• Clean Technology
• /
• v.11 no.2
• /
• pp.105-116
• /
• 2005

Carboxymethylcellulose(CMC) which is water soluble at room temperature was manufactured from the cellulose material in this study. Experimental parameters were reaction temperature, time and concentration of NaOH and monochloroacetic acid. CMC was tested for solubility, degree of substitution(D.S.) and tensile strength. The surface structure of CMC fiber was tested using scanning electron microscope(SEM). CMC manufactured from viscose rayon was affected by the chemical concentration rather then the reaction time and temperature. Also, degree of substitution is closely related to the solubility of the CMC.

• The Journal of Korea Institute of Information, Electronics, and Communication Technology
• /
• v.3 no.1
• /
• pp.24-30
• /
• 2010

In this paper, a novel electrically small monopole type resonant antenna is proposed. The very short length monopole (${\iota}{\approx}{\lambda}_g/15$ ) acts as a capacitive element and the slot on the ground structure acts as an inductive element, hence the combined system with these two elements thus form an LC resonator. The equivalent circuit model of the antenna structure was used to analysis and qualify the design correctness. Although the proposed antenna has very small size, it shows good performances. The measured maximum gain and radiation efficiency of the fabricated antenna at the frequency of 2.1 GHz was 3.6 dBi and 77.8 %, respectively.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.14 no.9
• /
• pp.912-918
• /
• 2003

In this paper, we designed and implemented the dual band monopole antenna for cellular CDMA(Code Division Multiple Access) and IMT-2000(International Mobile Telecommunication 2000) repeater. The antenna was designed by using 3D simulations program, HFSS(High Frequency Structure Simulator). Electrical characteristics were measured by using HP 8720C network analyzer and measured maximum S$\_$11/ was -10.9 dB for all frequency bands of interests in Cellular CDMA and IMT-2000. Simulation results for antenna gain at 859 MHz and 2027.5 MHz were 2.38 dBi and 4.02 dBi respectively with omni directional radiation pattern. The size of implemented antenna is compact and the antenna can be produced in low cost enough for commercialization.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.22 no.7
• /
• pp.667-675
• /
• 2012

A damage estimation method for support structure of offshore wind turbine using modal parameters is presented for effective structural health monitoring. Natural frequencies and mode shapes for a support structure with monopile of an offshore wind turbine were calculated considering soil condition and added mass. A neural network was learned based on training patterns generated by the changes of natural frequency and mode shape due to various damages. Natural frequencies and mode shapes for 10 prospective damage cases were input to the trained neural network for damage estimation. The identified damage locations and severities agreed reasonably well with the accurate damages. Multi-damage cases could also be successfully estimated. Enhancement of estimation result using another parameters as input to neural network will be carried out by further study. Proposed method could be applied to other type of support structure of offshore wind turbine for structural health monitoring.

• Journal of Korean Society of Coastal and Ocean Engineers
• /
• v.22 no.5
• /
• pp.306-315
• /
• 2010

As developing the large-scale offshore wind farm is expected, the preliminary environmental impact assessment is very essential. In this study, the wave hindcast model is verified based on observed data at the coast around Wido which is among the candidate sites for developing the offshore wind farm. In addition, the effect of the wind turbine foundations on wave height is analyzed when total 35 wind turbines including monopile foundations of 5 m in diameter are installed. Calculation result of significant wave height is in good accord with observed data since the RMS error is 0.35 m. Moreover, it is found that the presence of the wind turbine foundations hardly affects wave height as wave damping ratio is less than 1%.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.11 no.1
• /
• pp.55-62
• /
• 2000

In this paper, cellularphone antenna was designed to be capable of being mounted on the circuit-board with co-planar feeding method. The designed antenna is fabricated by the following procedure : make the multi-layered dielectric ceramic($\varepsilon_{\tau}$=23) hexahedron($7.5mm\times4.5mm\times0.4mm$) and then produce λ/4 monopole radiation element with helical structure on the surface of the hexahedron. The results are as followings : Returnloss 27.36 dB, -10 dB bandwidth 76 MHz(3.97 %), H-plane average gain -9.43 dBd.

• Journal of Broadcast Engineering
• /
• v.23 no.6
• /
• pp.925-930
• /
• 2018

In this paper, we present a low profile dual-microstripline-fed double 4-arrayed meander monopole antenna with a cross-type element back by separated four-segments mesh-type reflector. The cross-type element and separated four-segments mesh-type reflector leads to enhance radiation patterns and antenna gain characteristics. The measurement value of the proposed antenna show that it has dipole-like radiation pattern characteristics. The experimental peak gain of fabricated antenna is about 2.89 dBi, which presents relatively high gain characteristics for a low profile(small-size) one. This antenna can be applied mobile RFID(radio frequency identification) readers, small medical instruments, broadcasting and home-networking operations, and other low profile high-gain systems.

• Journal of the Institute of Electronics Engineers of Korea SC
• /
• v.43 no.6 s.312
• /
• pp.48-60
• /
• 2006

This paper presents three PWM modulators using CMOS OTAs. They consist of a ramp integrator and current-tunable Schmitt triggers. Prototype circuits built using discrete components exhibited that their duty cycles are linearly controllable. The proposed modulators can be easily fabricated in a monolithic IC, because they have a simple structure.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.14 no.11
• /
• pp.1121-1126
• /
• 2003

In this paper we show impulse generator which is important component in UWB communication. There is two steps to generate monocycle impulse. In first step, Gaussian pulse was made by operation of transistor switching and operation time of transistor switching. The second step the high pass filter change from Gaussian to Monocycle impulse. The result of this impulse generator is impulse whose pulse width is 0,9 ns in time domain and amplitude is +/-250 ㎷.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.45 no.4
• /
• pp.300-309
• /
• 2017

A spacecraft obtains a reaction momentum required for an orbit correction and an attitude control by exhausting a combustion gas through a small thruster in space. If the exhaust plume collides with spacecraft surfaces, it is very important to predict the exhaust plume behavior of the thruster when designing a satellite, because a generated disturbance force/torque, a heat load and a surface contamination can yield a life shortening and a reduction of the spacecraft function. The purpose of the present study is to ensure the core technology required for the spacecraft design by analyzing numerically the exhaust gas behavior of the 10 N class bipropellant thruster for an attitude control of the spacecraft. To do this, calculation results of chemical equilibrium reaction between a MMH for fuel and a NTO for oxidizer, and continuum region of the nozzle inside are implemented as inlet conditions of the DSMC method for the exhaust plume analysis. From these results, it is possible to predict a nonequilibrium expansion such as a species separation and a backflow in the vicinity of the bipropellant thruster nozzle.