• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2010.05a
• /
• pp.433-436
• /
• 2010

In this paper, heat/mass transfer characteristics on a film cooled stationary rotor blade are investigated using the naphthalene sublimation method. A row-speed annular wind tunnel with a single annular turbine stage is used. Three rows of film cooling holes are machined on the leading edge of the test blade. Detailed heat/mass transfer distributions are measured with changing the blowing rate from 1.0 to 2.0. As the blowing ratio increases, overall heat/mass transfer increases and the lower peak formed on the pressure side were disappeared.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.14 no.3
• /
• pp.685-693
• /
• 1990

The heat transfer coefficients were calculated numerically to see the effects of radiation around the porous medium put on the flat plate at a distance from the leading edge of flat plate for the two-dimensional laminar flows. To verify the analytical model developed and invoke the heat/mass transfer analogy, an experiment was carried out using naphthalene sublimation technique. From the effects of the wake, Sherwood number is maximum around the region where the porous medium is attached. The theoretical results correspond well with the experimental results at small Darcy number. Permeability of ceramic blocks used for experiment was also measured and the Forchheimer equation is applicable in our measurement range.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.15 no.5
• /
• pp.1756-1762
• /
• 1991

본 연구에서는 막냉각되는 터빈블레이드에서의 열전달 계수를 측정하기 위하 여 열전달과 물질전달의 상사관계를 이용하였다.터빈블레이드의 선단을 다른 연구 에서와 마찬가지로 원봉으로 모사하였고, 원봉의 표면에 위치하고 있는 1열의 분사홀 로부터 제트가 분사될 때 분사홀 근처 및 그 하류에서의 물질 전달계수를 측정하기 위 해 나프탈렌승화법을 이용하였다. 분사홀 열의 위치를 정체점에서 하류방향으로 이 동시키면서, 물질전달계수의 변화를 연구하였고, 분사율(M=.rho.$_{j}$ U$_{j}$ /.rho.$_{\infty}$ U$_{\infty}$)의 영향도 고찰하였다.

• Proceedings of the KSME Conference
• /
• 2007.05b
• /
• pp.2390-2395
• /
• 2007

The present research was experimentally performed to analyze the effect of delta-wing vortex generators(DWVG) on the heat transfer of fin surface of the plate fin-oval tube. The local heat transfer coefficient of the fin surface for four kinds of DWVG's arrangement was measured by the naphthalene sublimation technique for Reynolds numbers ranging from 2000 to 3200. The results showed that the heat transfer of the plate fin-oval tube can be significantly enhanced by DWVG for relatively low Reynolds numbers.

• Proceedings of the Korean Nuclear Society Conference
• /
• 1996.05b
• /
• pp.356-361
• /
• 1996

물질전달과 열전달의 유사성을 이용하는 나프탈렌 승화법을 핵연료집합체 모델에 적용하여 봉다발에서의 국소 열전달 계수의 분포를 측정하였다. 실험 모델은 가압경수형 원자로에서 나타나는 부수로 즉, 벽면 부수로와 모서리 부수로 및 내부 부수로로 구성되는 3$\times$3 봉다발이다. 봉다발에서의 국소 열전달 계수 값은 부수로의 형상과 인접한 봉 및 벽면의 영향이 크게 작용하는 것으로 측정되었다. 내부 부수로에 둘러져 있는 봉에서의 국소 열전달계수값은 봉과 봉 사이에서는 부수로 중심 방향보다 낮았고, 평균열전달계수는 Dittus-Boelter의 상관식보다 약간 낮은 값을 보였다. 벽면 부수로에 인접한 봉에서의 열전달계수는 벽면의 영향으로 내부 부수로에 있는 봉보다 상대적으로 낮았으며, 모서리 부수로의 봉에서는 벽면의 영향이 증대되어 더욱 낮게 나타났다.

• Proceedings of the KSME Conference
• /
• 2000.11b
• /
• pp.93-98
• /
• 2000

An experimental investigation on heat transfer characteristics of two-dimensional heated blocks using a confined impinging slot jet has been performed. At p/w=1, the effects of jet Reynolds number($Re=3900{\sim}12000$), dimensionless nozzle to block distance(H/B=1, 2, 4, 6) and nozzle type have been examined with five isothermally heated blocks. With the measurement of jet mean velocity and turbulence intensity distributions at nozzle exit, initially turbulent regimes, are classified. To clarify local heat transfer characteristics, naphthalene sublimation technique were used. The local and average heat transfer of heated blocks increase with the sharp-edged nozzle and increasing jet Reynolds number.

• Proceedings of the KSME Conference
• /
• 2000.11b
• /
• pp.272-277
• /
• 2000

The heat transfer characteristics of confined turbulent slot jet impingement on the flat plate with square rods(turbulence promoter) have been experimentally investigated at different nozzle configuration. The effects of jet Reynolds number (Re=3900, 5800, 7800, 9700), dimensionless slot-to-plate distance(H/B=4, 6, 8) and clearance(c) between square rods and the plate were examined. Measurement of heat transfer rate were conducted using naphthalene sublimation technique. When square rods were inserted over the heat transfer surface, heat transfer rate was slightly increased in the wall jet region and the sharp-edged orifice nozzle was heigher than squared orifice nozzle.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.21 no.8
• /
• pp.973-982
• /
• 1997

Effect of vortex generator on the heat transfer enhancement of electronic chips is investigated using naphthalene sublimation technique. Experiments are performed for a single chip and chip arrays, and shape of vortex generator, position of vortex generator, stream wise chip spacing and air velocity are varied. Local and average heat transfer coefficients are measured on the top surface of simulated electronic chips, and compared with those obtained without vortex generator. In case of a single chip, heat transfer augmentation is seen only on the upstream portion of chip surface, while heat transfer enhancement is found on the whole surface for chip arrays. Rectangular wing type vortex generator is found to be more effective than delta wing.

• Proceedings of the KSME Conference
• /
• 2000.04b
• /
• pp.119-124
• /
• 2000

The heat transfer characteristics of confined turbulent slot jet impingement on the flat plate with square rods(turbulence promoter) have been experimentally investigated. The effects of jet Reynolds number (Re=3900, 5800, 7800, 9700), dimensionless slot-to-plate distance(H/B=4, 6, 8) clearance(c) between square rods and the plate, and the length(d) of a side of the square rod were examined. Measurement or heat transfer rate were conducted using naphthalene sublimation technique. When square rods were inserted over the heat transfer surface, heat transfer rate was slightly increased in the wall jet region.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 1999.04a
• /
• pp.7-7
• /
• 1999

충돌/유출냉각은 연소실 벽면 등과 같이 열부하가 많이 걸리는 영역에서 고온의 연소가스로부터 표면을 보호하는 막냉각과 더불어 내부에 다공성 판을 설치하여 충돌제트에 의해 내부표면을 냉각시켜 가스터빈엔진의 고온요소의 냉각성능을 극대화시키는 방법 중의 하나이다. 이와 같은 냉각방법을 적용하면 벽면을 충돌제트에 의한 냉각과 함께 냉각유채를 막냉각에 활용함으로써 냉각효율을 극대화할 수 있다. 본 연구에서는 국소적인 값들을 획득하기 용이한 물질전달실험방법의 하나인 나프탈렌 승화법을 이용하여 수직으로 분사되는 충돌제트에 의한 유출판 내면에서의 열/물질전달특성을 분사판(injection plate)과 유출판(effusion plate) 사이의 높이, 분사제트의 속도, 분사홀간의 배열을 변화시켜가며 유출판만이 있는 경우와 비교, 분석하였다. 분사홀과 유출홀의 관 사이의 간격은 0.33d에서 10d까지 변화시켜가며 그 효과를 관찰하였으며, 홀배열 효과를 보기 위하여 2가지 홀배열(staggered array, shifted array)에 대하여 실험하였다. 또한 분사제트의 속도효과를 고찰하기 위하여 분사제트의 Rc$_{d}$=5,000-12,000까지 변화시켜가며 실험을 수행하였다.