• Journal of the Korea institute for structural maintenance and inspection
• /
• v.15 no.6
• /
• pp.85-91
• /
• 2011

This study aims at evaluating feasibility of Bottom ash-mixed Foam Cement Banking(BFCB) Method on the enhancement of soft soil, which is developed to reduce self-weight of banking by applying bottom ash and foam. to cement slurry. In order to measure the behavior of soil when BFCB layer was covered to soft ground, a testing equipment for mock-up test was fabricated and phased loads were applied up to measurement of yielding and ultimate strengths as well as movement of ground particles. In addition, these measured values such as settlement and heaving were compared with ones of surface-hardening method prevailing on soil improvement. As the result through mock-up test, BFCB showed lower values of ground deformation, while wider range of deformation was observed in compare to the other method. And settlement and heaving were measured lower, which implies the method developed is very effective to applicability of soft ground.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2000.02a
• /
• pp.90-90
• /
• 2000

이온빔을 이용한 리소그래피의 경우 미크론 이하의 미세구조를 형성할 수 있는 유용한 수단으로서 방사광 X-선과 함께 주목을 받고 있으며, 이와 같은 미세구조 제작은 MEMS (Micro Electro-Mechanical System) 개발에 있어서 매우 중요하다. 그러나 이온빔을 이용한 리소그래피에 대한 연구가 많이 이루어져 있지 않은 상태이다. MeV급 양정사 빔을 이용한 리소그래피의 가능성을 확인하기 위하여 기본적인 실험을 수행하였으며, 최적 이온빔 조사 조건 및 최적 현상 조건을 도출하였다. Resist로는 PMMA를 사용하였으며, 1.8 MeV 양성자 빔을 사용하여 50$\mu\textrm{m}$ 깊이의 구조물을 만들었다. 1.8MeV 양성자 빔의 조사선량이 7x1013ions/cm2 이상이 되면 PMMA 내부에 기포가 형성되므로 적정 조사선량을 4x1013 ions/cm2으로 결정하였다. 또한 선량을 4x1013ions/cm2 으로 고정하고 선량률을 변화시켜주면 선량률이 8x1011ions/cm2S 일 때부터 시료에 기포나 터짐 현상 등의 문제가 발생하였으며 5x1010~~1x1010ions/cm2s 의 선량률이 조사시간, 결함측면에서 가장 적합한 영역임을 알 수 있었다. 현상제로는 20% morpholine, 5% etanolamine 60% diethylenglykol-monobutylether, 15% 증류수를 혼합하여 사용하였다. 현상 온도를 30~5$0^{\circ}C$로 변화시켜서 현상을 한 결과, 4$0^{\circ}C$에서 현상 소요시간은 1시간 이내이며 SEM으로 관찰된 표면의 상태도 제일 양호한 결과를 보였다. 82 mesh 밀도, 선굵기 60$\mu\textrm{m}$, 크기 20x20 mm인 백금 망을 마스크로 사용하여 실제 3차원 미세구조를 제작하여 보았다. 그림 1에서 제작된 구조물의 SEM 사진을 보여주었으며, 식각된 면의 조도가 매우 뛰어나며 모서리의 직각성도 우수함을 확인할 수 있다. 이와 같이 도출된 시험 조건을 기초로 하여 리소그래피 후에 전기 도금을 이용한 금속 몰드 제작 및 이온빔 리소그래피 장점을 최대한 살릴수 있는 미세구조 제작에 대한 연구를 계속 추진할 계획이다.

• Journal of the Korean Recycled Construction Resources Institute
• /
• v.7 no.1
• /
• pp.57-65
• /
• 2019

In this study, the quality characteristics of the mother material of panel were evaluated for the production of moss panel using alumina cement and biological characteristics and environmental impact characteristics of moss panel were evaluated. The ratio of W/B 10%, Vs/Vm 20% and foaming agent 0.5% were selected as the basic mixing ratio for the mother panel of moss panel through pretest and SAP was added to improve the moisture content of panel. The optimal mixing ratio of SAP was considered to be less than 0.5% considering the quality characteristics. Also, through the use of alumina cement, the pH of the panel could be lowered to 10~11. The panel was able to improve the surface roughness through the foaming agent, and it was confirmed that the SAP had an effect of improving the moisture content of the panel. For the environmental impact characteristics of the moss panel, the moss panel evaluated the carbon dioxide reduction performance and the fine dust cleaning performance.

• Clean Technology
• /
• v.23 no.1
• /
• pp.80-89
• /
• 2017

The bubbling fluidized bed (BFB) reactor with a diameter of 0.1 m and a height of 1.2 m was used for experimental study of co-firing and emission characteristics fueled by sewage sludge (SS) and wood pellet (WP). The facility consists of a fluidized bed reactor, feeding system, cyclone, condenser and gas analyzer, The mean particle diameter and minimum fluidization velocity are $460{\mu}m$ and $0.21ms^{-1}$ respectively. SS produced from Korea and WP from Canada were examined. The various mixing ratios of WP were 20, 50, and 80% based on HHV. The equivalence ratio of 1.65, reactor temperature of $800^{\circ}C$, air flow rate of $100Lmin^{-1}$, and fluidization number of 4 were fixed in the BFB experiment. In TGA, the range of combustion temperature of SS was wider than that of WP. It represents that the combustibility of WP is higher than that of SS. The BFB reactor temperature was maintained between 800 and $900^{\circ}C$. CO emission of SS was high because of lower combustibility. $NO_X$ and $SO_X$ formation of SS were higher than that of WP since high nitrogen and sulfur contents of SS. CO, $NO_X$, and $SO_X$ formation were suppressed as the mixing ratio of WP was increased. The slagging and fouling tendencies show high in all test conditions.

• Journal of the Korean Recycled Construction Resources Institute
• /
• v.1 no.3
• /
• pp.225-232
• /
• 2013

The inorganic insulating material was fabricated with quartzite, ordinary portland cement(OPC), lime, anhydrous gypsum and foaming agent by hydrothermal reaction. The inorganic insulating material was fabricated by using autoclave chamber under high-temperature and high-pressure. The inorganic insulating material is a porous lightweight concrete. Because of its porous structure, properties of inorganic insulating material were light-weight and high-heat insulation property. Properties of fabricated inorganic insulating material were $0.26g/cm^3$ in specific gravity, 0.4MPa in compressive strength and 0.064W/mK in thermal conductivity. In this study, the inorganic insulating material was fabricated and analyzed at different size of quartzite/OPC, various foaming reagent and functional additives to improve the properties. Consequently, polydimethylsiloxane can improve density and thermal conductivity. Especially, polydimethylsiloxane showed excellent improvement in compressive strength.

• Journal of the Korean Recycled Construction Resources Institute
• /
• v.7 no.1
• /
• pp.37-43
• /
• 2019

This research studied production of lightweight filling production for sink hole restoration utilizing various industrial by-products(2kinds of fly ash, petro-cokes CFBC ash, blast furnace slag fine particle). For this purpose, the mixed raw material properties(compressive strength) behaviors according to the blending ratio of industrial by-products were examined by applying the experimental design method and statistical analysis was performed using the commercial program MINITAB. Compressive strengths of industrial by-products were strongly dependent on blast furnace slag powder. Compressive strength(3days aging) was 3~11MPa depending on the amount of blast furnace slag powder used. The use of CFBC fly ash was evaluated to have the least effect on compressive strength. In addition, the compressive strength and the coefficient of permeability were measured by preparing foamed concrete for the experimental batch 1 condition in the mixture experimental design. In this case, the bulk density is 0.9 to 1.0, the apparent porosity is 30 to 50%, the compressive strength(3days old) is 1 to 2MPa, and the permeability coefficient is $10^{-2}$ to $10^{-3}cm/sec$.

• Applied Chemistry for Engineering
• /
• v.8 no.5
• /
• pp.816-821
• /
• 1997

The hydrodynamics and the liquid flow characteristics were investigated in an internal circulation airlift reactor with a single nozzle as a gas distributor. In an air-water system, the gas holdup in the individual flow zone and the impulse-response curve of tracer were measured at various gas velocities and reactor heights. Experimental results showed that for the higher gas velocity(>about 8 cm/s), the flow behavior of bubbles in the riser was turbulent flow due to strong bubble coalescences and the axial height of dispersion zone of large bubbles having uniform sizes in the downcomer was decreased with increasing gas velocity. And mean gas holdups in the individual flow zone and the reactor were increased with increasing gas velocities and were decreased with increasing heights of the top section of the reactor and it was decreased with increasing the height of the top section and gas velocity. Flow characteristics of liquid in the riser and the downcomer was tend to access to plug flow and the overall flow behavior of liquid was mainly varied with the size of the top section which it was assumed to be perfect mixing zone. In these conditions, liquid circulation velocities were increased with increasing gas velocities and they were higher than those by using other gas distributors.

• Journal of Dental Rehabilitation and Applied Science
• /
• v.37 no.4
• /
• pp.217-224
• /
• 2021

Purpose: The purpose of this study was to evaluate the porosity of resin modified glass ionomer (RMGI) by different mixing methods. Materials and Methods: Five specimens were prepared for each groups according to capsules and mixing methods. Two RMGI capsule and two mixing machines were used for this study. One resin-modified glass ionomer cement is Fuji II LC (F2LC) and the other is Photac Fil Quick Aplicap (PFQ). For Mixing of RMGI capsule, Rotomix using rotating motion and CM-II using shaking motion were used. After measuring height, radius and mass of specimens, Density was calculated. And porosity was measured using micro-computed tomography (micro-CT). All data were statistically analyzed using T-test, two-way ANOVA to compare between groups at 95% significance level to evaluate the affect of capsule and mixing method on the porosity. Results: The porosity was observed in all specimens generally. And there is significant differece between porosities according to RMGI capsule and Mixing method. The porosity of PFQ was lower than that of F2LC and the porosity of Rotomix was lower than that of CM-II. Conclusion: There was a difference of porosity according to kind of capsules and mixing methods. When using same capsule, less porosity was observed on PFQ than F2LC. When using same mixing mehod, less porosity was observed on Rotomix than CM-II. Using mixing machine of same coporation as that of RMGI capsule did not lead to lower porosity. Therefore, Selecting optimal mixing machine is important.

• Journal of Energy Engineering
• /
• v.6 no.2
• /
• pp.203-211
• /
• 1997

This study is on the separation of Global warming effect gas, CO$_2$by chemical absorption from mixture of CO$_2$-N$_2$which was modeled after flue gas of fire power plant. Investigation of optimum condition for absorbent was carried out by using sparged vessel apparatus. Through packed tower experiments, applicabilities of two absorption models were tested by comparing experimental results with theoretical values. Absorbent used in the experiments was Monoethanolamine (MEA) and gas mixture was made in the mole composition of 15% CO$_2$and 85% N$_2$. Through estimations of CO$_2$loading and CO$_2$removal efficiency, optimum concentration of absorbent was found in the range of 4-5 M. To find a rate of absorption, an enhancement factor was introduced. Values of rate of absorption were calculated by Film model and Higbie model, respectively. Higbie model showed good agreement with experimental results. Therefore, this models is considered to be applicable to the CO$_2$separation process for flue gas from fire power plant.

• Journal of the Society of Naval Architects of Korea
• /
• v.34 no.4
• /
• pp.42-52
• /
• 1997

The basic principle of underwater ram-jet as a unique marine propulsion concept showing vary high cruise speed range(e. g. 80-100 knots) is the thrust production by the transfer of the potential energy of compressed gas to the operating liquid through kinetic mixing process. This paper is aimed to investigate the propulsive efficiency of the nozzle flow in underwater ram-jet at the speed of 80 knots for the buried type vessel. The basic assumption of the theoretical analysis is that mixture of water and air can be treated as incompressible gas. For an optimized nozzle configuration obtained from the performance analysis, preliminary data for performance evaluation are obtained and effects of nozzle inner wall friction, ambient temperature, ambient pressure, water density, gas velocity, bubble radius, flow velocity, diffuser area ratio, mass flow ratio and water velocity gradient are investigated.