• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.34 no.8
• /
• pp.755-760
• /
• 2010

In this study, we mainly focused on the PM (Particulate Matter) emission characteristics of a diesel engine. To analyze particle behavior in the tail-pipe, particle emission was measured on the engine-out (downstream of turbocharger), each upstream and downstream both of DOC (Diesel Oxidation Catalyst) and DPF (Diesel Particulate Filter). Moreover, particle emission contours on each sampling point were constructed. The reduction efficiency of particle number concentration and mass through the DOC and DPF was studied. Parameters such as EGR (Exhaust Gas Recirculation) and the main injection timing were varied in part load conditions and evaluated using the engine-out emissions. The DMS500 (Differential Mobility Spectrometer) was used as a particle measurement instrument that can measure particle concentrations from 5 nm to 1000 nm. Nano-particles of sizes less than 30 nm were reduced by oxidation or coagulated with solid particles in the tail-pipe and DOC. The DPF has a very high filtration efficiency over all operating conditions except during natural regeneration of DPF.

• Korean Journal of Materials Research
• /
• v.11 no.2
• /
• pp.132-136
• /
• 2001

Iron- silicide has been produced by mechanical alloying process and consolidated by hot pressing. As-consolidated iron silicides were consisted of $\beta$-FeSi$_2$ phase, and untransformed mixture of $\alpha$-$Fe_2Si_5$ and $\varepsilon$-FeSi phases. Isothermal annealing has been carried out to induce the transformation to a thermoelectric semiconducting $\beta$-$FeSi_2$ phase. The condition for $\beta$-FeSi$_2$ transformation was investigated by utilizing DTA, SEM, TEM and XRD analysis. The phase transformation was shown to be taken place by a vacuum isothermal annealing at $830^{\circ}C$ for 24 hours. The mechanical and thermoelectric properties of $\beta$-FeSi$_2$ materials before and after isothermal annealing were characterized in this study.

• Journal of the Korean Magnetics Society
• /
• v.16 no.4
• /
• pp.211-215
• /
• 2006

Measurement methods in order to measure the mechanical properties nondestructively have been studied. The mechanical properties of the structural and turbine rotor steels are related with their magnetic properties. If the magnetic properties of the cold rolled carbon steel sheet (CR) for a car are measured nondestructively, its mechanical properties are analogized by their magnetic properties. And then the mechanical properties are monitored on-line by measuring the magnetic properties. We prepared three CR materials, CBQ 3060, CBQ 3041, and CBQ 3036, were prepared in order to measure their mechanical and magnetic properties. The Vickers hardness,yield strength, and tensile strength were measured by ASTM E 8M, and the reversible magnetic permeability was measured by the surface type probe. The coercivity calculated by the peak interval of reversible magnetic permeability increased linearly with the increase of Vickers hardness, yield strength, and tensile strength. The amplitude of the peak interval of reversible magnetic permeability drastically decreased when the lift-off was increased.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.36 no.7
• /
• pp.737-744
• /
• 2012

A mobile emission laboratory (MEL) was designed to measure the amount of traffic pollutants, with high temporal and spatial resolution under real conditions. Equipment for the gas-phase measurements of CO, NOx, $CO_2$, and THC and for the measurement of the number, concentration, and size distribution of fine and ultra-fine particles by an FMPS and CPC was placed in a minivan. The exhausts of different types of vehicles can be sampled by an MEL. This paper describes the technical details of the MEL and presents data from the experiment in which a car chases passenger vehicles fuelled by diesel and gasoline. The particle number concentration in the exhaust of the diesel vehicle was higher than that of the gasoline vehicle. However, the diesel vehicle with a DPF emitted fewer particles than the vehicle equipped with a gasoline direct injection engine, with particle diameters over 50 nm.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.36 no.1
• /
• pp.83-88
• /
• 2012

Real slug and bubbly flows were measured using a three-ring impedance meter that can efficiently measure the void fraction of two-phase flows in a tube. First, the fitting curves between the signal from the impedance meters and the void fraction were found. The impedance meter had different fitting curves for slug and bubbly flows that had the same void fraction. An impedance meter should choose one of the two fitting curves according to the flow pattern, and the flow patterns can be recognized using the measured void fraction. The velocities and sizes of the bubbles were calculated using the void fraction curves measured by two impedance meters.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.17 no.5
• /
• pp.1313-1320
• /
• 1993

Flow patterns inside the riser section and the effects of the heater inlet-and exit-restrictions, liquid charging level and the heater inlet subcooling on the flow characteristics inside an open two-phase natural circulation loop were studied experimentally. Three basic circulation modes were observed ; periodic circulation (A)(flow oscillations with incubation(no boiling) period), continuous circulations(stable operation mode with no flow oscillations), and periodic circulation (B) (flow oscillations with continuous boiling). The circulation rate increases and then decreases with the increase of the heating rate and the maximum circulation rate appears with the continuous circulation mode. The decrease of the inlet-restriction or the increase of the exitrestriction destabilizes the system. When the liquid charging level or the inlet subcooling decreases, the continuous circulation mode starts at the lower heating rate and the system is stabilized.

• Proceedings of the Korean Society for Agricultural Machinery Conference
• /
• 2003.07a
• /
• pp.440-446
• /
• 2003

농산물의 품질 향상과 생산성 증대를 위해 농약의 적절한 사용이 필요하다. 그러나 농약을 적절히 사용해도 수확 농산물의 표면이나 내부에는 농약이 잔류할 가능성이 항상 있다. 농약의 과다한 잔류는 국민 보건상 커다란 문제가 될 수 있으므로 농약의 잔류량을 신속히 측정할 수 있는 분석법이 절실히 요구되고 있다(박, 2003). 살충제 Imidacloprid는 유기인계 살충제로 해충에 전신마비, 이완, 활동성 저하 등을 일으켜 박멸한다. 국내에서는 귤굴나방, 조팝나무 진딧물, 벼멸구, 굼벵이 류 등의 방제를 위해 감귤, 사과, 고추, 배, 장미, 복숭아 및 벼농사에 광범위하게 사용되고 있다(Bayer CropScience-Korea, 2002). (중략)

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2004.05a
• /
• pp.124-124
• /
• 2004

최근 MEMS공학의 발전으로 미소 가공물과 그 미소 가공물을 가공하는 공작기계의 발전이 두드러지고 있다. 마이크로 성형기는 이러한 미소 가공물을 만드는 공작기계들 중의 하나이다. 마이크로 성형기(micro former)는 마이크로 홀(micro holl)을 만드는 성형기로써 크랭크 축의 회전에 의한 펀치의 직선 운동으로 마이크로 홀을 뚫는 성형기이다. 마이크로 홀을 성형할 때에는 상하, 좌우의 미세한 변위가 생길 수 있다.(중략)

• 한국기계연구소 소보
• /
• s.20
• /
• pp.21-26
• /
• 1990

In order to satisfy the industrial requirements to measure the rotational error motion of main spindles and to find out the source of the error motion, some measuring systems were made. Their measuring principle are based on the 3-point roundness measurement. In these measuring systems, the measurements are processed by digital calculation technique and the form error and the rotational error motion of main spindles are spearated. In the present paper, the principle of 3-point metnod is introduced and some application examples are shown.

• Journal of the KSME
• /
• v.29 no.5
• /
• pp.525-537
• /
• 1989

본교에서는 정압 공기베어링의 특성 및 다공질 정압 공기베어링의 현황, 문제점등에 대한 개괄적 인 소개를 하였다. 이상에서와 살펴본 바와 같이 정압 공기베어링은 고속, 고정도를 요하는 각종 산업용기기의 부품으로써 연구개발, 응용되어 왔으며 결과적으로 기술한계극복에 많은 기여를 하 였다. 앞으로의 첨단기술을 위주로 한 각종 가공, 측정분야에 있어서도 공기베어링은 많은 역할을 할 것이며 특히 다공질베어링을 중심으로 한 고강성 정압 공기베어링에 대한 기대는 매우 크다고 할 수 있다.