• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.18 no.9
• /
• pp.2223-2228
• /
• 2014

Available shafts with gears at each end of the cylinder-shaped steel are widely used as power train components for automobiles. In order to automate the production of a geared shaft, there are problems to be solved. After one side of the cylinder is cut in gears, one of the problems is to determine the position of the cylinder which has been already cut. The shaft is then to be fed ahead with geared position to the chuck with jaws in geared shape. The other problem is to acquire information on an angular position of the shaft to fit to the jaws of the chuck. This paper deals with the magnetic detection sensor of gear position. Coils are installed in two places. Self-inductances of coils are detected by the changes of reluctance and are then compared. The magnetic analysis also has been carried out by the finite element analysis (FEM).

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.35 no.11
• /
• pp.1477-1482
• /
• 2011

Using a one-way clutch has been reported to be very effective in reducing the vibration of gear pairs. However, study on the effect of using a one-way clutch has been based on numerical analysis only, and no experimental study has yet been executed. Hence, in this study, experiments to verify the effectiveness of using a one-way clutch to reduce the torsional vibration have been executed. Dynamic responses over a wide range of speeds have been compared for various numbers and positions of the clutch. The results of the experiments verified that a one-way clutch is effective in reducing the vibration by decreasing the tooth mesh vibration as well as the vibration transmitted from the input shaft.

• Journal of Advanced Marine Engineering and Technology
• /
• v.39 no.9
• /
• pp.895-902
• /
• 2015

In this paper, finite element analysis of a cycloidal pitch reducer for a 2 MW-class wind turbine is reviewed. The system is composed of one cycloid set, one spur gear set, an input shaft, an output shaft, and a housing. The system was also evaluated for stability by analyzing spur gear strength according to ISO 6336. An analysis of the natural vibration characteristics of the 2 MW-class wind turbine cycloid pitch reducer was performed with attention to critical speed with input mass unbalance, output mass unbalance, spur gear transmission error, cycloid gear transmission error, and excitation frequency.

• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.29 no.1
• /
• pp.37-44
• /
• 2016

This study is concerned with the numerical investigation of dynamic characteristics of 2.5MW-class wind turbine gearbox in which the misalignment improvement of plenary gear shafts by the flexible pins and the dynamic impact response are analyzed by the finite element method. The tooth contact between gears is modelled using the line element having the equivalent tooth stiffness and the contact ratio to accurately and effectively reflect the load transmission in the internal complex gear system. The equivalent tooth stiffness is calculated by utilizing the tooth deformation analysis and the impulse torque is applied to the input shaft for the dynamics response characteristic analysis. Through the numerical experiments, the equivalent tooth stiffness model was validated and the misalignment improvement of planetary gear shafts was confirmed from the comparison with the cases of fixed shafts at one and both ends.

• Journal of Advanced Marine Engineering and Technology
• /
• v.37 no.6
• /
• pp.631-637
• /
• 2013

The characteristics of involute gear pump with eccentric gap between gear tip and housing have been studied in terms of volumetric flow rate and/or flow efficiency. The analysis has been done with FLUENT/R-13 employing with k-e model for the turbulent flow under the given conditions of rotational velocity, gap distance and outlet pressure. The effect of parameters continues to be shown for the eccentric gear as same as for the concentric gear such that the volumetric flow rate (volumetric efficiency) increases as the increases of rotational velocity and decrease of gap distance and of outlet pressure. In the meantime, the shape of pressure build-up appears to be exponentially increase as gap distance decreases at upstream position. The pressure is rapidly developing in the upstream and remains almost constant thereafter in the downstream of circumferential flow path. This typical characteristics becomes more profound as eccentricity increases. The pump performance for the eccentric gear pump with minimum gap distance shows better than its concentric counterpart. However, it shows not for the concentric pump with minimum gap distance. Therefore, the gap reduction due to eccentricity may be positive for pump performance.

• Journal of the KSME
• /
• v.53 no.2
• /
• pp.30-34
• /
• 2013

기어는 사람에 의해 사용된 가장 중요한 기계 중의 하나이며, 회전하는 두 축 사이에 운동과 동력을 전달하고 회전 방향과 속도를 변경하는 역할을 한다. 기어는 우리가 손에 차는 시계나 벽시계뿐만 아니라 자동차, 기차, 선박, 비행기에서 엔진의 동력을 전달하여 바퀴나 혹은 프로펠러를 돌리기 위해 사용된다. 또한 장난감, 복사기, 팩스, 풍력발전기에 사용하는 등 그 용도가 다양하다. 이 글에서는 기어의 역사를 간단히 살펴보고 기어의 진동 소음에 관련된 연구 주제에 대해 기술한다.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2004.05a
• /
• pp.250-250
• /
• 2004

자동차의 시동을 걸기 위해서는 맨 처음 엔진을 강제로 가동시키는 기계장치가 있어야 하며, 이를 시동모터라 한다. 시동모터는 모터부와 그 부속장치 그리고 발생된 힘을 엔진으로 전달하는 동력전달 기구로 구성되어 있다. 동력전달기구는 플라이 휠이라는 부품을 크랭크 축 끝단에 장착한 후 그 원주상에 링 기어를 만들고, 시동모터의 축에 피니언이라는 작은 기어를 맞물리게 하여 시동 키를 돌리면 이 기어가 회전되는 원리를 이용하고 있다. 피니언 기어는 작고 반대로 플라이 휠에 장착되어 있는 링 기어는 크기 때문에 일정한 기어비가 형성되어 큰 부하의 엔진회전이 가능하다.(중략)

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.36 no.9
• /
• pp.1027-1032
• /
• 2012

Two types of very small multiplying gears and arrays have been developed for new dental hand-pieces, and the increased speed ratios, modules, number of teeth, gear diameters, and gear types were calculated based on the dynamics of the machinery. The contacting and bending strengths were evaluated for gear teeth with two design concepts using AGMA equations and finite element analyses, and the contacting stresses on teeth with and without DLC (diamond-like-carbon) coating layers were calculated. Fatigue and tension tests were performed to obtain an S-N curve, the Young's modulus, and the strength of the gear material, and these were utilized in the analyses. Slightly larger stresses were found for 2-axis-type gears than for other types of gears, and the S-N curves showed that a gear lifetime of 109 cycles was satisfied. The contacting stresses in gears coated with DLC were reduced by 30%. A new prototype model of a hand-piece with small gears was successfully fabricated and tested.

• Journal of Advanced Marine Engineering and Technology
• /
• v.38 no.3
• /
• pp.253-261
• /
• 2014

In this paper, vibration analysis of power differential gear train for 2.5MW wind turbine system is analyzed. which system is composed of two planetary gear set, one helical gear set and main shaft that connected by flange. Planetary gear set, helical gear set, main shaft are modeled in MASTA program and housing, torque arm, carrier, flange components are modeling by finite element method. Each models are combined by component mode superposition. To analysis of natural vibration characteristic about 2.5MW wind turbine gear train was performed and check about critical speed with wind load, mass unbalance, angle misalignment excitation frequency.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.48 no.12
• /
• pp.953-960
• /
• 2020

This paper presents an optimization of gear web design used in a main gear train of an engine reduction gearbox for a rotorcraft. The optimization involves the minimization of a total weight, transmission error, misalignment, and face load distribution factor. In particular, three design variables such as a gear web thickness, location of rim-web connection, and location of shaft-web connection were set as design parameters. In the optimization process, web, rim and shaft of gears were converted from the 3D CAD geometry model to the finite element model, and then provided as input to the gear simulation program, MASTA. Lastly, NSGA-II optimization method was used to find the best combination of design parameters. As a result of the optimization, the total weight, transmission error, misalignment, face load distribution factor were all reduced, and the maximum stress was also shown to be a safe level, confirming that the overall gear performance was improved.