• Korean Journal of Metals and Materials
• /
• v.48 no.5
• /
• pp.387-393
• /
• 2010

High-strength aluminum alloy sheets with high magnesium contents were fabricated by a strip caster equipped with an asymmetric nozzle, which has been proven to be effective for reducing surface defects and internal segregation. 4 mm thick as-cast sheets consisting of fine dendrites and minor $Al_{8}Mg_{5}$ segregation were hot-rolled successfully to 1 mm sheets and subsequently annealed at various temperatures. The sheet revealed the tensile strength and elongation of 306 MPa and 34%, respectively, when it was rolled at 250${^{\circ}C}$ and subsequently annealed at 475${^{\circ}C}$, which exhibits the feasibility of the practical application for autobodies. The observed mechanical properties were explained on the basis of the microstructural characteristics of the alloy sheets.

• Korean Journal of Metals and Materials
• /
• v.49 no.3
• /
• pp.243-249
• /
• 2011

This study describes the feasibility of producing high-strength Al alloy sheet with a high solute content using a combined technique of twin-roll strip casting and asymmetric rolling. The Al sheet produced in this study exhibited excellent formability ($\overline{r}$ =1.0, $\Delta$r=0.16) and mechanical properties ($\sigma_{TS}$~305 MPa, $\epsilon$~33%), that, cannot be feasibly obtained via the conventional technique based on ingot casting and rolling. The structural origin of the observed properties, especially enhanced formability, was clarified by examining the evolution of textures associated with strip casting and subsequent thermo-mechanical treatments. Our evaluation of the mechanical properties and formability leads us to conclude that the combination of strip casting and asymmetric rolling is a feasible process for enhancing the formability of Al alloy sheets to the level beyond what the conventional techniques can reach.

• Journal of Ocean Engineering and Technology
• /
• v.13 no.3 s.33
• /
• pp.21-28
• /
• 1999

In this paper, a finite element method for the determination of initial blank shape in sheet metal forming process will be introduced. The initial blank shape is determined by the only one step from the final to the initial blank. The used finite element inverse method adopted Henky's deformation theory, Hill's anisotropic yield criterion and simplified boundary conditions. Based on this theory. a three-dimensional membrane finite element code was developed. The developed code will be applied to several sheet metal forming examples for the demonstration of its validity.

• Transactions of Materials Processing
• /
• v.8 no.1
• /
• pp.29-37
• /
• 1999

An analysis system for sheet metal forming(SAT_STAMP) has been developed to improve the design and tryout process by predicting the deformation behavior more precisely. This analysis system consists of forming analysis, springback analysis and post processor modules. The more accurate prediction of stress history can be achieved due to the improved contact algorithm. Continuous simulation of sequential processes can be carried out conveniently without interruption by the improved data management of the developed system. The error of data transfer between forming analysis and springback analysis is minimized using the proper shell element. Several benchmark test results and practical results are presented to show the effectiveness and reliability of this program.

• Transactions of Materials Processing
• /
• v.8 no.4
• /
• pp.347-355
• /
• 1999

The paper is concerned with an improved scheme for application of the blank holding force in order to take account of the thickness distribution in the sheet material of the flange region. The scheme incorporates with a modified membrane finite element method for planar anisotropic materials. The new scheme proposed two coefficients α and βto calculate the compressive stress in the sheet metal due to the blank holding force, which should be determined properly for accurate analysis. The effect of αand βon the blank holding force distribution and the deformed shape is investigated with simulation of rectangular cup deep drawing processes by changing parameter values.

• Journal of the Korean Society for Precision Engineering
• /
• v.9 no.2
• /
• pp.101-107
• /
• 1992

디입그로잉용 냉간 압연 강판의 인장시험편에 디지탈 이미지 프로세싱 기술을 적용하여 표면에서의 변형 및 변형도 분포 구하는 방법을 제안한다. 이 방법은 시편표면상의 절점 위치를 이미지 프로세싱에 의해 결정하는 부분과 이들 위치점들을 이용하여 변형도를 계산하는 두 부분으로 구성되어,있다. 본 연 구에서는 시편상의 각 절점 위치를 구하기 위해 검은 원형의 반점들로 배열된 사각 형상의 격자를 사용하 였고, 이미지 프로세싱에 의해 구해진 절점 좌표를 이용하여 소재 표면에서의 변형 패턴, 주 변형도 분포, 유효 변형도 분포, 임계 변형도 등을 구하였다. 인장시험하는 동안 시편 표면상의 국부 네킹이 발생될때 까지 주변형도에 의한 변형 이력은 거의 적선적으로 변형되고 있기 때문에, 유효 변형도 값은 매 변형 단계마다 변형도 증분의 누적에 관계없이 거의 일정한 값을 보여주고 있었으며, 최대 유효 변형도는 시편의 중앙부에서 나타나고 있음을 알 수 있었다.

• Proceedings of the Korean Society For Composite Materials Conference
• /
• 2000.04a
• /
• pp.135-138
• /
• 2000

본 논문에서는 열팽창계수(CTE)가 거의 없는 카본게폭시, PZT 세라믹 박판, 그리고 열팽창계수가 큰 글래스/에폭시 층으로 이루어진 곡면형 복합재료 작동기(LIPCA)의 설계, 제작 및 성능실험에 대한 연구성과를 제시하고 있다. LIPCA의 른 요점은 기존 THUNDER의 성능을 유지하면서 이를 경량화 하기 위하여 THUNDER의 금속 층을 상대적으로 가벼운 섬유 강화 복합재료로 대체하는 것이다. 이러한 경량화 작업으로 LIPCA는 기존 THUNDER 보다 약 30~40% 정도의 무게를 감소시킬 수 있으며, 복합재료의 특성에 따라 설계의 유연성을 가질 수 있는 장점이 있다. 또한, 에폭시 수지를 사용함으로써 접착제 없이 평판 몰드에서 오토클레이브에서 177$^{\circ}C$로 경화되어, 탈형된 후 충분한 곡률을 형성하였다. 작동 성능 실험에서, LIPCA는 기존 THUNDER보다 작동변위가 향상됨을 보였다.

• Journal of the korean Society of Automotive Engineers
• /
• v.7 no.3
• /
• pp.42-55
• /
• 1985

The study is concerned with the investigation of curved line folding of developable surface from flat sheets of metal. General geometric relations among folding line, folded surface, folded angle are derived. From the derived geometric relations, the required plastic work and punch force are derived for the first approximation. Five methods of forming are suggested and the experiment is carried out using two chosen methods for the prismatic developable surfaces of which cross-sections have 103.deg.arc, 180.deg.arc, sinusoidal shape. In the die design for the tolding of prismatic developable surfaces, a stack of sheets were used to form shapes of the dies by which acceptable folded surfaces were obtained. The computed plastic work and punch force turned out to be in reasonable agreement with the experimental result.

• Journal of the Korean Society for Precision Engineering
• /
• v.21 no.2
• /
• pp.116-121
• /
• 2004

In rigid-plastic finite element method, there is a heavy computation time and convergence problem. In this study, static-explicit rigid-plastic finite element method will be introduced. This method is the way that restrict the convergence interval. It is expected that various results from the numerical analysis will give very useful information for the design of tools in sheet metal forming process.

• Transactions of Materials Processing
• /
• v.20 no.1
• /
• pp.64-72
• /
• 2011

In this study, we have investigated bonding of metal and plastic parts with single planar interface. This is facilitated by surface processing of aluminum sheet, which consists of slitting and punching, followed by insert-molding of polybuthylelne terephthalate(PBT). An injection mold has been built to fabricate specimen. After processing of the specimen, tensile and bending shear adhesion tests have been fulfilled according to KS M3734 and KS M3723, respectively. We also have conducted simulation of tensile and bending shear adhesion tests. Based on the tests results, the proposed bonding method outperforms existing methods based on adhesion.