
• 2012.05a
• /
• pp.106.2-106.2
• /
• 2012

Ti-Ni합금은 CsCl구조의 B2상, monoclinic 구조의 B19'(M)상과 rhombohedral 구조의 R상(R)이 나타난다고 알려져 있고, 이들 상의 변태에 의해 열탄성 마르텐사이트와 응력유기 마르텐사이트에 의한 형상기억효과와 초탄성 효과를 가지고 있다. 또한 Ti-Ni 합금은 우수한 형상기억특성을 가질 뿐만 아니라 생체적합성, 가공성 및 내식성 등이 뛰어나 공업분야 및 생체분야에서 폭 넓게 활용되고 있다. Ti-Ni합금의 형상기억특성은 냉간가공 후 어닐링 처리의 온도와 시간에 따른 matrix 내 Ni의 농도, 석출물의 밀도와 크기, 전위밀도와 전위주위의 응력장에 의해 영향을 받는다고 알려져 있다. 본 연구에서는 Ti-Ni합금의 형상기억 특성 및 변태온도에 미치는 영향을 조사하기 위해 다양한 냉간가공률의 시료를 제작하여 다양한 온도에서 Annealing 처리를 하여 냉간가공률 및 Annealing 온도가 형상기억특성에 미치는 영향을 조사하였다. Ti-50.4 at.% Ni 합금은 진공 아크 용해로에서 용해 하였으며, 용해된 Ingot는 열간단조 및 열간 압출한 후 냉간 인발과 중간온도에서 어닐링을 반복하면서 직경 0.5mm의 선재로 만들었다. 최종적으로 제작한 선재의 냉간가공률은 9.5%, 18.2%, 34.5%, 45% 이었다. 각 시편은 5X10-5torr의 진공으로 석영관에 진공 봉입하여 각각 673K, 723K, 783K에서 1hr 열처리 하였다. 합금의 형상기억특성과 변태온도는 DSC에 의해 조사되었다. DSC 측정 결과, 냉간가공률이 증가함에 따라 마르텐사이트 변태 온도는 감소하였고, 어닐링 온도가 증가함에 따라 마르텐사이트 변태 온도는 증가하였다. 또한 가공률이 증가하여도 R상 변태온도는 큰 변화가 없었고, Annealing온도가 증가함에 따라 R상 변태온도는 감소하였다. 또한, 형상기억특성은 인장시험기를 이용한 정하중 열싸이클 테스트를 이용하여 평가 하였다. 냉간 가공률이 증가함에 따라 안정한 형상기억특성을 나타내었다.

• Transactions of Materials Processing
• /
• v.15 no.7 s.88
• /
• pp.485-489
• /
• 2006

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.21 no.1
• /
• pp.49-55
• /
• 2022

Recently, the automobile industry has continued to demand lighter materials owing to international environmental regulations and increased convenience. To address this demand, aluminum parts have increased in popularity and are mainly developed and produced through hot forging and cold pressing. However, because this method has low yield and low production efficiency, a new manufacturing method is desirable. In this study, the water capacity efficiency of an aluminum inner tie rod socket was investigated using cold forging that provided a high yield and excellent production efficiency. Mechanical properties were derived through tensile testing of 6110A aluminum materials, and critical fracture factor and process analysis based on experimental data were carried out. The optimized process was applied as a prototype using cold multi-stage forging, and based on the derived results, the formability, productivity, and material efficiency of aluminum inner tie rod socket parts using this cold forging process was verified.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 1998.10a
• /
• pp.17-17
• /
• 1998

1970년대에 개발된 Ti-15-3 합금은 상온에서 우수한 성형성을 가지고 있어 Ti-6-4 합금보다 성형 공정을 대폭 감소시킬 수 있어 생산비용을 크게 감소시킬 수 있는 장점이 있는 합금이다. 또한, 냉간 성형성이 우수하고 강화 범위가 폭넓기 때문에 항공기의 프레임, 항공기 압력 용기 및 고장력 유압 튜브 등에 많이 사용하고 있으나, 열간 성형성이 Ti-6-4 티타늄 합금보다 좋지 않기 때문에 이제까지의 적용 분야는 판재 성형 등의 한정된 분야에만 적용되어 오고 있는 실정이다.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.18 no.6
• /
• pp.395-399
• /
• 2017

The LPI fuel filter housings used in automobiles were made from conventional die castings but have recently been developed by cold forging to improve the weight and durability. On the other hand, a sink may develop at the core of the forged product due to the resulting T-shape, which not only reduces the aesthetics, but also increases the post-processing cost of the product. Therefore, this research focused on methods to predict and mitigate sink development and progression during the T-shape forging process. Finite element analysis of the forging process was first performed to determine the optimal initial workpiece devoid of burrs and underfills. An accurate sink prediction was then obtained via metal flow analysis, which was a result of the finite element simulation. Through finite element analysis, it was confirmed that sink development is a product of the differences in nodal velocities arising from the T-shaped forging process. Consequently, a pad was inserted beneath the sink to minimize these velocity differences. The results yielded significant improvement with regard to the sink defect. This method was practically applied to an industrial site to validate the sink improvement.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.5 no.3
• /
• pp.170-177
• /
• 1981

1,200.deg.C에서의 단조철은 점소성을 나타내며 인발과 압출시 변형영역이 구형수렴형태가 됨을 실험을 통하여 나타난다. 이 변형역 모델로부터 평형방정식을 사용하여 평균 압출 및 인발응력과 정수압을 계산해 낸다. 평균 압출 및 임발응력은 상계 해석 방법에 의한 결과와 비교하여 본 연구의 해석방법의 유효성을 타진하고 정수압은 다른 연구자들의 결과와 비교 검토되며 특히 냉간가공의 경우와 비교 검토 된다. 그 외에 마찰계수, 급형각도와 단면감소율의 영향에 대해서도 논의 된다.