• Korean Journal of Poultry Science
• /
• v.41 no.3
• /
• pp.159-164
• /
• 2014

This study was conducted to investigate whether water chilling had effect on water retention, freshness or internal temperature of chicken carcasses during chilling or storage in two different chicken processing plants (designated as A and B). A total of 240 carcasses from chicken processing plants (n = 120 per chicken processing plant) was randomly sampled and evaluated the effect of water chilling on carcass characteristics (i.e., water retention, water loss or freshness during chilling or storage). Torrymeter value was used as an indicator of freshness in chicken carcasses. Water chilling did not affect carcass water retention between the processing plants. However, chicken carcasses processing in B plant exhibited significantly higher freshness (p<0.05) compared with those in A plant. This difference in freshness was mainly due to the longer transit time through the water chiller in A versus B plants. Water loss of carcasses during storage was not different between plants. It was found that carcass freshness can be affected by water chilling time as manifested in this study. Further study is warranted to see whether freshness or microbiological status of chicken carcasses may be affected depending on the chilling methods, i.e., air or water chilling.

• Journal of the Korean Geotechnical Society
• /
• v.38 no.12
• /
• pp.125-134
• /
• 2022

The Global Expansion Roadmap published by the International Space Exploration Coordination Group, which is organized by space agencies around the world, presents future lunar exploration guidance and stresses a lunar habitat program to utilize lunar resources. The Moon attracts attention as an outpost for deep space exploration. Simulating lunar surface environments is required to evaluate the performances of various equipment for future lunar surface missions. In this paper, an experimental study was conducted to simulate high vacuum pressure and cryogenic temperature of the permanent shadow regions in the lunar south pole, which is a promising candidate for landing and outpost construction. The establishment of an efficient dirty thermal vacuum chamber (DTVC) operation process has never been presented. One-dimensional ground cooling tests were conducted with various vacuum pressures with the Korean Lunar Simulant type-1 (KLS-1) in DTVC. The most advantageous vacuum pressure was found to be 30-80 mbar, considering the cooling efficiency and equipment stability. However, peripheral cooling is also required to simulate a cryogenic for not sublimating ice in a high vacuum pressure. In this study, an efficient peripheral cooling operation process was proposed by applying the frost ratio concept.

• Journal of the Korean Institute of Landscape Architecture
• /
• v.42 no.6
• /
• pp.21-30
• /
• 2014

The purpose of this study was to evaluate human thermal comfort in summer by the type of greenery in parks and to explore planning solutions to supply a comfortable thermal environment in parks. The research was conducted in three different land cover types: a park with multi-wide-canopied trees(WOODLAND), park with grass(LAWN) and park with pavement(PAV) as reference sites in Hamyang-Gun SangrimPark. Field measurements of air temperature, relative humidity and wind velocity, short-wave and long-wave radiation from six directions(east, west, north, south, upward and downward) were carried out in the summer of 2014(August 21-23 and 29-30). Mean Radiant Temperature($T_{mrt}$) absorbed by a human-biometeorological reference person was estimated from integral radiation and the calculation of angular factors. The thermal comfort index PET was calculated by Rayman software, UTCI, OUT_SET$^*$ were calculated using the UTCI Calculator and the Thermal Comfort Calculator of Richard DeDear. The results showed that the WOODLAND has the maximum cooling effect during daytime, reduced air temperatures/$T_{mrt}$ by up to $5.9^{\circ}C/35^{\circ}C$ compared to PAV and lowered heat stress values despite increasing relative humidity values and decreasing wind velocity. While the LAWN had very slight cooling effects during daytime, reduced air temperatures/$T_{mrt}$ by up to $0.9^{\circ}C/3^{\circ}C$ compared to PAV, the improvement effects of the thermal comfort index was very slight. However, during nighttime the microclimatic and radiant conditions of WOODLAND, LAWN, and PAV were similar owing to the absence of solar radiation, reduction of wind velocity and an increase in relative humidity. Because the shading and evapotranspiration effects of the WOODLAND were much greater than the evapotranspiration effects of the LAWN, it can be said that the solutions for supplying comfortable thermal environment in parks are to amplify the green volumes rather than green areas. This study was undertaken to evaluate the human thermal comfort in summer of WOODLAND/LAWN parks and to determine the improvement effects of thermal comfort index. These results can contribute to the provision better thermal comfort for park users during park planning.

• Journal of the Korean Chemical Society
• /
• v.42 no.6
• /
• pp.652-656
• /
• 1998

$(Ba_{0.8-x}Sr_{0.2})Y_xTiO_3\;(BSYT)$ powders were prepared by the calcination of metal-oxalate precipitates, which were obtained by wet chemical method using Ba, Sr, Y and Ti-nitrates and oxalic acid. Yttrium content, sintering temperature and cooling rate were taken as experimental factors. Response surface method was applied to modelling of the room temperature resistivity of BSYT. The results indicated that the Yttrium content had larger effect on the room temperature resistivity and minimum room temperature resistivity was at Yttrium content of 0.24 mol%. The validity of a modelling equation was confirmed by comparing the measured room temperature resistivity with the calculated one.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.35 no.12
• /
• pp.1285-1292
• /
• 2011

The characteristics of a semiconductor chiller system with EEV have been experimentally studied. Three experiments on temperature changes (increase and decrease), load variation, and control precision were conducted to investigate the operating characteristics of the semiconductor chiller. The power consumption was 8.9 kW during increase in temperature. The required time was 37.5 min for CH1 and 39.5 min for CH2. Moreover, the time required for falling temperature was 26.5 min. The control precision for partial load operation was relatively low compared to that of a full load operation. In addition, the CH2 equipped with a step motor showed better control precision. The power consumed by the chiller for process cooling water was 1.8 kW, which was one-half of that consumed during the refrigeration cycle. The objective of this study is to provide an optimal control guideline for the semiconductor chiller design.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.7 no.3
• /
• pp.384-392
• /
• 1997

Potassium lithium niobate(KLN) single crystal for a nonlinear-optic material, which changes the wavelength of lasers, has a ferroelectric tetragonal tungsten bronze structure at room temperature. It has been very hard to get single crystals of good quality due to the cracks during cooling process. In order to investigate the composition change due to the evaporation of solution during the growth, the thermogravimetric analysis was carried out. In atmospheric condition at $1000^{\circ}C$ which is about $10^{\circ}C$ higher than the crystal growing temperature, the weight change was negligible amount of $1.46{\times}10^{-5}$g/($\textrm{cm}^2$hr). By using both the Pt plate as the nucleation site and the slow cooling method with temperature fluctuation, KLN single crystal of good quality of size 1 cm could be obtained. The phase transition temperature was $490^{\circ}C$, which was higher than that reported by other researchers of the other composition. The optical anisotropy due to the absorption of OH-band exists in the range of IR.

• Composites Research
• /
• v.27 no.6
• /
• pp.254-259
• /
• 2014

In this study, a device and pressure press process that is able to substitute autoclave process is developed. This process complements disadvantages of autoclave process which are long process-time and high production cost. The developed device provides air pressure as well as the vacuum which are greatest feature of autoclave process. The device is sealed using hydraulic pressure to keep the air pressure inside the mold. The transfer of the heat is designed to be direct. The heating and pressure charging time are decreased by reducing the interior space. Tooling cost is reduced dramatically compared to autoclave process. Spring-back phenomenon is measured and compared. The temperatures of several parts of the mold during molding are measured. The fiber volume fraction of the parts molded by autoclave process and by the developed process are compared.

• Korean Journal of Optics and Photonics
• /
• v.22 no.2
• /
• pp.96-101
• /
• 2011

Operational and thermal characteristics of a thin disk Yb:YAG crystal with a thickness of 0.8 mm were studied using as a pumping source a fiber-coupled 930 nm laser diode. The heat generated in the crystal was dissipated by placing both surfaces in contact with copper plates with central hole, and the dependence of the temperature change in the illuminated spot on hole size was investigated by measuring the spectral change of the lasing peaks. The slope efficiency and optical-to-optical efficiency with respect to the LD pump power were as high as 42.2% and 34.8%, respectively. The temperature at the illuminated spot increased with diode current and with increasing hole size of the copper plate. When the hole size considerably exceeded the crystal thickness, the temperature rise deviated from the linear increase at high pump power.

• The Bulletin of The Korean Astronomical Society
• /
• v.37 no.2
• /
• pp.151.2-151.2
• /
• 2012

터보펌프 구동에 사용된 가스발생기 생성가스를 연소기로 공급하여 주추력 발생에 사용하는 다단연소 사이클 로켓엔진은 고추력을 요하는 우주 발사체에 널리 사용되고 있다. 다단연소 사이클 로켓엔진에 사용되는 가스발생기를 예연소기라 부르며 케로신과 액체산소를 추진제로 하는 다단연소 사이클 로켓엔진에는 산화제 과잉 예연소기가 사용된다. 예연소기는 터보펌프 구동을 목적으로 하기 때문에 예연소기 생성가스의 횡단면 온도분포는 터빈에 의해 제한되는 온도범위 내에서 균일하여야 하며 넓은 운전영역에서 안정적인 연소가 이루어져야 한다. 산화제 과잉 예연소기는 모든 추진제가 혼합헤드를 통해 분사되는 방식과 추진제를 혼합헤드와 연소실로 나누어 공급하는 방식이 있다. 기술검증을 위해 산화제 일부와 연료를 혼합헤드를 통해 연소실에 공급하여 1차 연소시키고 나머지 산화제를 연소실 냉각채널을 거쳐 연소실 중앙의 분사공을 통해 연소실로 주입하여 기화시키는 형태로 최종적으로 연소압 20MPa, 혼합비 60에서 작동하는 산화제 과잉 예연소기를 설계하여 연소시험을 수행하였다. 혼합헤드에는 별도의 점화용 분사기 없이 전체 연료 분사기를 통해 점화용 연료인 TEA/TEB 혼합물을 분사하여 점화하였다. 추진제를 2단으로 공급할 수 있도록 고안된 가압식 연소시험 설비에서 10회, 누적 60초 이상의 연소시험이 성공적으로 수행되었다. 연소시험결과 넓은 작동영역에서 안정적 연소특성과 생성가스 온도 분포의 균일성을 확인할 수 있었다. 고온 고압의 산화제 과잉 예연소기 기술 확보를 통해 케로신/액체산소 다단연소 사이클 로켓엔진 개발을 위한 기술적 기반을 마련하였다.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.16 no.1
• /
• pp.131-139
• /
• 2012

The lateral reinforcements of concrete such as hoops and spiral bars are known to confine concrete to compensate the strength loss due to fire by reducing explosive spalling and improving the capacity of ductility. In this context, a study was conducted to investigate the residual mechanical properties of confined and unconfined concrete($f_{ck}$=60MPa) after a single thermal cycle at 300, 600, $800^{\circ}C$. The main parameters required to establish the stress-strain relationship are the peak stress, the elastic modulus, and the strain at peak stress. The knowledge of the residual mechanical properties of concrete is necessary whenever the thermally damaged structure is required to bear a significant share of the loads, even after a severe thermal accident. Based on the results obtained in this study, the residual stress of confined concrete under thermal damage is higher according to the level of confinement and the larger strain made it to have better ductility. The decreasing ratio of elastic modulus from the relationship of stress and strain was also smaller than that of unconfined concrete.