• The Journal of the Korea Contents Association
• /
• v.22 no.3
• /
• pp.54-61
• /
• 2022

Ship is a huge system including a variety of pipe arrangements. Pipes are installed according to the design layout, however the end poistion of pipes are not well matched owing to its measurement and construction errors. In this situation, the customized pipe fitting is frequently designed to connect with both pipes, the position of which are manually measured. This paper focused that these two coordinates are measured by point cloud from RGBD sensor and the relative transformation induced by positional and orientational differences is calculated by inverse kinematics in robotics theory. Therefore, the result applies for the methodology of the pipe connection design. The pipe coordinate that is estimated by the matching and the probabilistic RANSAC method will be verified by experiments. The kinematic design parameters are computationally calculated by using the minimum degree of freedom that connects both pipe coordinates.

• Journal of Institute of Control, Robotics and Systems
• /
• v.8 no.6
• /
• pp.498-505
• /
• 2002

Reducing odometer errors caused by kinematic imperfections in wheeled mobile robots is imestigated. Wheel diameters and wheelbase are corrected by using encoders without landmarks. A new velocity trajectory is proposed that compensates for an orientation error due to acceleration- resolution constraints on motor controllers. Based on this velocity trajectory, the wheel velocity of one out of two driven wheels may be changed by the traveled distance of the mobile robot. It is shown that a wheeled mobile robot can't move along a straight line exactly, even if kinematic correction are achieved perfectly, and this phenomenon is attributable to acceleration-resolution constraints on motor controllers. We experiment on a wheeled mobile robot with 2 d.o.f. are used in the experiment to verify the proposed scheme.

• The Bulletin of The Korean Astronomical Society
• /
• v.37 no.2
• /
• pp.150.2-150.2
• /
• 2012

로켓 엔진용 짐벌 마운트는 발사체 발사 후 자세 제어를 위해 발사체와 엔진사이에 장착된 TVC(Thrust Vector Control) 구동기의 작동으로 짐벌 운동을 수행하며 기구학적으로 자세 제어를 하는데 있어 매우 중요한 역할을 하는 요소이다. 이러한 짐벌 마운트는 엔진 추력을 발사체에 전달하는 기능 이외에 지정된 위치에 엔진을 고정시키는 역할과 위치 고정 후 발사체 단과 엔진의 정확한 추력 전달을 위한 기계적 불일치 보정 기능, 짐벌 구동에 대한 피봇 기능을 동시에 수행하여야 하는 복합적인 기능을 가지고 있다. 특히, 이중에서도 물리적으로 고 추력의 하중을 전달하는 요소로서 충분한 강도와 강성을 지녀야 하므로 본 연구에서는 이와 관련된 초기 설계 요구도 분석을 바탕으로 설계 규격에 부합하는 짐벌 마운트의 구조적 검토를 통해 로켓 엔진용 짐벌 마운트 설계 형상을 개념적으로 제시하였다.

• Journal of the Korean Society for Precision Engineering
• /
• v.21 no.5
• /
• pp.83-83
• /
• 2004

The analysis of relative pose(position and rotation) between stereo cameras is very important to determine the solution that provides three-dimensional information for an arbitrary moving target with respect to robot-end. In the space of free camera-model, the rotational parameters act on non-linear factors acquiring a kinematical solution. In this paper the general solution of active stereo that gives a three-dimensional pose of moving object is presented. The focus is to achieve a derivation of linear equation between a robot′s end and active stereo cameras. The equation is consistently derived from the vector of quaternion space. The calibration of cameras is also derived in this space. Computer simulation and the results of error-sensitivity demonstrate the successful operation of the solution. The suggested solution can also be applied to the more complex real time tracking and quite general and are applicable in various stereo fields.

• Journal of the Korean Society for Precision Engineering
• /
• v.21 no.5
• /
• pp.89-90
• /
• 2004

The analysis of relative pose(position and rotation) between stereo cameras is very important to determine the solution that provides three-dimensional information for an arbitrary moving target with respect to robot-end. In the space of free camera-model, the rotational parameters act on non-linear factors acquiring a kinematical solution. In this paper the general solution of active stereo that gives a three-dimensional pose of moving object is presented. The focus is to achieve a derivation of linear equation between a robot's end and active stereo cameras. The equation is consistently derived from the vector of quaternion space. The calibration of cameras is also derived in this space. Computer simulation and the results of error-sensitivity demonstrate the successful operation of the solution. The suggested solution can also be applied to the more complex real time tracking and quite general and are applicable in various stereo fields.

• Journal of the Korean Society of Industry Convergence
• /
• v.24 no.6_2
• /
• pp.947-952
• /
• 2021

In this paper, the simplified kinematic error model for Delta parallel robot is presented, which can enable the analytical forward kinematics essentially for kinematic calibration calculations instead of the numerical one. The simplified kinematic error model is proposed and the forward kinematics including the error parameters is analytically derived. The kinematic calibration algorithm of the Delta parallel robot with 90 degree arrangement using laser tracker and the experiment result are presented.

• Transactions of the Korean Society of Machine Tool Engineers
• /
• v.13 no.3
• /
• pp.44-52
• /
• 2004

This paper proposed a error compensation methodology for three-DOF translational parallel manipulator. The proposed method uses CMM (coordinate measuring machine) as metrology equipment to measure the position of end-effector. To identify the transform relationships between the coordinate system of the parallel manipulator and the CMM coordinate system, a new coordinate referencing (or coordinate system identification) technique is presented. By using this technique, accurate coordinate transformation relationships are efficiently established. According to these coordinate transformation relationships, an equation to calculate the compensating error components at any arbitrary position of the end-effector is derived. In this paper, Monte Carlo simulation method is applied to simulate the compensation process. Through the simulation results, the proposed error compensation method proves its effectiveness and feasibility.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.17 no.6
• /
• pp.1431-1440
• /
• 1993

This paper presents a new NC machine performance test and calibration system. In order to measure NC machine erros in simpler, and less time-comsuming way, some indirect measuring systems such as circular disk system and double ball bar system have been developed instead of laser interferometer. But these indirect measuring systems have shown their limits in identifying each of NC machine error sources in absolute numerical value. Therefore, we developed an unique NC machine error measurement system which provides a simple measuring process like other conventional indirect methods and still can indentify each of NC machine error sources in absolute numerical value.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.27 no.4
• /
• pp.647-655
• /
• 2003

This paper studies the observability of calibration system with a constraint movement by a constraint operator. The calibration system with the constraint movement need only simple sensing device to check whether the constraint movements are completed within an established range. However, it yields the concern about the poor parameter observability due to the constraint movements. This paper uses the QR-decomposition to find the optimal calibration configurations maximizing the linear independence of rows of a observation matrix. The number of identifiable parameters are examined by the rank of the observation matrix, which represents the parameter observability. The method is applied to a parallel typed machining center and the calibration results are presented. These results verify that the calibration system with low-cost indicators and simple planar table is accurate as well as reliable.

• Journal of the Korean Society for Precision Engineering
• /
• v.14 no.1
• /
• pp.69-77
• /
• 1997

본 논문은 금형의 마무리 연마 작업을 로봇을 이용하여 자동화하기 위한 오프라인 프로그래밍 시스템개발을 그 내용으로 하고있다. 3차원 자유곡면 형상을 갖는 금형을 연마하기 위한 로봇 작업 경로를 효율적으로 생성하기 위해서는 기존의 교시 방법이 아닌 CAD시스템과 연계된 시뮬레이션 방식의 자동 경로 생성 방법이 요구된다. 본 연구에서 개발된 금형 연마 작업을 위한 오프라인 프로그래밍 시스템은 연마 작업 시뮬레이션을 위한 기하학적 모델링 기능, 로봇의 작업 공간을 고려한 작업장 배치 기능, 연마 로봇의 효율적인 기구학 해, 3차원 그래픽 시뮬레이션, 3차원 물체간의 충돌 검사 기능 및 유기적인 관계형 데이타 베이스 기능 등으로 구성된다. 본 시스템의 시뮬레이션 결과를 로봇의 위치 보정 과정을 거쳐 로봇 작업 프로그램 으로 변환함으로써 최종적으로 실제 연마 작업이 가능한, 정확하고 안전한 로봇 프로그램을 생성하였다.