• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.17 no.1
• /
• pp.56-61
• /
• 2005

Indoor air quality becomes of a concern recently in view of human health. This study investigates the air diffusion performance and the air change efficiency of a classroom, when outdoor air is introduced in addition to the heating/cooling operation of a ceiling-mounted heat pump. A CFD analysis has been performed to investigate the effect of the discharge angle of the air jets from the heat pump for both parallel and series types of outdoor air system. It is observed that the series type creates more uniform indoor environment compared to the parallel type in general. It can be concluded the discharge angle should not be larger than 40o for the parallel type, in order not to generate thermal stratification in the room.

• Proceeding of KASS Symposium
• /
• 2008.05a
• /
• pp.3-8
• /
• 2008

The purpose of this study is to provide fundamental cooling design data for the large public enclosures as gymnasium. This study executed indoor thermal environment verification of the existing gymnasium by measuring temperature distribution with cooling the space in summer. Cooling loads from human body was not considered. We examined various indoor thermal environment factors of the large enclosed space in this study which include vertical and horizontal temperature distribution, supply and return air flow feature, thermal comfort environment feature, amount of ventilation and etc.

• Journal of Korean Association for Spatial Structures
• /
• v.5 no.4 s.18
• /
• pp.101-108
• /
• 2005

The investigations for mitigating wind-induced excitations of tall buildings have been carried out. The aerodynamic modification of a building shape changing the cross-section with height through tapering, which alters the flow pattern around the building, could reduce wind induced excitations of tall buildings. The fart that a tapered tall building might spread the vortex-shedding over a broad range of frequencies makes more effective for reducing acrosswind responses has been established. In this paper, to investigate the tapering effect for reducing wind-induced responses of a tapered tall building, high-frequency force-balance test was conducted. The six types of building models which have different taper ratio of 2.5%, 5%, 7.5%, 10%, 15% and one basic building model of a square cross-section were tested under the two typical boundary layers representing suburban and urban flow environment. The effect of wind direction was also considered.

• Journal of Korean Association for Spatial Structures
• /
• v.7 no.6
• /
• pp.91-101
• /
• 2007

The purpose of this study is to provide fundamental cooling design data for the large public enclosures as gymnasium. This study executed indoor thermal environment verification of the existing gymnasium by measuring temperature distribution with and without cooling the space in summer. Colling loads from human body was not considered. We examined various indoor thermal environment factors of the large enclosed space in this study which include vertical and horizontal temperature distribution, supply and return air flow feature, thermal comfort environment feature, amount of ventilation and etc.

• Proceedings of the Materials Research Society of Korea Conference
• /
• 2010.05a
• /
• pp.52.2-52.2
• /
• 2010

각종 전자 및 산업용 기기, 수송기기류의 고성능화에 따라 다양한 특성을 갖는 합금판재에 대한 수요도 증가하여, 기존의 합금판재의 성질이외의 기능성이 추가된 새로운 판재 제조기술 확보의 필요성이 증가하고 있다. 그러나 기존의 합금 설계 및 조직제어방법으로는 새로운 기능을 갖는 합금 판재의 개발에는 한계가 있으며 따라서 기존 특성이외에 여러 가지 기능성을 부여하는 판재의 제조를 위한 새로운 기술 개발이 요구되고 있다. 특히 경량재료로서 그 사용량이 계속 증가하고 있는 알루미늄 판재에 대하여 내 외부 층의 조성이 다른 합금으로 이루어진 다층 금속판재 제조방법을 도입함으로써 내식성, 열전도성, 브레이징성 등의 다양한 기능성이 부여된 알루미늄 판재의 제조가 가능하다. 본 연구에서는 다양한 기능성을 갖는 다층 금속 복합판재를 제조하기위하여 압연접합기술을 적용하고 다양한 합금계의 조합을 통하여 기능성이 향상된 다층 알루미늄 판재를 제조하는 기술을 개발하였다. 먼저 경량 열교환기 제조에 사용되고 있는 브레이징용 알루미늄 클래드재 제조를 위하여 여러 가지 압연접합 조건에서 알루미늄 클래드 재를 효율적으로 제조하는 방법을 개발하였다. 또한 기존의 고강도 알루미늄 합금에 대하여 내 외부합금층을 달리하여 다층 알루미늄 판재를 제조하고 기계적 특성 변화을 평가하였으며 새로운 특성을 갖는 알루미늄 판재의 제조가능성을 타진하였다.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.29 no.7 s.238
• /
• pp.868-877
• /
• 2005

We performed the experimental and the numerical study on the comparison of thermal comfort performance indices for cooling loads in the lecture room for 4 cases: Fan coil unit(FCU) or 4-way cassette air-conditioner is respectively operated with the ventilation system or without. We measured the velocity, the temperature distribution and predicted mean vote(PMV) value in the lecture room for 4 different air-conditioning methods. Effective draft temperature(EDT) and PMV were investigated to analyze the characteristics of two thermal comfort indices in the lecture room and to compare their values each other. From the results we knew that there is the similarity between PMV values and EDTs when the room is air-conditioned for cooling loads. It turned out that definition of the control temperature is very important when the EDT is calculated. Finally EDT should not be used to predict the accurate thermal comfort in case that the temperature and humidity are suddenly varied and the zone affected by the solar and inner wall radiation.

• Fire Science and Engineering
• /
• v.25 no.4
• /
• pp.94-102
• /
• 2011

Hot smoke test is done in a subway tunnel. Alcohol trays of 1.0 MW and smoke generators are used for generating hot smoke. The fans equipped with the tunnel are successively run 9 min after smoke generation. It is verified how hot smoke is controlled by fans. Velocity and direction of flow, temperature and smoke density are measured and analyzed for smoke control performance of the tunnel with fans and analyzed from the fire-safety-point of view. Velocity of smoke flow is obtained by using measured velocity and temperature at the ceiling of the tunnel. The time when smoke-control flow is builded up is different for the different positions. Velocity distributions at various positions will be used for the boundaries and the comparison data in numerical simulations for evaluation on smoke-control facilities of subway tunnel.

• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.23 no.12
• /
• pp.828-835
• /
• 2011

The purpose of this study is to analyze and evaluate the 3 types of indoor ventilation methods such as natural, mechanical, and hybrid ventilation in high-rise building which is affected by stack effect and outdoor air pressure. For the evaluation of the ventilation capacity, CFD simulation was performed in a typical high-rise residential building. The results of the simulations are as follows: 1) Natural ventilation method is not enough to the regulation. 2) In case of mechanical ventilation, congested area is occurred but meets the regulation. 3) In case of hybrid ventilation with stack effect, all the areas of indoor meet the regulation and congested area is reduced. 4) In case of high-rise building, the differences of ventilation rate among houses in the building are not large because the mechanical ventilation is main factor.

• Journal of The Korean Society of Agricultural Engineers
• /
• v.54 no.5
• /
• pp.79-89
• /
• 2012

The objectives of this paper were to evaluate the wind flow behind the livestock ventilation fan for small-scale wind power generation and to make flow profiles of imaginary ventilation fan for future simulation works. The field experiments using typical 50-inch fan indicated that the wind flow behind the ventilation fan had a good possibility of power generation with its high and steady wind speeds up to a distance of 2 m. The expected electricity yield was almost 101~369 W with a small (0.8 m radius) wind turbine. The decline of ventilation fan performance caused by the obstacle was also not significant with about 4 % from a distance of 2 m. The flow profiles for the computational fluid dynamics (CFD) simulation was created by combining the direction vectors analyzed from tuft visualization test and the flow predicted by the rotating fan modeling. The flow profiles are expected to provide an efficient saving of computational time and cost to design a better wind turbine system in future works.

• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.16 no.3
• /
• pp.303-309
• /
• 2004

In order to improve thermal comfort in the Rotunda, which is high and wide visiting space of the new national museum of Korea, eight ventilating fans were installed near the ceiling of Rotunda. It has been analyzed thermal comfort of Rotunda with/without ventilating fans by numerical simulation. To evaluate thermal comfort of the Rotunda, well-known indices, PMV and PPD were introduced. The results of present investigation show that temperature distribution of the case with fans is closer to target temperature than the case with-out fans at the breathing zone. In the case without fans, thermal stratification with 16$^{\circ}C$ of temperature difference occurs along the height of the Rotunda which makes the thermal environment worse and the PPD values reach up to 50% in the 6th floor connection passage. In the case with fans, however, the vertical temperature difference were reduced to 9$^{\circ}C$ and the PPD values were lower below 20%. Consequently, the ventilating fans adopted on this study are effectively used for improving the thermal comfort in large space structure with thermal stratification.