Proceedings of the Korean Vacuum Society Conference
/
2016.02a
/
pp.119.1-119.1
/
2016
크라이오 워터펌프(CWP)는 크라이오 펌프(CP)와 달리 10 K 활성탄 어레이는 장착하지 않고 100 K 정도로 냉각시킨 배플만을 사용하여 물의 배기속도를 최적화 하는 데 초점을 맞춘 진공펌프다. 용기 압력이 10-9 mbar 대가 될 때까지는 잔류기체의 90% 이상이 수분이므로 다른 기체들의 배기 보다는 물을 잘 배기하는 것이 배기시간을 단축하고 도달 진공도를 낮추는 첩경이라는 아이디어에 근거를 두고 있다. CWP는 물 흡착확률을 거의 1에 가깝게 만들어서 오리피스 컨덕턴스에 육박하는 이상적인 펌프를 제작할 수 있지만 용도상 직부형(close type), 통과형(in-line type) 및 내장형(in-vessel type) 등 세 가지 다른 형태에 따라 성능도 약간씩 다르다. CWP는 모든 기체에 반응하는 정통적인 CP에 비해 훨씬 간단하고 저렴하게 만들 수 있으면서도 진공 시스템에 큰 영향을 미칠 수 있지만 물 이외의 기체들을 배기할 펌프가 필요하다는 측면에서 활용에 제약이 있다. 만일 TMP를 이미 사용하고 있거나 작은 TMP를 추가로 달아서 충분히 작동이 가능한 시스템이면서 수분 발생이 많은 곳이나, 또 활성탄의 오염이나 산소 분위기 등 CP 투입이 꺼려지는 환경이라면 CWP 사용이 좋은 선택이 될 수 있다. CWP의 물 배기용량은 CP의 알곤이나 질소 배기용량에 준하는 크기로 0.5g/cm2 이상임이 실험적으로 입증되었다. 따라서 일반적인 상황에서 정상 작동시 대부분의 기체는 TMP로 배출하고 잔류 수분만 포집하므로 CP처럼 주기적인 재생이 필요 없다. 필요하다면 CWP는 금속 표면에 응축된 물을 드라이펌프 작동만으로 쉽게 제거할 수 있고 혹시 오염 물질이 붙어도 세척이 용이하다. 이런 사용상 융통성과 여러 가지 장점에도 불구하고 그동안 물배기에 대한 인식이 미흡하고, 또 부수적이고 추가적인 비용이 드는 것으로 생각되어 주목을 받지 못했지만 디스플레이와 반도체 산업을 필두로 물 분압을 낮추고 생산수율을 높이는 것에 점점 더 관심이 높아지면서 CWP에 대한 수요도 높아지고 있다. 본 보고에서는 20인치 통과형 CWP를 만들고 14인치 TMP에 얹어 복합 진공배기시스템을 구성한 후 물 배기속도와 알곤, 질소 및 수소 배기속도를 측정하고 예측치와 비교했다. 아울러 물 배기용량 측정 및 CWP의 온도제어와 펌프재생 특성 평가 결과도 정리했다.
Effects of native and RS-3 type resistant starches prepared from autoclaved-cooled amylomaize VII(AVII) and normal maize starches(NMS) on the rheological and baking properties of wheat flour dough and quality of breads were investigated. In farinogram, water absorption and dough development time were increased, but stability was reduced by the addition of RS. The addition of native starches or resistant starch made from AVII to wheat flour improved the total volume and specific loaf volume of bread compared with the control(no addition), but the addition of NMS-RS reduced those. During the storage of bread at room temperature, the moisture content of control was decreased but those of native starch- or RS-added breads remained constantly. AVII-RS- or NMS-RS-added bread was evaluated to have good overall acceptability compared with control by elementary school students. The addition of enzyme-resistant starch to bread regardless of botanical sources of starch not only improved the overall acceptability and nutritional benefits but also improved the sensory acceptability.
Oh, Seung Eun;Lee, Sun Kyu;Choi, Joong Kyu;Song, Kook Hyun;Baek, Jong Sik
Korean Journal of Optics and Photonics
/
v.23
no.4
/
pp.154-158
/
2012
In this paper, for low cost infrared optical equipment, we design and fabricate an infrared optical system for an uncooled detector using PGM(Precision Glass Molding) lenses. The designed infrared optical system has a good athermalization, and the material of all of its lenses is a chalcogenide glass suitable for the PGM method. In addition, we also fabricate the same infrared optical system using SPDT(Single Point Diamond Turning) lenses in order to measure the optical performance of PGM lenses. We measure the MTF(Modulation Transfer Function) of the two infrared optical systems which use the PGM lenses and the SPDT lenses. And then we compare and analyze the images of them both. As a result, we find that they have only a very small difference in optical performance. If the use of PGM lenses increases, we expect to reduce the cost of infrared optical equipment.
This study was conducted to investigate effects of cooling methods on the growth and yield of tomato cv. momotaro in the glasshouse for four years from 1996 to 1999. Cooling methods were fan, fan and fogging, fan and shading(temp. control), fan and shading(radiation control), fan and shading (temp. control) with fogging. Fan, Fogging and Shading(temp. control) were operated automatically when air temperature was over 3$0^{\circ}C$. Amount of fogging was 500m1/min/100m$^2$and Droplets in a fog were 50 microns or smaller. Shading(radiation control) was operated automatically when solar radiation was over 500W/m$^2$. The growth and yield were the least in fan and shading(temp. control) method due to lack of light Intensity. Fogging method must be reconsidered for expensive equipment and maintenance expenses. As the matter stands, It is suggested to be the most considerable cooling method to increase ventilation rate with fan or use fan and shading(radiation control).
In this study, a device and pressure press process that is able to substitute autoclave process is developed. This process complements disadvantages of autoclave process which are long process-time and high production cost. The developed device provides air pressure as well as the vacuum which are greatest feature of autoclave process. The device is sealed using hydraulic pressure to keep the air pressure inside the mold. The transfer of the heat is designed to be direct. The heating and pressure charging time are decreased by reducing the interior space. Tooling cost is reduced dramatically compared to autoclave process. Spring-back phenomenon is measured and compared. The temperatures of several parts of the mold during molding are measured. The fiber volume fraction of the parts molded by autoclave process and by the developed process are compared.
Proceedings of the Korean Institute of Surface Engineering Conference
/
2017.05a
/
pp.136-136
/
2017
화학제염 기술은 산화제, 환원제, 금속이온, 무기산등이 혼합되어 있는 화학용액을 사용하여 원전기기 계통 내부에 생성된 고방사능 준위의 산화막과 오염물질을 제거하는 기술이다. 원전의 해체 및 유지보수에 있어 방사능 피복저감을 위한 필수적인 기술이다. 현재 원전 해체 산업은 잠재성이 높은 고부가가치 창출 산업으로 주목을 받고 있다. 원전 보유국의 경우, 기존 상용 제염기술과는 차별성 있는 제염기술을 확보하고자 노력하고 있다. 기존의 공정과 비교하여 공정비용 및 시간을 감소시킬 수 있어야 할 뿐만 아니라, 화학용액에 의한 원전 계통 금속 부품의 부식 및 손상을 최소화해야 한다. 금속 부품이 화학약품에 의한 부식손상을 받는다면 금속 부품의 수명 및 재활용 가치가 감소하기 때문에, 화학제염 기술 적용에 있어 용액에 대한 재료의 건전성 평가가 사전에 필히 이루어져야 한다. 본 연구에서는 원전 냉각재 펌프용 재료로 주로 사용되는 Stainless 304강을 시험편으로 선정하여, 화학제염 시험공정 3가지에 대한 부식손상 특성을 규명하였다. 산화공정은 과망간산($HMnO_4$) 용액을 공통으로 사용하였으며, 산화공정 종료 후 환원공정은 각 시험공정에 따라 시험공정 1은 옥살산($H_2C_2O_4$) 2000ppm, 시험공정 2는 옥살산($H_2C_2O_4$)1500ppm + 시트르산($H_8C_6O_7$)500ppm, 그리고 시험공정 3은 옥살산($H_2C_2O_4$) 3000ppm 용액을 각각 투입하여 수행하였다. 산화, 환원공정을 1Cycle로 하여, 각 시험공정 별로 총 5Cycle을 실시하였다. 각 시험공정 Cycle종료 후 시험편을 취외하여 무게감량측정, SEM(Scanning electron microscope) 분석, 3D현미경분석 그리고 타펠분극 실험을 실시하였다. 각 분석결과를 토대로 하여, Stainless 304강에 대한 화학제염 시 모델별 시험공정에 따른 부식특성을 규명하였다.
With increase of concern about the Ubiquitous application, the necessity of the computer system which is miniaturized is becoming larger. The ARM processor is showing a high share from embedded system market. In this paper, ideal method for RTD-1000 controller construction and development is described using ARM microcontroller. Existing RTD-1000 measures distance of disconnection or defect of sensing casket by measuring receiving reflected wave which was sent via copper wire inside the leaking sensing rod. Using this RTD-1000, leakage and breakage of water and oil pipe can be sensed and it reports damage results to the networks. But, existing RTD-1000 wastes hardware resources much and costs a great deal to installation. Also, it needs a cooling device because the heating problem, and has some problem of the secondary memory unit such as the hard disk. So, long tenn maintenance has some problems in the outside install place. In this paper, for the resolving the problem of RTD-1000, RTD-1000A embedded system based on ARM is proposed and simulated.
Transactions of the Korean Society of Mechanical Engineers A
/
v.35
no.10
/
pp.1315-1321
/
2011
Prior to the experimental and production stages of goods, the strengths should be evaluated in the design stage. The introduction of commercial codes at the design stage gives benefits such as cost and time economies in the production and strength evaluation. In this study, structural analysis and fatigue analysis are carried out using ANSYS modeling of the 3D geometry of the wheel. In a comparison of dish-type and spoke-type wheels, it is shown that the deformation and maximum equivalent stress for the dish-type wheels are lower than those for spoke-type wheels. Nevertheless, spoke-type wheels are often used because they are light and have exhibit excellent cooling performance. Furthermore, according to the results of life analysis, aluminum wheels show improved resistance to fatigue compared to steel wheels.
Proceedings of the Korean Vacuum Society Conference
/
2011.08a
/
pp.130-131
/
2011
박막의 제조는 많은 연구의 가장 기초가 되는 시편을 만드는 과정으로 현대의 과학기술에서 매우 중요한 공정 중의 하나이다. 그러나 이러한 박막의 제조는 제조하는 사람의 숙련도나 장치에 의존하며 경우에 따라서는 원하는 특성의 박막을 제조하는 것이 매우 어려운 작업이 되기도 한다. 따라서 경험이 없는 연구자의 경우는 때때로 까다로움과 번거로움을 느끼게 되며, 안정된 공정을 찾기까지 많은 시간을 소비 하게 된다. 특히 부적절한 증발방법의 선정에 따른 실험 결과는 경제적인 손실을 초래할 뿐만 아니라 실험하는 사람을 좌절시키는 가장 큰 요인이 되어왔다. 진공증착에 의한 박막의 제조는 증발법과 스퍼터링, 이온플레이팅 등의 방법이 있으며 이중 증발을 이용한 박막의 제조에는 저항가열 증발, 전자빔 가열 증발, 유도가열 증발 등의 방법으로 구분하고 있다. 저항가열 증발원은 가격이 저렴하다는 장점은 있으나 증발원이 손쉽게 파손되거나 증발량이 일정하지 않아 박막의 정밀 제어가 어려울 뿐만 아니라 때에 따라서는 1 ${\mu}m$ 이상의 후막 형성에도 어려움이 있는 등 많은 제약이 있다. 따라서 적절한 증발원의 선정이 실험의 효율성을 좌우하는 경우가 많다. 적절한 증발원의 선정과 효율적인 실험을 위해 증발원 제조회사에서는 증발원의 선정과 증발 조건과 관련된 자료를 카탈로그 형태로 발행하고 있다. 그러나 그러한 자료만으로는 객관적인 정보를 얻기에 충분하지 못한 경우가 많으며, 어떤 경우에는 저자 등의 경험과 일치하지 않는 정보도 포함하고 있었다. 전자빔 증발원은 냉각이 되는 Crucible에 물질을 담고 고전압의 전자빔으로 물질을 가열시켜 증발시키는 증발원으로 1960년대 이후 박막 제조 실험에 이용되기 시작하였다. 전자빔은 고순도의 피막 제조가 가능하고 증발물질의 교체가 쉬우며 고속 증발이 가능함은 물론 다층막의 제조가 용이하고 증발물질의 제조비용이 저렴하다는 장점이 있다. 이러한 장점 때문에 1970년대 이후에는 전자빔을 이용한 박막제조가 폭 넓게 이루어졌고 이때를 즈음하여 전자빔을 이용한 물질의 증발 특성이 논문으로 발표되기도 하였다. 본 연구에서는 증발에 관한 저자들의 경험을 바탕으로 저항가열과 전자빔을 이용하여 증발실험을 진행한 물질계를 중심으로 각 물질의 증발특성과 가장 효율적인 Liner 등에 대해 기술하였다. 특히, 각종 물질의 증발 특성을 체계화함은 물론 효율적인 증발 방법을 객관적인 Data와 함께 제공하여 효과적인 박막 제조 실험에 도움이 되고자 하였다.
$CO_2$ extinguishing system is the most $\phi$pular among the gas extinguishing system. $CO_2$ is usually stored with liquified state. But, it gasifies at the tip of nozzle when $CO_2$ was released through the pipe and head. A ro$\alpha$n temperature is very low when $CO_2$ was released. So electrical instrument, magnetic storage equipment and memory semiconductor are electrically or physically injured by cooling effect in a few minutes. So, we intend to find out temperature profile and electrical damage in compartment area, and supply basic d data for research and making standards and code through the full scale experiment. As result of experiment on the damage due to cooling effect from $CO_2$ extinguishing system, i instantaneous discharging temperature. was $-82.5^{\circ}C$ in average. An average temp. in the compartment after discharging $CO_2$ was $-40^{\circ}C$.
본 웹사이트에 게시된 이메일 주소가 전자우편 수집 프로그램이나
그 밖의 기술적 장치를 이용하여 무단으로 수집되는 것을 거부하며,
이를 위반시 정보통신망법에 의해 형사 처벌됨을 유념하시기 바랍니다.
[게시일 2004년 10월 1일]
이용약관
제 1 장 총칙
제 1 조 (목적)
이 이용약관은 KoreaScience 홈페이지(이하 “당 사이트”)에서 제공하는 인터넷 서비스(이하 '서비스')의 가입조건 및 이용에 관한 제반 사항과 기타 필요한 사항을 구체적으로 규정함을 목적으로 합니다.
제 2 조 (용어의 정의)
① "이용자"라 함은 당 사이트에 접속하여 이 약관에 따라 당 사이트가 제공하는 서비스를 받는 회원 및 비회원을
말합니다.
② "회원"이라 함은 서비스를 이용하기 위하여 당 사이트에 개인정보를 제공하여 아이디(ID)와 비밀번호를 부여
받은 자를 말합니다.
③ "회원 아이디(ID)"라 함은 회원의 식별 및 서비스 이용을 위하여 자신이 선정한 문자 및 숫자의 조합을
말합니다.
④ "비밀번호(패스워드)"라 함은 회원이 자신의 비밀보호를 위하여 선정한 문자 및 숫자의 조합을 말합니다.
제 3 조 (이용약관의 효력 및 변경)
① 이 약관은 당 사이트에 게시하거나 기타의 방법으로 회원에게 공지함으로써 효력이 발생합니다.
② 당 사이트는 이 약관을 개정할 경우에 적용일자 및 개정사유를 명시하여 현행 약관과 함께 당 사이트의
초기화면에 그 적용일자 7일 이전부터 적용일자 전일까지 공지합니다. 다만, 회원에게 불리하게 약관내용을
변경하는 경우에는 최소한 30일 이상의 사전 유예기간을 두고 공지합니다. 이 경우 당 사이트는 개정 전
내용과 개정 후 내용을 명확하게 비교하여 이용자가 알기 쉽도록 표시합니다.
제 4 조(약관 외 준칙)
① 이 약관은 당 사이트가 제공하는 서비스에 관한 이용안내와 함께 적용됩니다.
② 이 약관에 명시되지 아니한 사항은 관계법령의 규정이 적용됩니다.
제 2 장 이용계약의 체결
제 5 조 (이용계약의 성립 등)
① 이용계약은 이용고객이 당 사이트가 정한 약관에 「동의합니다」를 선택하고, 당 사이트가 정한
온라인신청양식을 작성하여 서비스 이용을 신청한 후, 당 사이트가 이를 승낙함으로써 성립합니다.
② 제1항의 승낙은 당 사이트가 제공하는 과학기술정보검색, 맞춤정보, 서지정보 등 다른 서비스의 이용승낙을
포함합니다.
제 6 조 (회원가입)
서비스를 이용하고자 하는 고객은 당 사이트에서 정한 회원가입양식에 개인정보를 기재하여 가입을 하여야 합니다.
제 7 조 (개인정보의 보호 및 사용)
당 사이트는 관계법령이 정하는 바에 따라 회원 등록정보를 포함한 회원의 개인정보를 보호하기 위해 노력합니다. 회원 개인정보의 보호 및 사용에 대해서는 관련법령 및 당 사이트의 개인정보 보호정책이 적용됩니다.
제 8 조 (이용 신청의 승낙과 제한)
① 당 사이트는 제6조의 규정에 의한 이용신청고객에 대하여 서비스 이용을 승낙합니다.
② 당 사이트는 아래사항에 해당하는 경우에 대해서 승낙하지 아니 합니다.
- 이용계약 신청서의 내용을 허위로 기재한 경우
- 기타 규정한 제반사항을 위반하며 신청하는 경우
제 9 조 (회원 ID 부여 및 변경 등)
① 당 사이트는 이용고객에 대하여 약관에 정하는 바에 따라 자신이 선정한 회원 ID를 부여합니다.
② 회원 ID는 원칙적으로 변경이 불가하며 부득이한 사유로 인하여 변경 하고자 하는 경우에는 해당 ID를
해지하고 재가입해야 합니다.
③ 기타 회원 개인정보 관리 및 변경 등에 관한 사항은 서비스별 안내에 정하는 바에 의합니다.
제 3 장 계약 당사자의 의무
제 10 조 (KISTI의 의무)
① 당 사이트는 이용고객이 희망한 서비스 제공 개시일에 특별한 사정이 없는 한 서비스를 이용할 수 있도록
하여야 합니다.
② 당 사이트는 개인정보 보호를 위해 보안시스템을 구축하며 개인정보 보호정책을 공시하고 준수합니다.
③ 당 사이트는 회원으로부터 제기되는 의견이나 불만이 정당하다고 객관적으로 인정될 경우에는 적절한 절차를
거쳐 즉시 처리하여야 합니다. 다만, 즉시 처리가 곤란한 경우는 회원에게 그 사유와 처리일정을 통보하여야
합니다.
제 11 조 (회원의 의무)
① 이용자는 회원가입 신청 또는 회원정보 변경 시 실명으로 모든 사항을 사실에 근거하여 작성하여야 하며,
허위 또는 타인의 정보를 등록할 경우 일체의 권리를 주장할 수 없습니다.
② 당 사이트가 관계법령 및 개인정보 보호정책에 의거하여 그 책임을 지는 경우를 제외하고 회원에게 부여된
ID의 비밀번호 관리소홀, 부정사용에 의하여 발생하는 모든 결과에 대한 책임은 회원에게 있습니다.
③ 회원은 당 사이트 및 제 3자의 지적 재산권을 침해해서는 안 됩니다.
제 4 장 서비스의 이용
제 12 조 (서비스 이용 시간)
① 서비스 이용은 당 사이트의 업무상 또는 기술상 특별한 지장이 없는 한 연중무휴, 1일 24시간 운영을
원칙으로 합니다. 단, 당 사이트는 시스템 정기점검, 증설 및 교체를 위해 당 사이트가 정한 날이나 시간에
서비스를 일시 중단할 수 있으며, 예정되어 있는 작업으로 인한 서비스 일시중단은 당 사이트 홈페이지를
통해 사전에 공지합니다.
② 당 사이트는 서비스를 특정범위로 분할하여 각 범위별로 이용가능시간을 별도로 지정할 수 있습니다. 다만
이 경우 그 내용을 공지합니다.
제 13 조 (홈페이지 저작권)
① NDSL에서 제공하는 모든 저작물의 저작권은 원저작자에게 있으며, KISTI는 복제/배포/전송권을 확보하고
있습니다.
② NDSL에서 제공하는 콘텐츠를 상업적 및 기타 영리목적으로 복제/배포/전송할 경우 사전에 KISTI의 허락을
받아야 합니다.
③ NDSL에서 제공하는 콘텐츠를 보도, 비평, 교육, 연구 등을 위하여 정당한 범위 안에서 공정한 관행에
합치되게 인용할 수 있습니다.
④ NDSL에서 제공하는 콘텐츠를 무단 복제, 전송, 배포 기타 저작권법에 위반되는 방법으로 이용할 경우
저작권법 제136조에 따라 5년 이하의 징역 또는 5천만 원 이하의 벌금에 처해질 수 있습니다.
제 14 조 (유료서비스)
① 당 사이트 및 협력기관이 정한 유료서비스(원문복사 등)는 별도로 정해진 바에 따르며, 변경사항은 시행 전에
당 사이트 홈페이지를 통하여 회원에게 공지합니다.
② 유료서비스를 이용하려는 회원은 정해진 요금체계에 따라 요금을 납부해야 합니다.
제 5 장 계약 해지 및 이용 제한
제 15 조 (계약 해지)
회원이 이용계약을 해지하고자 하는 때에는 [가입해지] 메뉴를 이용해 직접 해지해야 합니다.
제 16 조 (서비스 이용제한)
① 당 사이트는 회원이 서비스 이용내용에 있어서 본 약관 제 11조 내용을 위반하거나, 다음 각 호에 해당하는
경우 서비스 이용을 제한할 수 있습니다.
- 2년 이상 서비스를 이용한 적이 없는 경우
- 기타 정상적인 서비스 운영에 방해가 될 경우
② 상기 이용제한 규정에 따라 서비스를 이용하는 회원에게 서비스 이용에 대하여 별도 공지 없이 서비스 이용의
일시정지, 이용계약 해지 할 수 있습니다.
제 17 조 (전자우편주소 수집 금지)
회원은 전자우편주소 추출기 등을 이용하여 전자우편주소를 수집 또는 제3자에게 제공할 수 없습니다.
제 6 장 손해배상 및 기타사항
제 18 조 (손해배상)
당 사이트는 무료로 제공되는 서비스와 관련하여 회원에게 어떠한 손해가 발생하더라도 당 사이트가 고의 또는 과실로 인한 손해발생을 제외하고는 이에 대하여 책임을 부담하지 아니합니다.
제 19 조 (관할 법원)
서비스 이용으로 발생한 분쟁에 대해 소송이 제기되는 경우 민사 소송법상의 관할 법원에 제기합니다.
[부 칙]
1. (시행일) 이 약관은 2016년 9월 5일부터 적용되며, 종전 약관은 본 약관으로 대체되며, 개정된 약관의 적용일 이전 가입자도 개정된 약관의 적용을 받습니다.